'EPDM 70.503-00 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'01/U60EP 'O'-rings & gaskets'. Black coloured, injection moulded EPDM 'O' rings & gaskets. Shore hardness 60A. The ‘O’ rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radius size of 1.0mm. For use with water up to 85°C.
'Mescola EPDM-PX 659/70.nr'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP5360'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in -radius size 1.1mm. For use with water up to 85°C.
'CS-EW70'. Black coloured, compression moulded EPDM rubber. Shore hardness 70. Tested in-radius size 0.96mm. For use with water up to 23°C.
'0477 NBR 70' components. Black coloured, injection moulded NBR rubber ‘O’ rings, washers and lip seals. Shore hardness 70. The ‘O’ rings have an in-radius of 1.31mm, the washers 1.05mm and the lip seals 0.45mm. For use with water up to 60°C.
'Lavelle BUR165'. Red coloured, transfer moulded, silicone rubber gasket. Shore hardness 40A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Hinton Solvent Cement HSC125 & HSC250'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 02062023'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyfab uPVC Pipe'. Dark grey coloured, extruded uPVC pipe. For use with water up to 60°C.
Range of wall mounted, concealed, electronically controlled combination tap asselmblies (various finishes). The flow is controlled by a solenoid valve that is activated via an infra-red sensor which can be single or dual feed and incorporates lever operated isolation valves with stainless steel strainers. The spout outlet incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. Maximum working pressure 10.0 bar. Cold water use only.
Range of Concealed WC dual flushing cistern with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. Maximum working pressure -10 Bar Maximum operating temperature - cold water use only Models T1910 & T1911 can now incorporate a T8702 flush valve. Maximum working pressure 10 Bar, cold water use only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of flow restrictors with natural/unpigmented plastic bodies and inserts (where applicable), and EPDM ‘O’-rings. The LFB-FDN15, BFDN15SH & LFB-FDN15SH models also incorporate a stainless-steel filter.
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of ceramic disc headwork cartridges with diverter function, incorporating plastic bodies, NBR ‘O’-rings and silicone seals. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of thermostatic cartridges with brass (some of which are chrome plated), stainless steel or plastic bodies, for insertion into specifically dimensioned bores. All models (except for models TWK-5T, TWK-13 and TPWK-26A) incorporate a stainless-steel strainer.
Non-metallic materials and components comply with BS6920 at 85°C
Range of single-hole, single outlet, (fixed), combination tap assemblies, (chrome plated brass bodies. Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: See Models
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (chromium plated), incorporating ceramic cartridge headworks, a single lever operating member and a plastic aerator. The products are supplied with either a lever type pop up waste or a click type waste. Maximum operating pressure 10.0 bar. Maximum working temperature 60°C.
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a click-type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of deck mounted, single-hole, fixed combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating members. The spout outlets incorporate plastic aerators. Models 26216 and 26216MINI are fitted with pre fitted copper tails and provide 3/8” BSP to ½” BSP adapters and isolation valves. Models 2621 and 2621MINI are provided with pre-installed steel braided PEX lined flexible hose assemblies with ⅜” captive nut end connections. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a quarter turn ceramic disc (model VL113) or a non-rising spindle headwork (models VR113) with lever, cross top or dome type operating members. The spout outlets incorporate a flow straightener. Maximum working pressure 6.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range single hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating either a ceramic cartridge headwork or ceramic disc headworks with various operating members (see model). The spout outlet of some models incorporates a plastic aerator (specific models only - see model). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies (brass bodies, various finishes - see model), incorporating either a ceramic cartridge headwork with a single lever operating member or ceramic disc headwork with cross top operating members (see model). The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a waterfall type which also incorporates a stainless-steel mesh on the F7 and F9 prefix models. Maximum operating pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of floor mounted single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with either a lever or joystick type operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes). Incorporating a ceramic cartridge headwork and a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with a single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single-hole,single outlet, (swivel) combination tap assemblies (brass bodies – various finishes). Incorporoating ceramic headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet, (swivel), combination tap assemblies (chorme or supersteel plated brass bodies). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assembly (stainless steel body) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (swivel) combination tap assemblies (brass body - varies finishes incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assembly with brass body (various finishes). Incorporating either a ceramic cartridge headwork or ¼ turn ceramic disc (see models) with either single lever, dome type or cross top operating members (see models). The spout outlet incorporates a plastic aerator (excluding model F6136). Maximum working pressure - 10 Bar. Maximum operating temperature - 65 °C.
Non-metallic materials and components comply with BS6920 at 65°C
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) pull out spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator and a push button spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 65.0°C
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet (swivel), pull down, combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet is a handspray mechanism that incorporates a plastic aerator and a button to divert between the aerator and the spray function. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel), pull down, combination tap assemblies (chrome plated brass) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet is a handspray mechanism that incorporates a plastic aerator and a button to divert between the aerator and the spray function. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (swivel) combination tap assembly (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. This product is supplied with a click type pop up waste. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Floor mounted, single hole, single outlet (swivel) combination tap assembly (brass body – various finishes), incorporating two ceramic cartridge headworks with single lever operating members, with the upper headwork functioning as a manual diverter, diverting flow between the spout outlet and shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure: 10 Bar. Maximum operating temperature 65°C.
Range of two-hole, single outlet fixed combination tap assemblies, incorporating quarter turn ceramic disc headworks with single lever headworks. The spout outlet incorporates a plastic aerator. The product is supplied with metal back nuts. Maximum working pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of two hole, single outlet fixed combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic flow straightner. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of two-hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating ceramic disk headworks with single lever operating members and manually operated diverters to shower outlets. The spout outlets incorporate plastic aerators (T7111, T739001 & T740001) or plastic flow straightners (T7501M & T749001),except model T8701 that has an open spout outlet. The products are supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C (on model T740001).
Range of deck mounted, two-hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a half-turn ceramic disc headwork, both controlling the flow and manually diverting the flow to a shower outlet connection. Temperature is controlled independently via a thermostatic cartridge. The spout outlet incorporates a plastic aerator. Both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Page 67 of 177
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
