'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'TIY 001'. Grey coloured (opaque), compression moulded GRP panel. For use with water up to 23°C.
'GPS Excel Black PE100 Pipe'. Black coloured, extruded PE100 pipe. For use with water up to 23°C.
'Hydrothen PE 100 Black Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'WIN Spigot Fittings'. Black coloured, injection moulded PE100 spigot fittings. For use with water up to 60°C.
'GPS EXCEL NB Pipe'. Dual layered, extruded pipe consisting of a black coloured, PE100 inner layer and blue coloured, PE100 outer layer. For use with water up to 23°C.
'TP13444 Black'. Black coloured, rotomoulded, polyethylene material. For use with water up to 85°C.
'8108658 V0010_K LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'8108658 V0010_V LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'1024 Titan Bladder'. Clear (translucent), extruded TPU bladder. Shore hardness 87. Tested in-radius size 0.48mm. For use with water up to 80°C.
'TELCOR THL FGEB 80G NC'. Black coloured, calendered, natural rubber material. Shore hardness 80D. Tested in-radius size 1.2mm. For use with water up to 23°C.
'TRA-7073'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CHEMILINE AI060 FB 1304'. Black coloured NR & SBR material manufactured by calendaring. Shore hardness 76 D. Tested in-radius size 1.0mm. Between June 2023 and June 2025, the material was for use with water up to 23°C. Between July 2025 and June 2028, the material is for use with water up to 60°C.
'NBR N65WKZ'. Black coloured, injection moulded NBR rubber material. Shore hardness 59. Tested in-radius 1.0mm. For use with water up to 23°C.
'N65WKZ'. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
'Datkafix DF-43'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/02/2024 v1.1'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of push fit stop valves with white plastic bodies. Maximum working pressure/temperature: 10bar @ 20°C and 4 bar @ 60°C.
Floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates manual diverter to a shower outlet. The spout outlet incorporates an open outlet type spout. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure - 8 Bar. Maximum operating temperature - 65 °C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Side entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Sekisui F range of un-insulated GRP sectional cisterns. The larger cisterns have stainless steel internal bracing and UPVC pole supports. Insulated cisterns were added to the approval in March 2025. All cisterns are for cold water use only.
Ceramic cartridge headwork with a plastic body, incorporating a silicone rubber ‘O’ ring. Intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of ceramic disc headworks with brass bodies and NBR ‘O’-rings. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Range of deck mounted, two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc or a quarter turn compression washer headwork with various operating members (see model). The inlet of the quarter turn ceramic disc headwork incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model) Maximum working pressure 6 Bar. Maximum operating temperature 65 °C
Single-hole, single outlet, fixed combination tap assembly (chrome plated brass) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. The product is supplied with an approved click-type waste. Maximum working pressure 10.0 Bar Maximum operating temperature 60°C.
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, fixed combination tap assemblies (chrome plated brass bodies), incorporating quarter turn ceramic disc headworks with cross top operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with lever operated pop-up wastes. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, fixed combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with a click-type pop-up waste. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range single hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range single hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with a click type pop-up waste. Maximum operating pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet fixed combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop-up wastes. Maximum operating pressure 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, fixed, combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The products are supplied with click-type pop up wastes. Maximum operating pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever (Elysian models) or dome type (Milani models) operating member. The spout outlet incorporates a plastic flow straightener (Elysian models) or a plastic aerator (Milani models). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Single hole, single outlet (fixed) combination tap assemblies various finishes incorporating a ceramic cartridge headwork with various operating members. The spout outlets incorporate a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet fixed combination tap assemblies (brass body with various finishes), incorporating a ceramic cartridge headwork with either a single lever or cross top operating member. The spout outlets incorporate a plastic aerator. Products are supplied with PEX inner-lined grey plastic braided inlet hoses. Maximum working pressure 10 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single-hole, single outlet, (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet. Supplied with click waste outlet – verified by test. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (chromium plated brass) incorporating a single sequential cartridge that controls both the flow and temperature with a single lever operating member. The spout outlets incorporate a plastic flow straightener. All products are supplied with a plastic strainer and a spherical valve,brass adaptor, plastic flow regulator and brass flow regulator holder for installation on each inlet tail. The models ending in 610/610L are supplied with copper tails. All other models are supplied with stainless steel braided PEX lined flexible hose assemblies with ⅜” captive nut end connections and an additional fibre washer. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Floor mounted single hole, single outlet (fixed) combination tap assembly (brass bodies -various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge, non-rising spindle or quarter turn ceramic disc headwork with either a single lever, cross top or dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Page 126 of 209
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
