'EBYK' Georgios Peftitselis S.A. Enamel Coating'. Factory applied, blue coloured enamel coating. Apply as per manufacturer's data sheet 'MS1555A' dated 12-10-18. Cure for 14 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SGPAM-CN-WB01 - Black'. Factory applied, black coloured water based coating. Apply as per manufacturer's Technical Data Sheet 'PAMPIPE-TDC-WA04'. Cure for 30 min at 50°C plus 7 days at 23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CEC-GFS Enamel, Black Blue RAL5004'. Factory applied, blue/black (appears black) coloured, enamel coating. Apply as per manufacturer's instructions 'ZZ-Ins001', dated '2021.01.01'. GFS-G base glaze: dry for 15 Minutes at 200°C then fire for 12 minutes at 870ºC. GFS-S surface glaze: dry for 15 Minutes at 200°C then fire for 10 minutes at 830ºC. For use with water up to 85°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempadur 35560 Light grey (10500), Light red (50900) & Cream (20320)'. Factory applied, grey, light red coloured & Cream, two-component epoxy coatings. Each colour can be used as a base or topcoat and as a two-coat system. Mix base and curing agent in a 6.8:2 volume ratio. Apply Light Grey and Light Red as per manufacturer's Application Instructions issued 'November 2019'. Apply Cream as per manufacturer's Product Data Sheet dated 'December 2023'. Cure Coat 1 for 16 hours@20°C. Cure Coat 2 for 7 days@20°C. Between December 2022 and November 2024, the Light Grey and Light Red were for use with water up to 40°C. Between December 2024 and December 2027, Light Grey and Light Red are for use with water up to 60°C. The Cream coating was added to the approval in May 2025 and is for use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Welmortar-III'. Factory applied, grey coloured cement mortar. Mix cement, sand and water in a mass ratio of 2:3:0.85. Apply as per manufacturer's Standard Operating Procedure 'WDIPL/QA/WI/14A', revision '0', dated '01.10.2021'. Cure for 21 days at 30°C & 70% humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Tankguard DW White’ & ‘Tankguard DW Grey’. Site applied, two-part epoxy coatings. ‘Tankguard DW White’ may be used as a one-coat or two-coat system. ‘Tankguard DW Grey’ may be used as a one-coat or two-coat system. ‘Tankguard DW White’ & ‘Tankguard DW Grey’ may be used as a two-coat system, with either White or Grey as the water-contact coat. ‘Tankguard DW White’ & ‘Tankguard DW Grey’ each comprise of two parts (A & B) which are to be mixed in a volume ratio of 2:1 before applying as per manufacturer's Application Guide issued '17 October 2022'. Cure each coat for 7 days@23°C. For use with water up to 23°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval, then the materials are not covered by the scope of the approval.
'Tiefill'. Site applied, grey coloured cementitious repair mortar. Mix Tiefill with water in a weight ratio of 9.4:1 and apply in accordance with manufacturer’s instructions for use 'bulletin no. TFILL/031/003, issued 'July 2020'. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ULTRAMID® A218W V30 Natural-C’ (natural, appears off-white) & ‘ULTRAMID® A218W V30 Black-C’ (black coloured). Injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'Sierra PE-100 pipes'. Blue coloured, extruded PE-100 pipes. For use with water up to 65°C.
'Iglidur® UW160 Bearing'. Grey coloured, injection moulded PE bearing. For use with water up to 85°C.
'Kingbull PE100 Blue Fitting (391740)'. Blue coloured, injection moulded polyethylene fitting. 'Kingbull PE100 Black Fitting (0103208)'. Black coloured, injection moulded polyethylene fitting. Both for use with water up to 65°C.
'P600 BL & P301E BL'. Black coloured, extruded polyethylene pipes. For use with water up to 23°C.
'GPS Black PE100 Type V Pipe'. Black coloured, extruded PE100 pipe. For use with water 23°C.
'Topline PE100 HDPE Electrofusion/Butt Fusion Fitting'. Black coloured, injection moulded, PE100 (HDPE) fitting. For use with water up to 23°C.
'S-Ion PE100 Fittings'. Blue coloured, injection moulded PE100 fittings. For use with water up to 65°C.
'GPS Excel Black PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'PPE HY3140G'. Black coloured, injection moulded PPE material. For use with water up to 85°C.
'Aquatherm Green' range of extruded, polypropylene pipes, for use with water up to 85°C. (1) Aquatherm Green Pipe. Single layered, green coloured polypropylene pipe. The SDR11S pipe has four, blue longitudinal stripes on the exterior of the pipe. (2) Aquatherm Green Pipe (formerly named Fusiotherm Fibre Composite Pipe). Triple layered pipe consisting of a light green coloured polypropylene inner layer, glass fibre reinforced, polypropylene middle layer and light green coloured polypropylene outer layer. The pipe has dark green stripes on the exterior of the pipe.
'COD.2011'. Black coloured, injection moulded polypropylene compression fitting. For use with water up to 23°C.
'Thermocomp MB006SXP-BK1A994' (black coloured). Injection moulded polypropylene material. For use with water up to 85°C.
Page 190 of 508
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
