Range of gate valves with blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. DN50 to DN500 sizes are operated by handwheel. DN600 to DN800 sizes are operated by a gear box. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with ductile iron bodies (blue epoxy powder coated) incorporating EPDM encapsulated Wedge and bonnet with EPDM `O` rings and gaskets. Valves incorporate handwheel type operating member. Maximum working pressure 16.0 Bar. Maximum operating temperature 60.0°C
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass or DZR brass bodies, non-rising spindles and either hand wheel or lockshield operating members. The 4366 and 4363 compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves, brass body and disc with a handwheel operating member. Maximum working pressure 20.0bar Maximum operating temperature 100°C
Angled servicing valves with chrome plated brass bodies incorporating dome type operating member. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
Range of water conditioners with stainless steel bodies. AFL012 MFB has a matt black finish and AFL012MFC has a chrome plate finish. Models with compression connections are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C.
Range of UV disinfection units with titanium bodies.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
'JDFF-OPC-01'. Factory applied, grey coloured Ordinary Portland Cement. Mix cement, sand & water in a 1:2:0.50 weight ratio and apply as per manufacturers Work Instruction 'WI-Pc-01-5', 'Issue #: 5 Revision #: 1', dated '10.01.2025'. Cure for 48 hours@23°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Endolac® 245.10'. Factory applied, black coloured bituminous paint. Apply as per manufacturer's TDS 'Version edit: 17/04/2024'. Cure for 7 days at 20°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement CEM1-SR3 - Dalmia SRPC'. Factory applied, grey coloured sulphate resisting Portland cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chromapoxy H.B.F.N.Paint Blue'. Factory applied, blue coloured, two-part epoxy coating. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet 'NCE/200', issue date '15.01.2014'. Cure for 7 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER CM-4'. Factory applied, grey coloured Portland Cement. Mix sand, cement and water in a 40:20:40 weight ratio and apply as per manufacturer's instruction sheet 'Revision: A1', dated '2023-11-15'. Cure for 4 hours at 23°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Loxeal Olio 1000'. Clear, silicone oil based lubricant. For use with water up to 70°C.
‘RIALENE P 100 SGFxx KTW grau K 7-128, RIALENE P 100 SGFxx KTW weiß K 9-112, RIALENE P 100 SGFxx KTW schwarz’, injection moulded polypropylene materials available in grey, white and black. ‘RIALENE P 100 SGFxx KTW natur(al)’, natural (appears off-white), injection moulded, polypropylene material was added to the approval in February 2026. The ‘xx’ in the material name can be replaced with any number between ‘10’ and ‘50’. For use with water up to 85°C.
'ASHUTOSH EPDM 50' & 'ASHUTOSH EPDM 80'. Black coloured, compression moulded EPDM materials with a shore hardness of 50 & 80. Tested in-radius size 1.2mm. For use with water up to 23°C.
'NER EPDM - 80'. Black coloured, compression moulded EPDM material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 50°C.
Page 427 of 522
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
