'4MID 9B22130 W-A BNL100'. Off-white coloured (translucent), injection moulded PA6 material. For use with water up to 85°C.
'Genestar™ G1500D-L47WF BLACK'. Black coloured, injection moulded or extruded Polyamide 9T material. For use with water up to 85°C.
'Bearing p/n 238717'. Grey coloured, injection moulded PEEK component. For use with water up to 70°C.
`Veradel 3330GF`. Beige coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'MT PE-Xc/AL/PE-X Pipe' (formerly known as 'Hewing MT PE-Xc/AL/PE-X multi layer pipe'). Extruded, multi-layered pipes comprising of an off-white (translucent), PEX-Xc inner layer, aluminium middle layer and white coloured (opaque), PE-Xb outer layer. For use with water up to 85°C. Please note that the pipes will be marked with 'WRAS 2111538'. Pipes which do not have this marking are not covered by the scope of the approval.
'Instantor® Pex'. Translucent, white coloured, extruded, single-layered PE-Xb tubing. For use with water up to 85°C.
'CORREX®, Q-GUARD® & S-PATRON® PE-Xc Anode Frame (Clip)'. Cream coloured, injection moulded PE-Xc clip components. For use with water up to 85°C.
'CORREX®, Q-GUARD®, S-PATRON® & HYTONIC® PE-Xc Anode Gasket'. Cream coloured, injection moulded PE-Xc gaskets. For use with water up to 85°C.
'002DP48 Aiva Electrofusion Fittings'. Blue coloured, injection moulded HDPE electrofusion fittings. For use with water up to 23°C.
'Kott-Glide 2.0'. Black coloured, extruded HDPE pipe. For use with water up to 85°C.
'EGPI HDPE BL-W Pipe'. Black coloured, (with blue coloured external stripe), extruded HDPE pipe. For use with water up to 85°C.
'C40'. White coloured, extruded polyethylene pipe. For use with water up to 85°C.
'K9'. White coloured, extruded polyethylene pipe. For use with water up to 85°C.
'Turbine Cage 241208'. Blue coloured, injection moulded PPO component. For use with water up to 70°C.
'Isoryl A 20 90 GF20 W NA'. Beige coloured, injection moulded PPO material. For use with water up to 85°C.
WOTLON MPPO 1000-GF2 BK006. WOTLON MPPO 1000-GF2 GY003. WOTLON MPPO 1000-GF2 NC001. WOTLON MPPO 1000-GF3 BK006 WOTLON MPPO 1000-GF3 GY003 WOTLON MPPO 1000-GF3 NC001 Natural (NC grades - appears beige in colour), black coloured (BK grades) and grey coloured (GY grades), injection moulded MPPO materials. For use with water up to 85°C.
'VIALLI PPR Pipes'. Green coloured, extruded PPR pipe. For use with water up to 85°C.
'SHK Aqua PP-R pipe'. Extruded, multi-layered PP-R pipe comprising of a white coloured inner, black coloured middle layer and green coloured outer layer. For use with water up to 85°C.
'Polygon PPR Pipe'. Green coloured (with red stripe), single layered, extruded PPR pipe. For use with water up to 85°C.
'Polygon PPR Fitting'. Green coloured, injection moulded PPR fitting. For use with water up to 85°C.
'Isoglas H30FVL (c) NA'. Translucent, off-white coloured, injection moulded, polypropylene material. For use with water up to 85°C.
`Polyfill PPH TS15040D Natural`. Natural (appears grey in colour), injection moulded polypropylene material. For use with water up to 85°C.
'Polyfill PPH GF8020 PB Natural'. Natural (appears off-white in colour), translucent, injection moulded polypropylene material. For use with water up to 85°C.
`Polyfill PPH T8020 1035 Grey & Polyfill PPHC T8040 1017 Grey'. Grey coloured, injection moulded polypropylene materials. Between February 2022 and September 2022, 'Polyfill PPHC T8040 1017 Grey' was for use with water up to 23°C. Between October 2022 and February 2027, 'Polyfill PPHC T8040 1017 Grey' is for use with water up to 85°C. 'Polyfill PPH T8020 1035 Grey' is for use with water up to 85°C.
`Acoflon 100`. White coloured, compression moulded PTFE washers. For use with water up to 85°C.
'AKORROS® B208A'. Brown coloured, extruded hard rubber Shore hardness 78. Tested in-radius size 1.11mm. For use with water up to 60°C.
'LOPI80 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 2.26mm. For use with water up to 85°C.
`EPDM7008`. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 2.7mm. For use with water up to 85°C.
'LOPI80 'O'-rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 80. Tested in-radius size 2.26mm. For use with water up to 85°C.
'70EP120P'. Black coloured, compression moulded, EPDM 'O' rings. Shore hardness 70. Tested in-radius size 0.5mm. For use with water up to 85°C.
'EPDM60BKFG, EPDM65BKFG, EPDM70BKFG, EPDM75BKFG & EPDM80BKFG'. Black coloured, compression moulded EPDM rubbers. Shore hardness between 60A & 80A. Tested in-radius size 1.0mm. For use with water up to 70°C.
0713.23/60 (shore hardness 60A). 0713.23/65 (shore hardness 65A). 0713.23/70 (shore hardness 70A). 0713.23/75 (shore hardness 75A). 0713.23/80 (shore hardness 80A). 0713.23/85 (shore hardness 85A). Black coloured, compression moulded EPDM rubber materials. Tested in-radius size 1.0mm. For use with water up to 85°C.
`SACHDEVA/EPDM-80`. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius 1.1mm. For use with water up to 23°C.
'E300'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'VI701/KTW'. Black coloured, injection moulded FKM 'O'-ring, shore hardness 70, tested in-radius 1.5mm. For use with water up to 85°C.
'Phardite D31'. Brown coloured, extruded hard/natural rubber material. Shore hardness 78. Tested in-radius size 0.9mm. For use with water up to 23°C.
‘NGP 60 T (Translucent – off-white), NGP 60 T/R (Transy Red), NGP 60 BK (Black), NGP 60 GY (Grey) & NGP 60 W (White)’. Extruded, platinum cured, silicone rubber tubing. Shore hardness 60. Tested in-radii sizes between 0.75mm & 1.5mm. For use with water up to 85°C
Bidet seat assembly with the flow controlled by a sensor actuated solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 1.75 bar. Maximum operating temperature 45°C.
A range of single-hole, single outlet (fixed (model 62816) or swivel (models 63407)) electronically controlled tap assemblies with brass bodies in various finishes (see models). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating members controlling both the flow and temperature for all models excluding 62816, which uses a mixer to control the temperature only with a single lever operating member. The spout outlets incorporate plastic aerators. All models (excluding 63407) incorporate a separate approved check valve cartridge on the inlet, verified by test (suitable for backflow protection against Fluid Category 2), The inlets of all models incorporate stainless steel strainers. Maximum working pressure 5.0 bar Maximum working temperature 60°C.
Single-hole, single outlet, swivel electronically controlled tap assembly with a brass body in various finishes (see model). Flow is controlled by a solenoid valve activated via an infra-red sensor and a ceramic cartridge with a single lever operating member controlling both the flow and temperature. The spout outlet incorporates a pull-out spray with a plastic aerator. The inlets incorporate approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 2), and a stainless-steel strainer Maximum working pressure 5 bar. Maximum working temperature 60°C.
Concealed WC dual flushing cistern with a BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two push button assembly for a 6 or 3 litre flush volume. Incorporating a servicing valve on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single hole, single outlet (fixed), combination tap assemblies (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator (SH-T9050N model) or a plastic flow straightener (all other models). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of in-line non-verifiable single check valve assemblies consisting of a spring loaded resilient trim single check valve cartridge housed within a brushed chrome DZR brass body. For use with copper pipe EN1057. Fitting also incorporates a stainless steel strainer For maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim in-line check valve cartridges housed in a DZR brass body. For use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of wall mounted, electrically heated catering water boilers. The boilers incorporate stainless steel storage tanks with stainless steel vent and overflow and silicon washers and gaskets, fed via a solenoid valve. The water is discharged via a self-closing tap with single lever operating member. The solenoid valve incorporates a plastic strainer at the inlet. Maximum working pressure 7.0 bar. Maximum operating temperature 98°C.
Single hole, single outlet (fixed, with swivel nozzle) bidet combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlets incorporate a plastic aerator. Supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assemblies with brass bodies (various finishes), incorporating a ceramic cartridge headworks and a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
A range of rotary cartridge headworks or ceramic cartridge headworks with plastic bodies and silicone seals. For insertion into specifically dimensioned bores. Models 38-7 and MD25FSF-2 are combined headwork and diverter cartridges, model M25SFS is a ceramic cartridge headwork. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of ceramic disc diverter cartridges with plastic bodies and silicon ‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Page 33 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
