'LATILUB 75/4-20T NT:0080F2'. White coloured, injection moulded PBT material. For use with water up to 85°C.
'Siropol 8340'. Red coloured, injection moulded polyester resin. For use with water up to 45°C.
'MMP PE100 Pipe'. Black coloured (with blue coloured external stripes), extruded PE100 pipes manufactured from 'Sabic P6006' or 'Borouge HE3490-LS'. For use with water up to 85°C.
'GF PE100 Pipe (product codes beginning with '20014Y')'. Black coloured (with blue external stripes), extruded polyethylene pipe. For use with water up to 23°C.
'3301 black (330160415BLK)'. '3301 black (330130415BLK)' was added to the approval in November 2023. Black coloured, single sided polyethylene foam tapes with acrylic adhesive system. For use with water up to 23°C.
`Como-Pex Pipe`. Extruded, white coloured HDPE pipe. In April 2024, `Como-Pex Pipe`, extruded, black coloured HDPE pipe was added to the approval. Both pipes are for use with water up to 85°C.
'TP10847 Prisma Black'. Black coloured polyethylene material manufacture by rotational moulding. For use with water up to 70°C.
'HE3490-ELS-H'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
'Revolve 6405U Natural (appears white coloured) & Revolve M-1585 Black (black coloured)'. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
‘Revolve N-840 (HD3850) & Revolve M-750 DR Black’. Revolve N-840 (HD3850) is a white coloured polyethylene material & Revolve M-750 DR Black is a black coloured polyethylene material. Both are manufactured by rotational moulding. For use with water up to 85°C. Please note that ‘Revolve N-840 (HD3850)’ was formerly known as ‘Revolve N-840 (6850)’.
'XYRON WG732 AWY2266, WG732 AWY2269, WG732 AWY6628, WG722 AWY6627, W5002 AWY1208, W5002 AWY2267, W5002 AWY6629, W5002 AWY3326, WG722 AWY2261, WG732 AWY3325, WG722 AWY3324 & WG733 ABY3315'. Injection moulded, black, grey or beige coloured PPE materials manufactured in Thailand & China. For use with water up to 85°C.
‘Tecomid HT NT40 GR30 BK009 01 QW, Tecomid HT NT40 GR35 BK009 01 QW, Tecomid HT NT40 GR40 BK009 01 QW, Tecomid HT NT40 GR45 BK009 01 QW, Tecomid HT NT40 GR50 BK009 01 QW, Tecomid HT NT40 GR55 BK009 01 QW & Tecomid HT NT40 GR60 BK009 01 QW’. Black coloured, injection moulded glass-fibre reinforced PPA materials. For use with water up to 85°C.
'ALTECH PP-H FC 3013/500.01 GB13 NC0001-00 (1004864600000)'. Natural (appears white coloured), injection moulded PP-H material. For use with water up to 50°C.
'Hostalen PP H5416T'. White coloured (translucent), extruded polypropylene material. For use with water up to 60°C.
`Superfast Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'60 EPDM 334 black 60 ShA' (shore hardness 60) and '70 EPDM 335 black 70 ShA' (shore hardness 70). Black coloured compression moulded EPDM materials. Tested in-radius 1.07mm. For use with water up to 85°C.
‘40SIL310P, 45SIL310P, 50SIL310P(W), 55SIL310P, 60SIL310P, 65SIL310P, 70SIL310P, 75SIL310P & 80SIL310P'. Compression moulded, silicone rubber ‘O’ rings in natural, white, black, red, blue & yellow with tested in-radii sizes of between 0.5mm & 3.4mm. For use with water up to 85°C.
'XR0130012 (30SH), XR0140012 (40SH), XR0150012 (50SH), XR0160012 (60SH) & XR0170012 (70SH)'. Translucent, colourless, compression moulded silicone rubber materials. Shore hardness between 30 & 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'Bondchem WS27'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'Hetron 922'. Dark yellow coloured, injection moulded vinylester resin. For use with water up to 45°C.
Page 23 of 311
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
