'TCM CPRO'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 02.03.2019. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TCM100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 07.03.2024. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MILGERLAN EBONITE 1065G'. Black coloured, calendered natural rubber material. Shore hardness 65. Tested in-radius size 3.1mm. For use with water up to 23°C.
'EP70-S3150/B1-73898 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. For use with water up to 85°C.
'EPDM 5518 Seal 3G'. Black coloured, compression moulded, EPDM rubber seal. Shore hardness 58. Tested in-radius size 1.92mm. For use with water up to 23°C.
'EPDM 5711'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radii size between 0.5mm & 3.5mm. For use with water up to 85°C.
'3E60B11P/3E60B18P & 3E70B03P/3E70B16P'. Black coloured, compression moulded EPDM materials. Shore hardness 60 & 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E6029 (shore hardness 70) & E6392 (shore hardness 80)'. Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Jihua 3517'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP05280PWRC'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EH700-144'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM-LJHY'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 75. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SIL7018 red & SIL7018 blue'. Red and blue coloured, compression moulded silicone rubber 'O' rings. Shore hardness 70A. Tested in-radius size 2.6mm. For use with water up to 85°C.
‘7400, 7500, 7600, 7700 & 7800 ‘O’ rings’. Red coloured, compression moulded silicone rubber `O` rings. Shore hardness between 40 & 80. Tested in-radii sizes between 0.5mm & 2.0mm. ‘7700 washers’. Red coloured, compression moulded, silicone rubber rectangular washers. Shore hardness 70. Tested in-radius size 1.33mm. ‘7700 PLC091130 Profile Packing Seal’. Red coloured, compression moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 2.26mm. All for use with water up to 85°C.
'SYC3 0825 S30CB04 Boot'. Black coloured, compression moulded silicone rubber boot component. Shore hardness 30. The component has an irregular shape with a tested in-radius size of between 0.6mm & 1.2mm. For use with water up to 85°C.
'ADDISIL IND. 60 E’. Natural (appears white), injection moulded silicone rubber material. Shore hardness 60. Tested in-radius size 1.25mm. For use with water up to 85°C.
'MXLOC 12638, 38 & 48'. Green coloured acrylic based adhesives. Apply as per manufacturer`s instructions. For use with water up to 23°C.
MXLOC acrylic based adhesives. Apply as per manufacturer`s instructions. Grades for use with water up to 23°C. MXLOC 22 (purple coloured), 11243, 70, & 90 (green coloured). MXLOC 42 & 43 (blue coloured). MXLOC 542 (brown coloured). MXLOC 12638, 38 & 48 (green coloured). MXLOC 71 & MXBON 11271 (red coloured). Grade for use with water up to 85°C. MXLOC 13577, 577 & MXBON 13577 (yellow coloured).
'GIRPI HTA Fusion'. Site applied, orange coloured solvent cement, intended to join plastic pipe and fittings. Apply as per manufacturer instructions '6311289/20'. Cure for 24 hours@7°C. For use with water up to 70°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 325 of 509
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
