'Lavelle BUR165'. Red coloured, transfer moulded, silicone rubber gasket. Shore hardness 40A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'GFS Gas Flex Systems 543 Pipe Sealants'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/09/2022 v1.0'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Single hole, triple outlet (swivel) combination tap assembly (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with single lever operating member. Electronic controls allow the tap to dispense boiling, chilled or sparkling water. The vented models are supplied with a brass adaptor containing a plastic flow regulator and a combined EPDM washer and stainless-steel strainer, for installation on the mains cold water into the ceramic cartridge. They are also supplied with a stainless steel braided PEX lined flexible hose assembly and a stainless steel braided TPSiV lined flexible hose assembly both with ½” captive nut end connections for installation between the tap and a command centre, (which is not included as part of this approval). Maximum working pressure 5.0 bar. Maximum operating temperatures: Near boiling water circuit: 100°C. Ambient hot and cold (mixed) circuit: 65°C. Chilled/Chilled and sparkling circuit: Cold water use only.
Range of wall mounted, concealed, electronically controlled combination tap asselmblies (various finishes). The flow is controlled by a solenoid valve that is activated via an infra-red sensor which can be single or dual feed and incorporates lever operated isolation valves with stainless steel strainers. The spout outlet incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass or stainless-steel bodies) which are supplied with pre-mixed water. Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of check valve cartridges with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) over the rim (swivel nozzle) bidet combination tap assembly (chromium plated brass), incorporating ¼ turn ceramic disc headworks with cross top operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a lever type operated pop-up waste (not tested). Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of plastic aerators. Aerators which include ‘gpm max’ in the model name, incorporate a plastic flow regulator. Maximum operating temperature 60°C
Range of single-hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Models (23.790.xx1, 32.109.xx1 and 32.114.xx1) are supplied with lever operated pop-up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of pillar taps, (chrome plated, brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with metal back nuts. Maximum operating pressure 6 bar. Maximum operating temperature 85°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: See Models
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (black or chrome plated), incorporating ceramic cartridge headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes), incorporating ceramic cartridge headworks, with single lever or dome type operating members. The spout outlet incorporates a plastic aerator. Some models are supplied with a lever type pop up waste (see models) Other models are supplied with a permanently open waste set. Maximum working pressure 10.0 Bar Maximum operating temperature 70.0°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork and single lever operating member. The spout outlet incorporates a plastic aerator. Supplied with a click type waste. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (swivel) combination tap assemblies, (chrome plated brass bodies). Model 4E2318 incorporates a ceramic cartridge headwork with single lever operating member. Model 4E2319 incorporates quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate a flow straightener and is also supplied with an optional aerator. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of single-hole, single outlet, (swivel), combination tap assemblies (brass bodies – various finishes) incorporating quarter turn ceramic disc headworks with single lever operating members. Models (ASP2/CH, ASPQ2/CH & SLD2CH) incorporate ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature - see models.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes). Incorporating a quarter turn ceramic disc headworks with spring loaded return to the closed position controlling flow of the boiling water outlet and a ceramic cartridge headwork controlling flow from the hot and cold supply with dome type or lever type operating members (model V7C294 does not incorporate a ceramic cartridge headwork, for boiling water only). Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Single hole, single outlet, swivel combination tap assembly with brass body (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, double outlet (swivel) combination tap assemblies (chromium plated brass). incorporating quarter turn ceramic disc headworks with single lever operating members or non-rising spindle headworks and dome type or cross top operating members (see model). The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 129 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
