Range of inline, angled or tee type spherical valves with nickel plated brass bodies and chromium plated brass balls. The valves are either screwdriver or lever operated(see model). The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 25.0 bar (HC-A61055-22 model) or 16.0 bar (all other models). Maximum operating temperature 85°C.
Range of press fit spherical valves with brass and chrome plated brass bodies. For use with copper pipe to BS EN 1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of gate valves with a non-rising spindle with a handwheel operating member or lockshield connection. All models have brass and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of press fit gate valves with brass bodies. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
OS & Y Range of gate valves with blue, black or red epoxy coated ductile iron bodies, incorporating ductile iron wedges encapsulated in EPDM and hand wheel operating members. Maximum working pressure - 16 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of screw down stop valves with brass bodies, EPDM gaskets and PTFE washers. For use with copper pipe to EN 1057. Maximum working pressure 16.0 Bar. Maximum operating temperature 99°C.
Range of press fit screw down stop valves with brass bodies and EPDM seals. For use with copper pipe to EN1057. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of inlet control groups with DZR brass bodies consisting of an in-line, adjustable pressure reducing valve (adjustable in the range of 1.0 bar to 6.0 bar, pre-set at 3.0 bar), a pressure relief valve (6.0 bar) and an approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 16 Bar Maximum operating temperature 85°C
Range of bedpan washers with the flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of electrolytic water conditioners, with a brass body and zinc alloy anodes. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline magnetic or electrolytic scale inhibitors with copper or bodies, for use with copper pipe (manufactured to BS EN 1057). Maximum working pressure 8.0 bar. Electrolytic models have a maximum operating temperature of 40°C. Magnetic models are cold water use only.
'BFSC MAS S&MDN 25'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a mass ratio of 1:2.35:0.45 and apply as per manufacturer's TDS 'SGMAS20111012-01', dated '2011.10.12'. Cure for 19 hours@70°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-02 Portland Cement Mortar'. Factory applied, grey coloured Portland cement mortar. Mix cement:sand:water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue reference 'Ascent02-2511', dated '2025.11.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BAJ0002'. Factory applied, blue coloured epoxy coating. Pre-heat substrate for 30 minutes@200°C and apply in accordance with manufacturer's Product Instructions 'Version-01 202426 September'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XX-CM1'. Factory applied, grey coloured cement mortar. Mix cement, sand, and water in a volume ratio of 1:2.0:0.4 and apply as per manufacturer's safety data sheet 'A1: 26-01-2020'. Cure for 5 hours@30°C and then steam cure for 6 hours@30°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'EPLAMID HT00 GFR 40 FW BK'. Black coloured, injection moulded, glass fibre reinforced PA 6T/6I material. For use with water up to 85°C.
'PAG11-YT60SF'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
'Prime Plastic Industries HDPE Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 60°C.
'Qingfa PE100 Black Pipe Fittings'. Black coloured, injection moulded HDPE fittings. For use with water up to 65°C.
'AQUACO HDPE Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
Page 415 of 443
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
