Range of gate valves with blue coloured epoxy coated ductile iron body and EPDM coated wedge. The valves operate via a non-rising spindle headwork with hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating an EDPM wedge and non-rising spindle with hand wheel operating member. Maximum working pressure 10.0 bar. Maximum working temperature 65°C
Range of screw down angle valves with brass bodies (chromium plated) and NBR ‘O’-rings with a dome type operating member. For above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperatures: model 510052 = 95°C and model 510060 = 85°C.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'DURACON® M25-44 WK2001, M90-44 WK2001 & M270-44-WK2001'. White coloured, injection moulded POM materials. For use with water up to 85°C.
'S' epoxy powder coating. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'SNC-EP09V1 - date 2009/12/1'. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 571 ES Blue 536'. Factory applied, blue coloured polyolefin coating. Apply as per manufacturer's instructions dated '08/2022'. Cure for 20 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoflor MFP 140 Primer and Smartcare Polyurea PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix Apcoflor MFP 140 Primer in a 1:1 mix ratio and apply as per Product Data Sheet ‘Version ‘0’, dated ‘Aug.2007’. Cure for 2 hours@25°C. Then mix and apply Smartcare Polyurea PW Coating as per Product Data Sheet ‘V01’, dated ‘8/2022’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'181019 Epoxy Phenolic RAL 5012'. Factory applied, blue coloured epoxy phenolic powder coating. Mix and apply as per manufacturer's instructions issued '15.01.2023'. Cure for 10 minutes at 200°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Polycor LP Gel Coat reinforced with Norsodyne H 13212 TAE laminating resin’. ‘NORSODYNE H 13212 BTAE laminating resin’ was added to the approval in July 2024. ‘Polycor LP Gel Coat’ is a brush or spray applied polyester resin gel coat, available in white or grey colours and is reinforced with Norsodyne H 13212 TAE or NORSODYNE H 13212 BTAE glass fibre laminate. Apply the brush grade as per manufacturer’s technical data sheet ‘7100’ dated 10.10.17 and apply the spray grade as per manufacturer’s technical data sheet ‘7200’ also dated 10.10.17. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interflon Paste HT1200'. Cream coloured ceramic paste. Apply as per manufacturer's instructions, document number 'IFUHT1200' dated 24/04/2017. Cure for 5 minutes@22°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass finish). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator and a stainless-steel strainer on the inlet. Maximum working pressure 8.0 Bar Maximum operating temperature 70.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chrome plated brass finish). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator and a stainless-steel strainer on the inlet. Maximum working pressure 8.0 Bar Maximum operating temperature 70.0°C
Spring loaded resilient trim check valve cartridge with a plastic body and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C
Spring loaded resilient trim in-line check valve cartridge with acetal body, incorporating a stainless steel spring, EPDM & silicone ‘O’-rings. To be housed in a specifically dimensioned body. Maximum working pressure 14 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of one piece water storage cisterns with a screened breather and over flow. Model 46714 iBoost+200 has a rectangular weir overflow Model 46712 iBoost+200 has a circular overflow Cold water only.
Range of self-closing headworks with stainless steel bodies to be housed in specifically dimensioned bodies. Maximum working pressure 8.8 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Single hole, single outlet (swivel) combination tap assembly with brass body (chromium plated), incorporating ceramic cartridge headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome and ‘supersteel’ plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The tap also incorporates a quarter turn ceramic disc headwork with a dome type operating member controlling the filtered water outlet. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (various finishes), incorporating ceramic cartridge headworks and single lever operating member. Spout outlet incorporates a plastic aerator and products are also supplied with lever operated pop-up wastes. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Page 24 of 56
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
