Range of balancing valves with DZR brass bodies. Maximum working pressure 25.0 Bar. Maximum operating temperature 100°C.
Range of magnetic & electrolytic scale inhibitors with nickel plated copper bodies, for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 12.0 bar. Cold water use only.
Range of domestic, salt regenerated ion exchange water softeners. Maximum working pressure 6.0 bar. Cold water use only.
'KOCETAL K300, K500 & K700'. Off-white coloured (opaque), injection moulded acetal materials. For use with water up to 85°C.
'K100'. Off-white coloured, injection moulded POM material. For use with water up to 85°C.
'ELECTROLINE ES 1212'. Factory applied, white coloured, two-component, solvent -free epoxy coating. Mix base and hardener in a 2:1 volume ratio and apply as per manufacturer's TDS 'ECL/ TDS / ES1212', issue date '2-Feb-14', version '0'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per manufacturer's Technical Data Sheet 'TWJ-H-453', 'Edition A1', dated '01/12/2023'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purethane NXT. Factory applied, off-white coloured, two-component Polyurethane coating. Mix resin and activator in a 2.5:1 volume ratio and apply as per manufacturer's 'APP-CA-NXT-Rev 04', dated '01.04.2023'. Cure for 7 days@23°C. For use with water up to 35°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Deep Seal Liquid Epoxy Paint'. Factory applied, two-component epoxy paint available in red/brown, grey, blue & white colours. Mix base and activator in a volume ratio of 3:1 and apply as per manufacturer's instructions 'DI/FG/2024/056', dated '25/04/2024'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Alesta Vanguard Blue Epoxy Powder EE80005001723’. Factory applied, blue coloured epoxy powder coating. Apply and cure as per manufacturer’s TDS version '22/01/2015'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Electrocement type CEM III A'. Factory applied, grey coloured slag cement mortar. Mix cement, sand and water in a mass ratio of 0.6:1.0:0.22 and apply as per manufacturer's work instructions 'WP-08-05 I', issue '04', rev. '0', dated '22.08.2024'. Cure for 28 days at 20°C - 22°C OR 24 hours@27°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Cicoprime®25 Primer and Cicoshield®PW100 Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply Cicoprime®25 Primer in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated October 2023. Cure for 2 hours@25°C. Then mix Cicoshield®PW100 Coating in a 1:1 ratio and apply as per Technical Data Sheet ‘version 1.1’, dated August 2024. Cure for 1 minute@25°C. For use with water up to 85°C.
'61300 EPOXY TB BT BLEU 5005'. Factory applied, blue coloured epoxy powder coating. Spray apply as per manufacturers TDS dated '15/2/2019'. Cure for 20 minutes@160°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SMS-FBE-Blue'. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s TDS 'Document Code 53', 'Publication No 5', dated 01.03.2024. Cure for 35 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikagard® 1816 (formerly known MasterProtect® 1816)'. Site applied, grey coloured (once applied), two-component Epoxy polysulfide coating. Mix parts A & B in a 78:22 weight ratio and apply coat 1 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 1 for 9 hours@25°C. Mix parts A & B in a 78:22 weight ratio and apply coat 2 as per manufacturer’s general method statement ‘MS - AD - Sikagard®-1816-01/2024’ and PDS '020303000000002044 Version 01.01', dated April 2024. Cure coat 2 for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Unitec 300 Green'. Green coloured compressed fibre gasket material manufactured by calendaring. For use with water up to 23°C. For use only as a gasket material having been tested at a reduced surface area to volume ratio.
Klingersil C-4430 plus. NBR fibre gasket material, manufactured by calendaring, which is red on one side and beige on the other side. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'POLYPOL-1023'. Beige coloured GRP rein manufactured by hand lamination. For use with water up to 65°C.
'VYDYNE AG7K-1001'. Light grey coloured, injection moulded PA66 material. For use with water up to 70°C.
'ULTRAMID® F3EG10 AQUA SW23285'. Black coloured, injection moulded PA6.1 material. For use with water up to 85°C.
'PC IR2200, Housing'. Clear (transparent), injection moulded polycarbonate housing component. For use with water up to 65°C.
'Veradel AG-330 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'Veradel AG-320 NT'. Light brown coloured, injection moulded polyethersulfone material. For use with water up to 85°C.
'ELYDAN'. Black coloured (with blue stripe), extruded HDPE pipe. For use with water up to 40°C.
'+GF+ Hakan HDPE PE100 Pipes'. Extruded PE100 pipes which are either blue coloured or black coloured (with blue stripes). For use with water up to 23°C.
'BR-PE-100 Fittings'. Black coloured, injection moulded PE100 fittings. For use with water up to 60°C.
'DELAV HDPE Pipe PE100' and 'DELAV HDPE Pipe PE100-RC'. Black coloured (with blue stripes), extruded PE pipes. For use with water up to 23°C.
'STAR Spigot Fittings'. Black coloured, extruded PE100 fitting. For use with water up to 60°C.
'GY-PEX-b(60-95)'. White coloured (translucent), extruded PEX hose. For use with water up to 85°C.
'Uponor Aqua Pipe'. Extruded, multi-layered PE-X pipe comprising of an off-white inner layer, black middle layer and white outer layer. For use with water up to 70°C.
'TORELINA® A670MWR1B'. Dark grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Visulfon' range of injection moulded PPSU materials which includes grades: K002 A8Y-G0048 (off-white). K002 BK001 (black). B002 NC001 (natural, appears amber). B002 BK001 (black). B002 A8Y-G0048 (off-white). For use with water up to 85°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'AquaTerra SDR 6 PP-R Pipes'. Green coloured, extruded PP-R pipes. 'AquaTerra SDR 7.4 PP-R Pipes', green coloured, extruded PP-R pipes were added to the approval in September 2024. All pipes are or use with water up to 85°C.
'+GF+ Hakan Aquasystem Faser Composite Stabil Pipe'. Multi-layered, extruded PPR pipe consisting of a white coloured inner, green coloured middle and white coloured outer layer. The following multi-layered, extruded PPR pipes were added to the approval in April 2025: Green coloured inner, green coloured middle and green coloured outer layer. Beige coloured inner, green coloured middle and beige coloured outer layer. Grey coloured inner, green coloured middle and grey coloured outer layer. For use with water up to 85°C.
'ISOGLASS H8C 4036U NA'. Cream coloured, injection moulded polypropylene material. For use with water up to 85°C.
'PTFE G300 Seat'. White coloured, extruded PTFE seat component. For use with water up to 85°C.
'Hepworth uPVC Pressure pipe'. Grey coloured, extruded uPVC pipe. For use with water up to 50°C.
'Sylglas Plumber Fix Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SPIT ViPer XTREM'. grey coloured (once mixed), two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'VIPER XTREM | 2023-1'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TELCOR THL FGEB 80G NC'. Black coloured, calendered, natural rubber material. Shore hardness 80D. Tested in-radius size 1.2mm. For use with water up to 23°C.
'E7108 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'E7108 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'E70C397'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size between 0.25mm and 5.0mm. For use with water up to 85°C.
'EP11/7/4 BLK'. Black coloured, injection moulded EPDM rubber `O` rings & gaskets. Shore hardness 70. The ‘O’-rings have a tested in-radius size of 1.5mm. The gaskets have a tested in-radius size of 1.4mm. For use with water up to 85°C.
'EPDM B1-4710'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.55mm. For use with water up to 85°C.
'VULCAN VEE4 Bellow & Boot'. Black coloured, compression moulded EPDM bellows and boot components. Shore hardness 70. The bellows has an in-radius size of 3.0mm and the boot has an in-radius size of 0.9mm. For use with water up to 85°C.
‘ML57308’ Black coloured, compression moulded EPDM rubber material. Shore hardness 75A. Tested in-radius size 1.0mm. Between April 2025 and April 2025, the material is for use with water up to 23°C. Between May 2025 and April 2029, the material is for use with water up to 60°C.
'OLDAL 460'. Black coloured, injection moulded EPDM material. Shore hardness 50. Tested in-radius size 1.2mm. For use with water up to 85°C.
'E7083AA'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
Page 175 of 225
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
