Range of spherical valves incorporating gunmetal bodies and EPDM ‘O’-rings. Valves can be either handle operated or actuator operated 24v or 230v and with or without return spring (see model). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of spherical ball valves with single lever or T-handle operating members, brass bodies (nickel plated) and chromium plated brass ball and PTFE washers. Maximum working pressure CP90 models = 40.0 bar. CP89 models = 25.0 bar. Maximum operating temperature 85.0°C
Range of plastic bodied inline, tee and angled spherical valves with EPDM ‘O’-rings and either lever or screwdriver operated (see model). For use with copper and PE-x pipe (manufactured to BS7291-3). Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
‘Z123’ range of gate valves with either brass or DZR brass (from October 2023) bodies and PTFE washers. Valves are operated via a non-rising spindle headwork. Maximum operating pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves incorporating either rising or non-rising spindle headworks and PTFE gaskets. The products are available as follows: Bronze body, bronze wedge and handwheel (132 prefix models). Bronze body, bronze wedge and handwheel (133 prefix models) or lockshield operating member (136 prefix models). Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.
Range of gate valves with bronze bodies with metal seats. The valves operate via a non-rising spindle headworks that incorporate a wheel type operating member or lock shield type (see models) Maximum working pressure 20.0 bar. Maximum operating temperature 85°C
Range of screw down drain valves having brass bodies and EPDM ‘O’-rings, for use with EN1057 copper tube R250 half hard. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of inline screw down stop valves with plastic bodies, non-rising spindle headworks and dome type operating members for use with PE-x (manufactured to BS7291-3) and copper pipe. Maximum working pressure/temperature: 10.0 bar @ 20°C and 10.0 bar @ 65°C.
Range of bedpan macerators. The flow is controlled by solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Commercial clothes washing machine having a flexible inlet hose and solenoid valve with filter at the inlet supplying a Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of commercial dish washing machines. Flow is controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The product is supplied with stainless steel or nylon braided EPDM inlet hose. Maximum working pressure 4.0 bar. Cold water use only.
Pressure vessel with spun fibre glass casing and polyethylene liner. Maximum working pressure 10.0 bar. Maximum operating temperature 70ºC.
'Delrin® FG500P NC010'. White coloured (opaque), injection moulded acetal material. For use with water up to 23°C.
'Delrin® FG911DP NC010'. White coloured (opaque), injection moulded acetal material. For use with water up to 23°C.
.TENAC-C 4590'. White (translucent) coloured, injection moulded acetal material. For use with water up to 85°C.
'ABS Grey 727 GR37 (grey coloured), ABS 727 White (white coloured), ABS 727 Grey (dark grey coloured) & ABS 727 Black (black coloured)'. ‘ABS 727 GR48 (grey coloured)’ was added to the approval on 2nd September 2022. Injection moulded ABS materials. For use with water up to 85°C.
'ME782 A1203 96%'. White coloured (opaque), ceramic pressure sensor manufactured by roll pressing. For use with water up to 23°C.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, grey coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV80502 / IW 80 (Hardener) Blue Epoxy Coating'. Factory applied, blue coloured, two-component epoxy coating. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 17 of 561
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
