Water filter and scale inhibitor comprising of a plastic filter head and plastic filter cartridge with an activated carbon block and sodium polyphosphate. The push-fit connections are for use with LDPE pipe (manufactured to DIN 8072). Maximum working pressure 5.52 bar. Cold water use only.
'ZX-9 Fusion Bonded Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HX' dated '2025.4.25'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EB-1003'. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer's instructions 'Fowry Powder-001' dated '2020.3.20'. For use with water up to 85°C.
'VETOPROOF EC720'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 84.8:15.2 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1104-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'VETOPROOF EC722'. Site applied, grey coloured, two-part epoxy coating. Mix parts A and B in a 85.4:14.6 weight ratio and apply three coats as per manufacturer's Method Statement 'MoS-SA-G1101-M-AK-09-23', dated '18 September 2023'. Cure first coat for 24 hours at 23°C, second coat for 24 hours at 23°C and third coat for 7 days at 23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'SINTA-GRP-01 Water Tank Panel'. Natural (appears off-white), hot press moulded GRP panel. For use with water up to 23°C.
'Hinton Easyjoint Silicone Grease (HSG200)'. Off-white coloured (opaque) silicone grease. Apply as per manufacturer's instructions. For use with water up to 65°C.
'Radilon A RCM4010RKC 306 BK'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 85°C.
'UP 5604 TP' (amber coloured) & 'UP- 4601 TPI' (pink coloured). Unsaturated polyester resin materials manufactured by hand lay-up. For use with water up to 50°C.
'Bingo HDPE Pipes 01'. Black coloured (with blue, external stripes), extruded HDPE pipe. For use with water up to 85°C.
'Bingo HDPE Fittings 02'. Black coloured, injection moulded HDPE fittings. For use with water up to 85°C.
'Hotace HDPE Black Pipe'. Black coloured (with blue stripes), extruded HDPE pipe. For use with water up to 80°C.
'Hengyuan PE100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'Fortron ICE 504L SD 3039 black (DW)'. Black coloured, injection moulded PPS material. For use with water up to 85°C.
'Ultrason® P 3010 MR grau 30373'. Grey coloured, injection moulded PPSU material. For use with water up to 85°C.
'PRO V200'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 7', dated '18/05/2022'. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ASIIR60WRC'. Black coloured, mould pressed isobutylene isoprene rubber. Shore hardness 65. Tested in-radius size 1.0mm. For use with water up to 85°C.
'E103 Sealing Ring'. Black coloured, injection moulded EPDM sealing ring. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 23°C.
'Corirubber 4070 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
'D0012'. Black coloured EPDM material manufactured by vulcanisation moulding. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'EPW50, EPW55, EPW60, EPW65, EPW70, EPW75 & EPW80'. Black coloured, injection moulded EPDM material. Shore hardness between 50 & 80. Tested in-radius 2.95mm. For use with water up to 65°C.
'ZXMFJ-50 SEALING'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius 1.25mm. For use with water up to 85°C.
'70EP505p'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'70NB502S'. Black coloured, compression moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'ergo 4207 (yellow coloured), 4205 (white coloured) & 4453 (green coloured)'. Anaerobic adhesives to be applied cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'E-Tupling Plastic Pipe Cement 125 ml ETSC125' & 'E-Tupling Plastic Pipe Cement 250 ml ETSC250'. Clear, transparent (un-pigmented) solvent cements, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TODAY TOOLS PVC SOLVENT CEMENT 125ML SC1' & 'TODAY TOOLS PVC SOLVENT CEMENT 250ML SC2'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TW Tools PVC Pipe Cement 125ml' & 'TW Tools PVC Pipe Cement 250ml'. Clear, transparent (un-pigmented) solvent cement, (intended to join PVC pipe and fittings). Apply as per manufacturer's instructions 'Rev00 08052025'. Cure for 20 days at 7°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AquaPure 2025'. Beige coloured tube manufactured by winding PET fibre and epoxy vinylester resin over a mandrel under heat and pressure, intended for the manufacture of bearings. For use with water up to 23°C.
Deck mounted pillar tap, (chrome plated brass) body. The flow is controlled by a solenoid valve which is actuated manually via rotary control switch using cross top operating members. Maximum working pressure 5.0 Bar Maximum operating temperature 85.0°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies, various finishes). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Depending on model the products are supplied with either a stainless steel braided PEX lined flexible hose assembly with 15mm spigot end connection or 10mm copper tail (see models). Maximum working pressure 8.0 Bar Maximum operating temperature 60.0°C
Bottom entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Floor mounted, single outlet (fixed) combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3)he shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator, and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Floor standing single hole, single outlet (fixed) combination tap assembly (chrome plated brass) body, incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to a shower outlet with a Type HC backflow protection device (verified by test - suitable for backflow protection against Fluid Category 3). The outlet to the shower incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C
Range of wall mounted, two hole, single outlet (fixed) combination tap assemblies (chromium plated brass), incorporating a non-rising spindle headwork with a single lever operating member. The temperature is controlled independently via a thermostatic cartridge incorporating a single lever operating member. Each inlet incorporates a combined washer and stainless-steel strainer, and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a self-cancelling diverter to shower outlet with Type HC device (verified by test - suitable for backflow protection against Fluid Category 3) and a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of floor mounted, single hole, single outlet, swivel combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The shower outlet incorporates a single check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator and the product is supplied with an approved shower hose and handset. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies (chrome plated brass) bodies. The flow is controlled via a solenoid valve activated via an infra-red sensor. The temperature is controlled independently via a thermostatic cartridge. The products incorporate approved check valve cartridges; however, the complete product has not been fully tested to demonstrate it provides backflow protection. The inlets incorporate a stainless-steel strainer. The products are supplied with spherical valves for both inlets. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C.
Range of shower kits with a shower hose, handset and shower rail. Maximum operating temperature 60 °C. Open outlet use only.
Range of shower sets with shower hose, handset and riser rail. Open outlet use only. Maximum operating temperature 65 °C.
T-type thermostatic blending valve with a nickel plated brass body and EPDM ‘O’-rings. The compression connections are for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of spring loaded single check valve cartridges comprising of a POM body and cap, stainless steel spring and EPDM gasket and O-rings. Max working pressure 10 bar. Max operating temperature 85°C.
Range of single check valve assemblies consisting of a single check valve cartridge housed within a DZR brass body. Compression connections on for use with popper pipe to BS EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 65°C.
Range of double check valve assemblies, incorporating two spring loaded resilient trim in-line check valve cartridges housed in DZR brass or nickel plated DZR brass bodies. Compression connection to be used with copper pipe EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Push to open, push to close ‘detent’ headworks with plastic bodies and EPDM ‘O’-rings. For insertion into specifically dimensioned bores. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Sequential ceramic cartridge headwork incorporating a plastic body and silicone seals. Maximum working pressure 5.0 Bar Maximum operating temperature 85 °C.
Single hole, single outlet (swivel) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-down spray type incorporating a push button. The connection to the pull-down hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides backflow protection. Maximum working pressure 5.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
| Product Identification | Surface finish | Inlet Dimension | Max Wrk. Pressure | Max Op. Temp. | Marking | Marking Location | All metals in the water pathway are on the 4msi positive list | Headwork | Fixing Type | Spout Outlet | Includes |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 193746 X XXX | VARIOUS | 1/2" BSP | 5.0 bar | 85 °C | PPI | REAR OF BODY | No | Ceramic cartridge | C-plate | Flow Straightener |
X XXX Denotes the following: First X: Different handle and the second, third & fourth XXX for different finishes: Handles: A (Lever type) Chrome – No suffix, Brushed brass – BGP, PVD Gold – PVD, Brushed Nickel – BN1, Gun Metal – GMG, Matt Black – MBK, Matt White – MWH, Stainless Steel – SS1, Black Chrome – BCP, Titanium – TIB and Antique Bronze – AB1.
Single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporates a stainless steel strainer and plastic flow strainer or a plastic aerator. The products are supplied with a click type waste. Maximum working pressure 10.0 Bar. Maximum operating temperature 65°C.
Single hole, single outlet (swivel) combination tap assembly with a brass body incorporating a quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic aerator or flow straightener with a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Page 214 of 227
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
