Range of UV disinfection units with stainless steel bodies and quartz tube. Maximum working pressure 10.0 bar. Cold water use only.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`Scotchkote 206N`. Factory applied, green coloured, epoxy powder coating. Apply and cure as per manufacturer’s 'standard cure guide' which appears in document '80-6111-8352-8 Rev. B'. For use with water up to 23°C.
'SADIP-Mix'. Factory applied, grey coloured cement mortar. Mix sand, cement & water in a mix ratio of 2:1:0.5 and apply as per manufacturer's 'quality work instruction' document 'QW 41A', issue 4 dated 20/11/97. Cure for 24 hours@25°C. The cement mortar must then be submerged in water for 72 hours before use. For use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'JDP21GEY‐5005, JDP21GEY‐5015 & JDP21GEY‐5017'. Factory applied, blue coloured, epoxy powder coatings. Apply as per manufacturer's Technical Data Sheet 'version 1.0', dated 15/02/2022. Cure for 20 minutes@180°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Belzona 1511 (Super HT – Metal)'. Site applied, two-component, silver/grey coloured (once mixed) epoxy coating. Mix parts A and B in a 5:1 mass ratio and apply as per manufacturer's instructions for use 'FN10178', publication number '07-06-21'. Cure for 18 hours@20°C then post-cure for 1 hour@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Regin REGQ102-115'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Crystic Vinyl Ester VE671PA'. Brown coloured (translucent), contact moulded GRP laminating material. For use with water up to 23°C.
‘SEA2001’ (manufactured in Italy, Poland & Turkey). Dual layer, extruded, composite hoses. Hoses with a black coloured inner layer and either a red or blue coloured outer layer are suitable for use with water up to 60°C. Hoses with a straw coloured, translucent inner and outer layer are suitable for use with water up to 60°C. Hoses with a black coloured inner layer and either a white or grey coloured outer layer are suitable for use with water up to 23°C. From January 2023 hoses with a black coloured inner layer and either a white or grey coloured outer layer are suitable for use with water up to 60°C.
'Molykote® 111 & Molykote® 7508'. Translucent white silicone greases. For use with water up to 85°C.
'Ferrimax 10T'. Grey coloured, sintered strontium ferrite magnet. For use with water up to 50°C.
'Tecomid NB30 GR50 BK012 QW'. Black coloured, injection moulded PA6 material. For use with water up to 85°C.
‘Radilon A RV300RKC 106 NT, A RV300RKC2 106 NT, A RV500RKC2 106 NT & A RV500RKC 106NT’ ‘Radilon A RV300RKC 306 BK, A RV500RKC 306 BK, A RV300RKC2 306 BK & A RV500RKC2 306 BK’. ‘NT’ indicates that the grade is natural (which appears beige in colour). BK indicates that the grade is black coloured. Injection moulded PA66 materials. For use with water up to 85°C.
'POLYPOL-1021'. Orange/brown coloured, isophthalic based, unsaturated polyester resin manufactured by contact moulding. For use with water up to 50°C.
'Shield PE100 Segmented Fittings'. Black coloured fittings manufactured by extrusion and butt-fusion. For use with water up to 85°C.
'Shield PE 100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 85°C.
'Icorene 3855 BLK 9001'. Black coloured, LDPE manufactured by rotomoulding. For use with water up to 23°C.
‘Tecotek OP20 GR10 NL 01 0A QF, Tecotek OP20 GR20 NL 01 0A QF & Tecotek OP20 GR30 NL 01 0A QF’. ‘Tecotek OP20 NL 01 0A QF’ was added to the approval in November 2023. Yellow/brown coloured, injection moulded, glass filled PPO/HIPS materials. For use with water up to 85°C.
Range of white coloured (opaque), PP filter media, which comprise of melt blown fibres laid onto an extruded core. ‘SupaGard’ range (complete range except B-Blue) with a micron rating of between 0.5μm & 200 μm. ‘SupaSpun’ (complete range) with a micron rating of between 0.3μm & 180μm. ‘Contour’ (complete range of lengths). For use with water up to 23°C.
‘Verplen C30 01 NE ACLKUV (black coloured), C30 04 NE ACLUV (black coloured), C30 08 NE ACLKUV (black coloured) & C30 08 NT ACLKUV (natural – appears beige coloured)’. Injection moulded, glass filled polypropylene materials. For use with water up to 60°C.
'F801'. White coloured, extruded PTFE material. For use with water up to 85°C.
'F391'. Blue/grey coloured, extruded PTFE material. For use with water up to 85°C.
'F1500'. White coloured, extruded PTFE material. For use with water up to 85°C.
'INOLUB™ T201F, T202F, T203F, T204F & T205F'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
`Soltane F/B 197`. White coloured, extruded thermoplastic polyurethane material. For use with water up to 60°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EP12/2/5 BLK 'O'-rings & seals'. Black coloured, injection moulded EPDM 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.0mm. The seals have a tested in-radius size of 0.75mm. For use with water up to 85°C.
‘4280’ black coloured injection moulded EPDM rubber components. Shore hardness 80. '4280 Membrane' has a tested in-radius size of 1.75mm. ‘4280 ’O’ rings’ have a tested in-radius size of 1.31mm. ‘4280 washers’ have a tested in-radius size of 1.05mm. All components are for use with water up to 85°C.
'XXE03'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.05mm. For use with water up to 85°C.
'RE EP/50, 'RE EP/60, 'RE EP/70 & RE EP/80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 60°C.
'SIL50 RED 'O' rings & seals'. Red coloured, injection moulded silicone 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.3mm. The seals have a tested in-radius size of 4.2mm. For use with water up to 85°C.
'Gebatout2'. Green coloured, polymer sealing paste. Apply as per manufacturer's instructions, 'version 11' dated 23/09/19. For use with water up to 85°C.
'Spears® FlameGuard® FS-5 One-Step'. Red/brown coloured, liquid solvent cement. Apply as per manufacturer's instructions 'FG-3-0321'. No cure required. For use with water up to 82°C.
'40810813 (3019 THF Free)'. Colourless (transparent) solvent cement. Apply as per manufacturer's fact sheet 'TDS00481' dated 20th July 2018. Cure for between 24 hours and 21 days@7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PK-HM 8 natural (6145) & PK-VM 8 natural (6146)’. Natural (appear beige in colour), injection moulded polyketone materials. For use with water up to 85°C.
Range of stop valves with plastic bodies and an EPDM diaphragm. The valves are operated via a switch located on the valve. The RCL and RPL models can also be operated by a remote switch. The product incorporates a plastic strainer central to the body. All valves are for use with copper pipe (manufactured to BS EN 1057). The PL suffix valves are also for use with PEX pipe (manufactured to BS7291-3). Models added Jan 2025 are for use with PE80 & PE100 pipes manufactured to BS EN 12201:2 at the inlets and the outlets are suitable for PEX pipe manufactured in accordance with BS7291 and copper pipe manufactured in accordance with BS EN 1057. For above ground use only. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body in various finishes), incorporating a ceramic disc headwork with single lever operating member (model OMI-133 & IND-OMI133-XXX) OR ceramic cartridge headwork with a single lever operating members (all other models) and a lockable self-cancelling diverter to shower outlet. All models except OMI-133-C/P and IND-OMI133-XXX are supplied with an approved check valve cartridge at the inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with a shower hose and handset. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted mirrored units incorporating an electronically controlled combination tap assemblies. Flow is controlled via solenoid valve which is actuated by an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. The trigger on the pull-out controls optional spray. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only.
Range of concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only
Range of spring loaded, resilient trim, in-line check valve cartridges, with EPDM seals and O-rings within a brass valve body and plastic insert body. For insertion in pipes and fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (chrome plated brass). Incorporating quarter turn ceramic disc headworks, single lever or cross top operating members. The spout outlets incorporate plastic aerators. The product is supplied with a pop up waste, verified by test. Maximum working pressure 10.0 bar Maximum operating temperature 65.0°C
Range of ceramic cartridges for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Page 40 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
