Range of wall mounted thermostatic blending valves with brass bodies (various finishes). Incorporating either 2-way ceramic disc diverters (2 on, 1 off) that also controls the flow (model DB3100.a.bbb) or with a ceramic disc headwork that controls the flow only to a single outlet (model DB3200.a.bbb.). Both incorporate lever type operating members. The temperature is controlled independently via a thermostatic cartridge with lever type operating members. Inlets incorporate approved check valve cartridges, however the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: 4925, 4925B, 4925G, 4923 & 4923G = 25.0 bar, 970W, 970WB, 970WG, 973W & 973WG = 16.0 bar. Maximum operating temperature 85°C.
Range of wafer and fully lugged butterfly valves with a black or blue epoxy coated ductile iron body and either lever type or handwheel operating members. Maximum working pressure: FM638, FM638B, FM639, DM638 & DM639 = 25.0 bar, F624, F624B, F625, DM925LW & DM925G = 16.0 bar. Maximum operating temperature 85°C.
Range of spring loaded, resilient trim, non-return valves with, stainless steel bodies and plunger with EPDM seals. Maximum working pressure 16.0 bar. Cold water use only.
Range of normally closed (NC), solenoid valves with plastic bodies and EPDM diaphragm. Models with push-fit connections are for use with copper pipe (manufactured to EN 1057) and PTFE pipe. The products incorporate a plastic or stainless steel filter on the inlet, (except for models with swivel nut, push-fit and nozzle inlets, as well as the 44.007.126 and 01.021.126 models) . The 44.007.126 model incorporates a Y-pattern stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperatures: Cold water use only, 65°C or 90°C for models marked with ℗ - Please consult model section for further details.
Range of normally closed (monostable) and pulse controlled/latching (bistable) solenoid valves with plastic bodies and integral stainless steel strainers. 50.005.101 model can also be supplied with an integral plastic strainer. To be installed in specifically dimensioned bodies. The 50.005.101 model can be supplied with or without a brass adaptor. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. 50.009.101 Bistable is for cold water use only.
Range of in-line full bore spherical valves with nickel plated brass bodies, chrome plated brass ball and either lever or ‘T’ handles (see model). The products are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: 30.0 bar (15mm-28mm) or 25.0 bar (35mm-54mm). Maximum operating temperature 99°C.
Range lever operated spherical valves with nickel plated brass bodies and chromium plated brass balls. The 1792 model compression connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of angled spherical valves incorporating a chrome plated brass body and ball with butterfly operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of seated gate valves with blue epoxy coated ductile iron bodies, bonnets and ductile iron wedges encapsulated in EPDM. All models have a handwheel operating member. Maximum working pressure 16 bar. Maximum operating temperature 80 °C
Range of gate valves with brass or DZR brass bodies, non-rising spindles and either hand wheel or lockshield operating members. The 4366 and 4363 compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure: 4.0 Bar. Maximum operating temperature: 60°C.
'NM 96 & NM 99 Ceramic Discs'. Off-white coloured, compression moulded ceramic discs. For use with water up to 85°C.
'Rubalit A 1896'. White coloured, dry-pressed ceramic disc. For use with water up to 85°C.
‘Ramco Ordinary Portland Cement’. Factory applied, grey coloured cement. Mix cement, sand & water in a mass ratio of 1:1.7:0.5 and apply as per manufacturer's instructions 'TSL/TSMD/DI/QA/TPI/DC/001', DATED '09.06.2025'. Cure for 4 hours@45°C then cure in open air for 28 days@33-39°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PROTEGOL EP Coating 32-99. Factory applied, two-component, yellow coloured epoxy coating. Mix Component A (resin) with Component B (hardener) in a volume ratio of 1.75:1.0 and apply as per manufacturer's TDS released '03/2025'. Cure for 24 hours at 23°C and then 24 hours at 70°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
EUROKOTE® 711.92BF bleu 5012, EUROKOTE® 711.92BF bleu 5015, EUROKOTE® 711.92BF bleu 5005 CR, EUROKOTE® 711.92BF bleu 5005 & EUROKOTE® 711.92BF bleu 5017. EUROKOTE® 711.92BF noir 9005. EUROKOTE® 711.92 bleu 5012, EUROKOTE® 711.92 bleu 5015, EUROKOTE® 711.92 bleu 5005, EUROKOTE® 711.92 bleu 5005 CR & EUROKOTE® 711.92 bleu 5017. EUROKOTE® 711.92 noir 9005. EUROKOTE® 711.92 BF Brun Rouge & 711.92 Brun Rouge Factory applied, blue, black or red coloured epoxy coatings. Apply as per manufacturer's technical data sheets dated 04/03/2025. Cure for 2 minutes@200°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Burasil Universal 9544/U'. Green coloured NBR/fibre gasket material manufactured by calandering. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'Grivory HT1VA-5 FWA black 9225'. Black coloured, injection moulded nylon material. For use with water up to 85°C.
‘4TECH 9S20000 W-A ABK’. Black coloured, injection moulded, unfilled PPO/HIPS material. Between February 2024 and April 2025, it was for use with water up to 23°C. Between May 2025 and February 2029, it’s for use with water up to 85°C.
Page 200 of 207
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
