'Silicone Rubber Washer SIL40 (SIL4001)'. Black coloured, vulcanised silicone rubber washer. Shore hardness 40. Tested in-radius size 0.56mm. For use with water up to 85°C.
'Type 1 O-ring, T056D 124H16 Model Code P16'. Cream coloured (opaque), compression moulded silicone rubber 'O' ring. Shore hardness 70. Tested in-radius size 1.2mm. For use with water up to 85°C.
'Tangit Rapid'. Straw coloured adhesive intended to join pipe and fittings. Apply as per manufacturer’s instructions ‘TFU_TM_GB_0915’. Cure for 24 hours@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Fosroc Nitoseal SC600'. Site applied, grey coloured silicone sealant waterstop. Apply as per manufacturer's TDS issue '1.0', dated October 2024. Cure for 21 days at 7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval. These materials are for use in concrete reservoirs and similar structures, constructed in accordance with the design criteria of BS EN 1992-3:2006 (Design of concrete structures – Liquid retraining and containing structures) with respect to normal frequency of joints. The material has been tested at a reduced surface area to volume ratio of 1000mm² per litre.
'Loctite 5800'. Red coloured anaerobic adhesive. Apply as per manufacturer's technical data sheet dated April 2012. For use with water up to 85°C. These products are to be applied and cured in strict accordance with the manufacturer's instructions
Range of single-hole, multiple outlet, swivel, combination tap assemblies (brass bodies - various finishes) a quarter turn ceramic disc controlling the flow to the swivel arm with a dome type operating member and a ceramic cartridge with a single lever controlling the flow to the pull-out spray outlet incorporating a plastic aerator. The spray outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 bar. Maximum operating temperature for boiling water pathway 98°C, for mixed water pathway 65C and purified water pathway 85°C
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Non-verifiable double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-verifiable double check valve assemblies incorporating two spring loaded resilient trim in-line check valve cartridges, DZR brass bodies (brushed chrome) and a drain port located in between the cartridges. The assemblies incorporate spherical valve. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C.
Range of aerators with plastic bodies and EPDM ‘O’-rings. Maximum operating temperature 65°C Open outlet use only
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of ceramic disc headworks with brass bodies. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headworks with a plastic body, incorporating silicone seals. The product is intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure - 10 Bar Maximum operating temperature - 85 °C
Range of thermostatic cartridges with either brass or plastic bodies, for insertion into specifically dimensioned bores. Maximum operating temperature 85°C.
Range of single hole, single outlet, (swivel), combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The outlet is a pull-down spray type and incorporates a plastic aerator. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (swivel) pullout spray combination tap assembly (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 483 of 566
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
