'Klinger K49'. Black coloured, braided compression packing. For use with water up to 85°C. For use only as a gland packing material having been tested at a reduced surface area to volume ratio.
'Graphalloy Bushing Grade GM 690'. Grey coloured, resin impregnated, carbon/graphite material. For use with water up to 23°C.
'OKS 1035/1'. Colourless (transparent) Silicone Oil lubricant. Apply as per manufacturer's Product Information dated '13.02.2024'. Between March 2024 and July 2024, the material is for use with water up to 60°C. Between August 2024 and March 2029, the material is for use with water up to 85°C.
‘TECHNYL ® SAFE A 219WFC V50 BK’. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
'Icorene 1440 NAT & Icorene 1440 BLK 9001'. Natural (appears off-white) & black, rotationally moulded polyethylene materials. For use with water up to 23°C.
'NORYL FE1410PW - 801' (appears yellow-cream coloured) & 'NORYL FE1410PW - 960' (light-grey coloured). Injection moulded PPE & PS materials. For use with water up to 85°C.
XYRON™ WG725 AWY2139 (off-white). XYRON™ WG725 AWY6633 (beige). XYRON™ WG725 AWY3328 (black) XYRON™ WG735 AWY3327 (black) XYRON™ WG735 AWY2138 (grey). XYRON™ WG735 AWY2272 (grey) XYRON™ WG735 AWY6632 (beige). Injection moulded, Modified Polyphenylene Ether materials. For use with water up to 85°C.
'TCM CPRO'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 02.03.2019. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ERIKS 559706'. Black coloured, EPDM 'O' ring with a vulcanised joint, manufactured by extrusion. Shore hardness 70 ShA. Tested in-radius size 8.0mm. For use with water up to 23°C.
'EP70-S3150/B1-73898 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'EPDM 5518 Seal 3G'. Black coloured, compression moulded, EPDM rubber seal. Shore hardness 58. Tested in-radius size 1.92mm. For use with water up to 23°C.
'EW gasket material'. Black coloured, injection moulded, EPDM gasket material. Shore hardness 65A. Tested in-radius size 3.9mm. For use with water up to 65°C.
'E6029 (shore hardness 70) & E6392 (shore hardness 80)'. Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'‘Welding polymer for Kryoclim®️, Girair®️ and HTA (formerly known as GIRPI HTA Fusion THF Free'. Site applied, orange coloured solvent cement, intended to join PVC-C pipe and fittings. Apply as per pages 4.2 & 4.3 of 'Durapipe HTA®' technical data sheet '04900200 February 2013'. Cure for 24 hours at 7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (brass bodies - in various finishes), incorporating a ceramic cartridge headwork with a single lever operating member, a manual diverter to shower outlet and a waterfall type spout. Shower hose and handset is not supplied with this product. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies, (chromium plated brass body). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet adapters incorporate stainless steel filters and single check valve cartridges verified by test (suitable for backflow protection against Fluid Category 2 ). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Deck mounted single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve actuated via an infra-red sensor. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlets incorporate approved check valve cartridges, however, the complete assembly has not been fully tested to demonstrate that it provides backflow protection and stainless-steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) electronically controlled, tap assemblies (chromium plated brass). The flow is controlled via solenoid valves, actuated by infra-red sensors. Temperature is manually blended using a single lever operating member. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of deck mounted, electronically operated tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve and actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlet hose connection incorporates a stainless-steel strainer. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass), incorporating a solenoid valve controlling the flow which is actuated via infrared sensor. The spouts incorporate plastic aerators. Maximum working pressure 8.0 Bar. Maximum operating temperature 65.0°C
Range of single hole, single outlet electronically controlled tap assemblies (chromium plated brass). Flow is controlled using a solenoid valve and actuated via the infrared sensor. The spouts incorporate a plastic aerator. Maximum operating pressure 8.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) over the rim swivel nozzle bidet combination tap assembly (brass body - various finishes) with a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic flow straightener. The product is supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of ceramic cartridge headworks and ceramic disc diverter headworks with plastic bodies, EPDM and/or silicone seals. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc headworks with brass bodies and EPDM O rings. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The products incorporate a pull-out spout with a plastic aerator. Both models incorporate an approved check valve cartridge within the quick connector to the pull-out hose, and the inlet to the pull-out spout of the 63036-01X model incorporates an approved check valve cartridge with a plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assembly (various finishes), incorporating quarter turn (/L or /F models) or half turn (/H models) ceramic disc headworks. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of deck mounted single hole, single outlet (fixed) combination tap assemblies (chromium plated brass). Incorporating ceramic cartridge headwork, and single lever operating member. The spout outlet incorporates a plastic flow straightener and supplied with a flow regulator. Model 23.112 is supplied with a lever type pop-up waste (not tested). Maximum working pressure 10 bar. Maximum working temperature 60°C
Range of single hole, single outlet (fixed), combination tap assemblies incorporating, (chrome plated brass bodies),with single lever operating members. The spout outlet incorporates a plastic flow straightener. Some products are supplied with a lever operated pop-up waste (not verified by test). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a waterfall type outlet. The inlets incorporate plastic flow regulators. Maximum working pressure 3.5 Bar. Maximum operating temperature 60.0°C
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a plastic aerator or a plastic flow straightener. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model). The 63691-00X and 63693-00X models incorporate a ceramic cartridge headwork with a single lever operating member. The 63692-00X model incorporates ¼ turn ceramic cartridge headworks with single lever operating members. The 63693-00X model incorporates a pull-down spout. All spouts incorporate a plastic aerator. The 63691-00X and 63692-00X models are also supplied with an alternative aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Description Greenstart 4000 Combi DHW Pre-heat kit, Preheat accessory assembly for connection to the domestic hot water circuit of a combination boiler max working pressure 10 bar max operating temperature 82℃
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum operating pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. Some models incorporate open outlet or waterfall spouts. The products are supplied with metal back nuts. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Wall mounted, concealed, two hole, single outlet (fixed) combination tap assembly (chromium plated or black finish brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Floor mounted two hole, single outlet (swivel) combination tap assembly (chromium plated brass). Incorporating a quarter turn ceramic disc headwork with either a single lever (25943819 model) or cross top (25943809 model) operating members and a manually operated diverter to shower outlet. The outlet connection to the shower hose and the inlet of the shower handset each incorporate a single check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. The products are supplied with shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The spout outlet of the 62638-5101 model incorporates a plastic aerator. The product is supplied with a shower hose and handset and metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Two hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a manually operated diverter to shower outlet. The product incorporates a plastic flow limiter on each inlet and has a waterfall spout. The product is supplied with a shower hose and handset and plastic backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (fixed), deck mounted combination tap assemblies (chromium plated brass), incorporating ¼ turn ceramic disc headworks with single lever operating members (T7401 has cross top operating member) and a manual diverter to the shower outlet. The spout outlet incorporates an aerator or are open outlet and the product is supplied with metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model), incorporating quarter turn ceramic disc headworks with either cross top, dome type or single lever operating members (see model). The spout outlet, excluding the F6134 & F6144 models, incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of two-hole, single outlet (swivel) combination tap assembly with brass bodies (chrome plated), incorporating non-rising spindle headworks with dome type operating member and a quarter turn ceramic disc headwork with single lever operating member. The spout outlet incorporates a plastic aerator or plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 6.0 Bar Maximum operating temperature 65.0°C
Range of two-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlet incorporates a plastic aerator or flow straightener and the products are supplied with metal backnuts. Maximum working pressure 10.0 bar Maximum operating temperature 65°C.
Range of two-hole, single outlet (fixed) combination tap assemblies, various finishes incorporating quarter turn ceramic disc headworks with various operating members and lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The products are supplied with metal backnuts. Maximum working pressure 10.0 bar. temperature 60°C.
Three hole, single outlet (swivel) combination tap assembly (brass body - various finishes), incorporating quarter turn ceramic disc headworks with dome type operating members. The spout outlets incorporate a plastic aerator. The product is supplied with stainless steel braided PEX lined flexible hose assemblies, for use between the valves and spout. Also supplied with a lever type pop up waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Page 56 of 83
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
