‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SADIP-Mix'. Factory applied, grey coloured cement mortar. Mix sand, cement & water in a mix ratio of 2:1:0.5 and apply as per manufacturer's 'quality work instruction' document 'QW 41A', issue 4 dated 20/11/97. Cure for 24 hours@25°C. The cement mortar must then be submerged in water for 72 hours before use. For use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal'. Factory applied, red-brown coloured (once mixed and applied), two-part polyurethane coating. Mix, apply and cure (full cure of 7 days@30°C) as per manufacturer's instructions ref. 'DI/PU/2022/072', dated 25/04/2022. For use with water up to 35°C.
'Purtop Easy DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS '7483-7-2021-I-gb'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KLINGERSIL® C-4324'. Fibre/rubber gasket material, manufactured by calendaring, which is green coloured on one side and black coloured on the other. Shore hardness 65. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'Crystic LS96PA Clear Gel Coat' for use with 'Crystic 2-446 PA GRP resin'. Contact moulded GRP resin, manufactured by hand lamination, for use with off-white coloured, factory applied gel coat. Apply as per manufacturer's quick guide 'issue number 1', dated 04/06/2018. Cure for 24 hours@23°C and then 3 hours@80°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Crystic 274E`. Olive coloured, contact moulded, GRP unsaturated polyester material. For use with water up to 23°C.
'Polylite 444-M888'. Amber coloured, unsaturated polyester resin material manufactured by liquid casting. For use with water up to 23°C.
'Poseidon Cable' (3 x 1.5mm, 4 x 1.5mm, 3 x 1.0mm & 4 x 1mm). Blue coloured (external water contact layer), extruded, XLPE electrical cable. For use with water up to 65°C.
'Pexylene 45939 Black'. Black coloured polyethylene material manufactured by rotomoulding. For use with water up to 85°C.
'LL 8460.29'. Natural (appears white and opaque) LLDPE material manufactured by rotational moulding. For use with water up to 85°C.
‘FORTRON 9115L0 SD3039 BLACK (formerly known as FORTRON MT9115L0 SD3039 DW black) & FORTRON 9141L4 SD3039 BLACK (formerly known as FORTRON MT9141L4 SD3039 DW black’). Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'BC 245 MO Polypropylene Cover'. White coloured, injection moulded, circular polypropylene cover component. For use with water up to 85°C.
‘FILTER NOZZLES P, PTL, P5, P6, P7, T, TTL, TD, R, RTL, RD, B, V, VL, C, D4, D3 & D9. NUTS N & HR. EXPANDING BOLT TS. VALVE BODIES DPI & DPS. SLEEVES G, GM & GE. COLLECTORS CSI05, CSI06, CST06, CSD06, CSI08, CST08, CSG08, CSD08 & CSI08. FILTER ARMS SF/SFC, SD, SB & SC. FILTER NOZZLES RB2 & RB3. DISTRIBUTORS RBD2 & RBD3’. Blue, black, dark grey, light grey, green, red, yellow & light blue coloured, injection moulded polypropylene components. For use with water up to 23°C.
‘Verplen C30 01 NE ACLKUV (black coloured), C30 04 NE ACLUV (black coloured), C30 08 NE ACLKUV (black coloured) & C30 08 NT ACLKUV (natural – appears beige coloured)’. Injection moulded, glass filled polypropylene materials. For use with water up to 60°C.
'INOLUB™ T201F, T202F, T203F, T204F & T205F'. White coloured, compression moulded PTFE materials. For use with water up to 85°C.
‘GF PVCU fittings manufactured from HS1013, IR348 & HS1014’. From September 2023 onwards, the fittings may also be made using 'IR 349'. Grey coloured, injection moulded PVC-U fittings. For use with water up to 60°C.
'Dragon STD'. Site applied, off-white coloured, two-part epoxy resin and fibreglass cloth. Mix resin in a 77.8@22.2 volume ratio and apply to the fibreglass cloth. Once the cloth is fully impregnated, apply to the defect as per manufacturer's instructions 'IMG MPW 020' dated 01.07.2022. Cure for 24 hours@21°C or 4 hours@100°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'V7500BK'. Black coloured, Fluororubber material manufactured by mould pressing. Shore hardness 75. Tested in-radius size 1.04mm. For use with water up to 23°C.
‘4280’ black coloured injection moulded EPDM rubber components. Shore hardness 80. '4280 Membrane' has a tested in-radius size of 1.75mm. ‘4280 ’O’ rings’ have a tested in-radius size of 1.31mm. ‘4280 washers’ have a tested in-radius size of 1.05mm. All components are for use with water up to 85°C.
'E2514'. Black coloured, compression moulded EPDM rubber. Shore hardness 67. Tested in-radius size 1.03mm. For use with water up to 60°C,
'XR0240012'. Black coloured, compression moulded EPDM material. Shore hardness 40. Tested in-radius size 1.5mm. For use with water up to 85°C.
'EPDM 69064340'. Black coloured, injection moulded EPDM sheet material. Shore hardness 57. Tested in-radius size 0.9mm. For use with water up to 23°C.
'Seat Seal S1 & S2'. Black coloured (S2) or white coloured (S1), injection moulded silicone rubber components. Shore hardness 80. Tested in-radius size between 0.65mm & 1.54mm. For use with water up to 85°C.
'SIL50 RED 'O' rings & seals'. Red coloured, injection moulded silicone 'O' rings & seals. Shore hardness 50. The ‘O’ rings have a tested in-radius size of 1.3mm. The seals have a tested in-radius size of 4.2mm. For use with water up to 85°C.
'40810813 (3019 THF Free)'. Colourless (transparent) solvent cement. Apply as per manufacturer's fact sheet 'TDS00481' dated 20th July 2018. Cure for between 24 hours and 21 days@7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PK-HM 8 natural (6145) & PK-VM 8 natural (6146)’. Natural (appear beige in colour), injection moulded polyketone materials. For use with water up to 85°C.
'XFGJ-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X20220228F' dated '2022-2-28'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SPS-2022'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'S20220601' dated '2022-6-1'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
Range of deck mounted, four hole, single outlet (fixed) combination tap assemblies with brass bodies, incorporating quarter turn ceramic disc headworks with either single lever, cross top or dome type operating members and a manual diverter to the shower handset. The product is supplied with a shower hose and handset. The headworks, main body and shower outlet are connected with hoses. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Wall mounted infra-red single hole, single outlet electronically controlled combination tap assemblies with brass body (chrome plated), incorporating a solenoid valve controlling the flow. The spout outlets incorporate a plastic aerator.Stainless steel strainer on inlet Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of deck mounted sensor taps. The flow is controlled via a solenoid valve and activated by an infra-red sensor on the front of the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of wall mounted mirrored units incorporating an electronically controlled combination tap assemblies. Flow is controlled via solenoid valve which is actuated by an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
A range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. These products are supplied with an inline servicing valve integrated with a strainer and single check valve assemblies that has been verified by test for back flow prevention level 2. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled combination tap assembles with brass bodies (various finishes). Flow is controlled via a solenoid valve activated via an infra -red sensor. The temperature is controlled via a ceramic cartridge and a single lever operating member. The spout outlet incorporates a pull-out spray with a plastic aerator. The trigger on the pull-out controls optional spray. The inlet adaptor incorporates a single check valve cartridge (verified by test, suitable for backflow protection against fluid category 2). The outlet incorporates a stainless-steel strainer and an aerator. Maximum working pressure 5.0 bar Maximum operating temperature 60°C.
Bottom entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water only.
Range of concealed WC flushing cisterns incorporating a side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC flushing cisterns incorporating a BS 1212-4 side entry compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only
Range of spring loaded, resilient trim, in-line check valve cartridges, with EPDM seals and O-rings within a brass valve body and plastic insert body. For insertion in pipes and fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridges for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and NBR O-rings. For insertion into specifically dimensioned bores. Maximum working pressure 10 bar. Maximum operating temperature 85°C.
Range of thermostatic cartridges with plastic bodies and NBR ‘O’-rings. All models incorporate a stainless steel filter. For insertion into specifically dimensioned bores. Maximum working pressure 5.0 bar. Maximum operating temperature 80°C. Maximum operating temperature 60°C for Model 0426AFOC1-001.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a click type waste. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates either a combined EPDM washer and stainless steel strainer with a plastic flow straightener, or an EPDM washer with a plastic aerator. The product is supplied with a click type waste, verified by test. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with or without a pop-up waste or a retractable chain. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes). Incorporating a quarter turn ceramic disc headworks with either single lever, dome or cross-top operating members. The spout outlets incorporate plastic aerators or flow straighteners with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Page 35 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
