‘Loxeal 58-11’. Yellow coloured anaerobic adhesive paste. This product is to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'PVCC125 & PVCC250 PVC Pipe Cement'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 24012024'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a ‘Type AB’ air gap arrangement (verified by test, suitable for backflow prevention against Fluid Category 5). Maximum working pressure 7.5 bar. Cold water supply only.
'122102001 Valve Body'. Black coloured, injection moulded PVC-U valve body. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (brass bodies - various finishes). Flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled manually with a single lever operating member. The spout outlet incorporates a plastic aerator. The inlets incorporate single check valve cartridges, however, the complete product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted single hole, single outlet (fixed) electronically controlled tap assemblies, (chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies, (Chrome plated - brass bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Bottom entry BS1212-4 (2016) compact type float operated inlet valve for WC flushing cisterns with a plastic body and adjustable float and a plastic flow regulator at the inlet. Maximum working pressure 10.0 bar. Cold water use only.
Range of Type TK spring loaded, resilient trim, in-line check valve cartridges. For insertion into specifically dimensioned bores. Maximum working pressure 10.0bar. Maximum operating temperature 65ºC.
Spring-loaded resilient trim in-line check valve cartridge with a plastic body, incorporating a stainless-steel spring and EPDM ‘O’-rings . For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spring-loaded resilient trim in-line check valve cartridges with plastic bodies, incorporating a stainless-steel spring and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Double check valve assembly consisting of two spring loaded resilient trim check valve cartridges housed in a nickel plated DZR brass body. The product also incorporates a lever operated isolation valve. For use with copper tube to BS EN 1057. Maximum working pressure 10 Bar Maximum operating temperature 85°C.
Tundish with a black plastic body and a straight through pattern. The product satisfies the requirements of an air gap to drain. Maximum operating temperature 65°C.
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly with a brass body (various finishes) incorporating a ceramic cartridge headwork with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop-up waste - not verified by test. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel nozzle) tap (chrome plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Flow regulator incorporating a plastic body and EPDM O-ring. Maximum operating temperature 65.0°C.
Range of ceramic cartridge headworks with plastic bodies incorporating silicone seals, for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of single hole, single outlet, (swivel), combination tap assemblies (chromium plated brass bodies), incorporating quarter turn ceramic disc headworks and single lever operating members. The outlet is a pull down spray type and incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 65°C
Range of single hole, single outlet (swivel) combination tap assemblies with (brass bodies -various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator.and a pull out spray feature. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection Maximum working pressure 7 bar. Maximum operating temperature 65ºC.
Range of single hole, single outlet fixed combination tap assemblies (brass bodies, various finishes – see models) quarter turn ceramic disc headworks with cross-top operating members. The spout outlets incorporate plastic aerators. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 300 of 509
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
