'Loctite EA 109'. Factory applied, grey/beige coloured, heat cured epoxy coating. Apply as per manufacturer's TDS for Loctite ESP109 (product has changed name) dated July 2007. Cure for 2 hours@130°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Endoprene® 85-20’. Factory applied, two component, beige coloured, solvent free polyurethane coating. Mix and apply as per Technical Data Sheet dated '09/09/2019'. Cure for 8 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating Blue & Red'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'ZX-9-HY/NG' dated '2023-06-02'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Interline 975 White'. Site applied, two-part epoxy coating which can be applied as one coat or three coats. Mix parts A & B in a 2.2:1 and apply as per manufacturer's TDS 'Ref:4236', 'Issue Date: 04/02/2015'. When applied as a single coat, the coating must be cured for 14 days at 10°C. When applied as a three-coat system, the coating must be cured as follows: coat 1 = 24 hours@10 °C, coat 2 = 24 hours@10 °C & coat 3 = 14 days@10 °C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika MonoTop®-1010’, one-part cementitious bonding primer for use with ‘Sika MonoTop®-615’ one-part cementitious repair mortar. Mix ‘Sika MonoTop®-1010’ with tap water in the ratio of 25kg:5.25 litres. Apply as per manufacturer’s Product Data Sheet ‘020302020010000054, March 2021, Version 01.01’. Mix ‘Sika MonoTop®-615’ with tap water in the ratio of 25kg:3.8 litres and apply immediately to ‘Sika MonoTop®-1010’ as per manufacturer’s Product Data Sheet ‘020302040030000198, December 2021, Version 02.02’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LUBKOTE® E352, LUBKOTE® SG96(N96), LUBKOTE® SG98(N98)'. White coloured lubricants. Apply as per manufacturer's product data sheet 'YC20231201-1'. For use with water up to 85°C.
'ForTii Ace WX53-FC NA99001' (natural, appears beige in colour) & 'ForTii Ace WX53-FC BK00001' (black coloured). Injection moulded polyamide materials. For use with water up to 85°C.
'Acudel 22000 NT 15’ (natural - appears off-white coloured) & ‘Acudel 22000 BK 937’ (black coloured). ‘Acudel 22000 BK 937 ECHO RP’ (black coloured) was added to the approval in April 2025. Injection moulded PPSU materials. For use with water up to 85°C.
‘GFPP-(1) SFKP (2)’. White coloured, injection moulded, glass fibre reinforced PP material. (1) 2 digits represent the amount of fiberglass added to the material with a range of 5% - 50%. (2) is an internal code used to denote customer and is replaced with a 4 digit number between 0001 & 9999. For use with water up to 85°C.
'6EP1862 'O' ring'. Black coloured, injection moulded EPDM 'O' ring. Shore hardness 60. Tested in-radius size 0.89mm. For use with water up to 85°C.
'EPDM 9611 'O' rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radii sizes between 0.48mm & 2.0mm. For use with water up to 85°C.
'TJJH-EPDM gasket'. Black coloured, compression moulded EPDM gasket. Shore hardness 70. Tested in-radius size 1.2mm. Between April 2024 and March 2025, the gasket was for use with water up to 23°C. Between April 2025 and April 2029, the gasket is for use with water up to 65°C.
'557WE, 557WG & 557WM 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 60, 70 & 90. Tested in-radius size 0.85mm. For use with water up to 85°C.
'EP02971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM BW 5950 J 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 2.0mm. For use with water up to 65°C.
'IA 608/9735'. Grey coloured, injection moulded PVC material. For use with water up to 23°C.
'IR 348/9055'. Dark grey coloured, injection moulded PVC material. For use with water up to 23°C.
Range of single-hole, single outlet (fixed) electronically operated, tap assemblies (chrome plated brass). Flow is controlled by a solenoid valve activated by a touch sensor. The spout outlets incorporate plastic aerators. Max working pressure 8.0 bar. Max operating temperature 65°C.
Range of BS1212-4 (2016) float operated valves for WC flushing cisterns, bottom or side entry type with plastic or brass ½’’ BSP inlet. The inlet incorporates a strainer, Compact models incorporate a delay fill function. Maximum working pressure 10.0 bar. For use with cold water only.
Concealed WC dual flushing cistern with a side entry BS 1212-4 (2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure – 10.0 bar, cold water use only.
Page 154 of 201
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
