Range of adjustable, bronze in-line pressure reducing valves. ½”, ¾”, 1” & 1¼” size have inspection ports on the outlet only. 1½”, 2”, 2½”, 3” AND 4” sizes have inspection ports on the inlet and outlet. The valves incorporate a stainless-steel strainer. Maximum inlet supply pressure 20.0 bar. Maximum outlet pressure 1.0 bar to 4.0 bar. Maximum operating temperature 70°C.
Range of adjustable in-line pressure reducing valves with bronze bodies, stainless steel strainers and manually operated pressure reducing mechanism. Outlet pressure adjustable between 1.5 to 6.0 bar. Maximum supply pressure 16.0 bar. Maximum operating temperature 60°C.
Range of normally open (L282 prefix models), normally closed (L182 models) or latching (61 suffix models) solenoid valves with either brass, nickel plated brass or stainless-steel bodies and an EPDM diaphragm. Please refer to model for maximum working pressure. Maximum operating temperature 85.0°C
Range of single lever or butterfly handle operated spherical valves with chrome plated brass bodies incorporating chrome plated brass ball. Maximum working pressures: see model below. Maximum operating temperature 23°C.
Range of spherical valves with brass bodies, stainless steel (SS304) balls and PTFE seats. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with nickel plated brass bodies, chrome plated ball and PTFE seats. Not supplied with operating member. Maximum working pressure 25.0 Bar Maximum operating temperature 90 °C.
Range of DZR brass isolation valves incorporating a chrome plated brass ball and PTFE seats. Maximum working pressure 16.0 Bar Maximum operating temperature 85 °C.
Range of angled spherical valves with (brass bodies - various finishes), PTFE seats and NBR seals. Model Art. 1251 incorporates a stainless-steel filter. Maximum working pressure 10.0, 35.0 or 55.0 Bar (see models) Maximum operating temperature 90.0°C (Art. 1251 Cold water only)
Range of inline or angled screwdriver and lever operated isolation and servicing valves (See models), (chrome plated brass bodies) and ball, incorporating EPDM ‘O’-rings. For use with copper pipe manufactured to EN1057 Maximum working pressure: 10 bar. Maximum working temperature: 99°C.
Range of ‘EFFAST’ spherical valves with plastic bodies incorporating EPDM ‘O’-rings. For use with ABS pipe manufactured to BS 5391. Maximum working pressure: 15 Bar. Maximum operating temperature: Cold water use only.
Range of non-rising spindle gate valves with DZR brass or brass bodies, incorporating PTFE stem packing and gaskets and handwheel operating members. Maximum working pressure 16.0 Bar Maximum operating temperature 85°C
Range of non-rising spindle gate valves with DZR brass bodies. Handwheel operated. Maximum working pressure: 20.0 bar. Maximum operating temperature: 100°C.
GAER S12 Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
GAER S12 Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with brass bodies, incorporating a brass wedge. Valves are operated via a non-rising spindle headwork incorporating either a lockshield or handwheel operating member. Maximum working pressure 20.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with bronze bodies and wedges, brass spindle and PTFE seals. Valves are operated via a non-rising spindle headwork incorporating either a handwheel or lockshield operating member. Maximum working pressure 20.0 Bar Maximum operating temperature 95.0°C
Range of gate valves with blue epoxy ductile iron bodies, ductile iron wedge encapsulated in EPDM. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies, EPDM coated ductile iron wedge and EPDM seals. Valves are operated via a non-rising spindle headwork. Maximum working pressure 16.0 Bar Maximum operating temperature 100.0°C
Range of gate valves with pipe connector and flange adapter systems with ductile blue epoxy coated bodies, EDPM wedge and PTFE gaskets. The valves operate via a hand wheel. Maximum working pressure 16.0 Bar Maximum operating temperature 50.0°C
Range of bronze gate valves incorporating bronze wedges, non-rising stems. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies, non-rising spindles and hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
SD-GGV20/DZR & SD-9102 ranges of gate valves with either brass or DZR brass bodies and PTFE washers. Valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 or 20.0 Bar Maximum operating temperature 85.0°C
Range of compression stop valves incorporating brass bodies, rising spindle headworks and EPDM gaskets. For use with copper pipe manufactured to BS EN 1057 (15mm, 22mm and 28mm) or PE pipe manufactured to BS EN 12201-2 (20mm and 25mm). Maximum working pressure 10.0 bar. Cold water use only.
Range of angled isolation valves (brass bodies – various finishes), incorporating a non-rising spindle headwork or quarter turn ceramic disc headwork with a dome or single lever type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of stop valves with brass bodies, brass discs and stems. The valves operate via a non-rising spindle and are supplied with a wheel type operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of 2, 3 ,4 or 5 way manifolds incorporating brass bodies, stop valves and EPDM O-rings, to be used with copper pipe to BS EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Inlet control group with a DZR brass body, consisting of a pressure reducing valve and pressure relief valve (4.5, 6.0 or 8.0 Bar). The inlet incorporates a stainless-steel strainer, and the outlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The product is for use with copper pipe to BS EN 1057. Outlet pressure range of the pressure reducing valve is 1.0 to 4.0 bar Maximum working pressure 16.0 Bar Maximum operating temperature 85.0°C
Range of manually operated balancing valves with DZR brass bodies. Maximum working pressure: 20.0 Bar. Maximum operating temperature: 85.0°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
BT1420-DFM Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of scale inhibitors with chrome plated copper bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 10.0 bar. Cold water use only.
'KEPITAL F25-03 LOF NAT'. Natural (appears white), injection moulded POM material. For use with water up to 60°C.
'RELIBIT 1001 Coating'. Factory applied, black coloured bitumen coating. Apply as per manufacturer's Standard Operating Procedure & Guidelines 'RP/291', '203/2024, Revision 1', dated '1st April 2024'. Cure for 10 hours@35°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TS2160'. Factory applied, grey coloured, enamel coating intended to line glass fused steel tanks. Apply two coats as per manufacturer's Work Instructions 'AQ 10 07 Rev.1'. Fire for 10 minutes at 840°C. For use with water up to 23°C. This material is only approved for the firing conditions that appear on the approval. If the firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZCGJ-2025'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'ZC02250725' dated '2025.7.25'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ZC-2025HSR'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio and apply as per manufacturer's instructions 'ZC01250725', dated '2025.7.25'. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's Work Instructions 'WP-08-05 I', Issue '04', Revision '0', dated '22.08.2024'. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 430'. Factory applied, two-part, white coloured epoxy coating. Mix base and curing agent in a 4:1 volume ratio and apply as per manufacturer's PDS dated 'December 2024'. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NEMA G10'. Green/yellow coloured, hot pressed GRE material. For use with water up to 50°C.
'Sanibiw Dynamic'. Multi-layered, extruded hoses comprising of an off-white, transparent silicone inner layer, white, opaque PES yarn reinforcement layer and black coloured, silicone outer layer. The inner layer has a tested in-radius size of between 0.4mm & 0.8mm. For use with water up to 85°C.
'Plustek PB305G33BK37 (black)'. Black coloured, injection moulded, glass reinforced PA material. For use with water up to 85°C.
'PLUSTEK PA100NT-F'. Cream coloured, injection moulded PA66 material. For use with water up to 85°C.
'GF30-NC024'. Light grey coloured, injection moulded, PA66+30%GF material. For use with water up to 85°C.
'XRC20B'. Black coloured, injection moulded PE material. For use with water up to 23°C.
'T-NO.100S-FD'. White coloured (translucent) PET mesh manufactured by weaving. For use with water up to 45°C.
‘2KPS EX3 Light Pink' & ‘2KPS EX3 Grey'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins. Apply and cure as per ’T Load’ cures set out in Table B4 of European Technical Assessment ‘ETA 16/0884’, dated ‘22/04/2025’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 16/0884’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
‘JCP PURE EPOXY RESIN JF375E'. Site applied, two-part (resin & hardener is automatically mixed in a 3:1 volume ratio through dispensing nozzle) anchor resins, available in light pink or grey colours. Apply and cure as per ’T Load’ cures set out in Table B3 of European Technical Assessment ‘ETA 17/0011’, dated ‘30/01/2023’. For use with water up to 65°C. If the cure conditions are varied from those specified in ’T Load’ cures set out in set out in Table B3 of European Technical Assessment ‘ETA 17/0011’ then the materials are not covered by the scope of the approval. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'EPDM 70.54-02 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EPDM 70.54-02 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Flexrubber EW70 gaskets'. Black coloured, compression moulded EPDM rubber gaskets. Shore hardness 70. Tested in-radius size between 1.53mm & 4.01mm. For use with water up to 23°C.
Page 199 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
