Range of wafer, lugged and double flanged type butterfly valves (with blue epoxy coated ductile iron bodies, and either a stainless steel or grey epoxy coated ductile iron disc with an EPDM liner. Maximum working pressure 16.0 Bar (DN50 to DN800) or 10.0 Bar (DN900 to DN1200)
Non-metallic materials and components comply with BS6920 at 60°C
Range of butterfly valves with blue epoxy coated ductile iron bodies and discs, and EPDM seals with handwheel gear operating members. Maximum working pressure – 10 bar or 16 bar, see models. Maximum operating temperature – 23°C.
Range of lever operated butterfly valves with blue epoxy coated cast iron bodies, stainless steel discs and EPDM ‘O’ rings and seals. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Wall mounted, concealed shower control valve with a brass body, incorporating a non-rising spindle headwork and EPDM O-rings. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of non-return valves housed within a blue epoxy coated ductile iron body. Maximum working pressure 16.0 bar. Maximum operating temperature 80ºC.
‘Aquacheck’ range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel springs and EPDM seals. Maximum working pressure 16 bar. Cold water use only.
Range of non-return, swing gate valves with gunmetal bronze bodies. Maximum working pressure 20.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of adjustable, in-line pressure reducing valves with gunmetal, bismuth red brass or stainless-steel bodies. The inlets incorporate a stainless-steel strainer. Maximum inlet supply pressure of 25.0 bar. Maximum outlet pressure in the range of 1.0-8.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of adjustable, in-line pressure reducing valves with gunmetal, bismuth red brass or stainless-steel bodies. The inlets incorporate a stainless-steel strainer. Models have a maximum inlet supply pressure of 25.0 bar. Maximum outlet pressure in the range of 1.0-8.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of adjustable, in-line pressure reducing valves with gunmetal, bismuth red brass or stainless-steel bodies. The inlets incorporate a stainless-steel strainer. Models have a maximum inlet supply pressure of 25.0 bar. Maximum outlet pressure in the range of 1.0-8.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of adjustable, in-line pressure reducing valves with gunmetal, bismuth red brass or stainless-steel bodies. The inlets incorporate a stainless-steel strainer. Models have a maximum inlet supply pressure of 25.0 bar. Maximum outlet pressure in the range of 1.0-8.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure reducing valves with DZR brass bodies. Maximum inlet supply pressure 25.0 bar. Outlet supply pressure is adjustable within the range of 1.5 bar to 6.0 bar. Maximum operating temperature 70°C.
Inlet control group consisting of an in-line pressure reducing valve (adjustable pressure - see model) and a pre-set expansion relief valve (pre-set pressure - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Compression connection to be used with copper pipe EN1057 only. Maximum supply pressure 10.0 bar. Maximum operating temperature 40°C.
Range of pilot operated pressure reducing valves with blue epoxy coated ductile iron bodies. The valves have an adjustable pressure reducing facility controlled via a pilot valve (with an operating range of 1 to 6 bar), with auxiliary components including stainless steel tubing, fittings and spherical valves. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of pre-set pressure relief valves (set at 3.0 bar) with nylon bodies, EPDM diaphragms and ‘O’-rings.
Non-metallic materials and components comply with BS6920 at 85°C
Range of latching solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings.. Maximum working pressure 10.0 Bar.
Non-metallic materials and components comply with BS6920 at 70°C
Range of stainless-steel spherical valves, incorporating a stainless-steel ball, PTFE seats and EPDM ‘O’-rings with single lever operating members. Maximum working pressure 63.0 Bar. Maximum operating temperature 23.0°C
“Ballofix®Lock” range of in-line hex key operated spherical valves with PTFE seals and EPDM ‘O’-rings. 3399300 & 3499300 models have a brass body. 3599300, 37199300 & 38199300 models have a DZR brass body. All models have a DZR brass ball (chromium plated). Maximum working pressures: 3399300, 3499300 and 3599300 models are 16.0 bar. 37199300 and 38199300 models are 25.0 bar. Maximum operating temperature 95°C.
‘3029’ range of lever operated spherical valves with chromium plated brass bodies and balls, incorporating PTFE seats and EPDM ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 99°C.
Range of bronze spherical valves, incorporating chrome plated brass balls, PTFE seats and EPDM O-rings. Model (BW-Q01) incorporates a single lever operating member. Model (BW-Q01B) incorporates a butterfly type operating member. Maximum working pressure 16 bar. Maximum operating temperature 85°C
Range of gate valves with ductile iron bodies (green epoxy coated) and EPDM coated ductile iron wedge. Maximum working pressure – 16.0 Bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of flanged gate valves with blue epoxy coated ductile iron bodies and EPDM O-rings and disc. The valves are operated via a non-rising spindle headwork with a wheel type operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 80°C
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM encapsulated wedge. The gate is operated via a hand wheel operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Double flanged, gate valve with blue epoxy coated ductile iron body and EPDM coated wedge and handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 71°C
Range of gate valves with (blue epoxy coated) iron ductile bodies. The valves operate via a hand wheel operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of gate valves with a non-rising spindle with a handwheel operating member. All models have brass body and brass wedge. For use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of unvented monobloc groups consisting of an in-line pressure reducing valve (PRV) (adjustable between 2.7 and 3.3 bar or 3.2 and 3.8 bar - see model) and a pre-set expansion relief valve (SRV) (pre-set at either 4.5, 4.75, 5.0, 6.0 or 8.0 bar - see model) housed in a DZR brass body with an EPDM rubber diaphragm. The product incorporates a check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The expansion relief valve is fitted with a rotary type easing gear and the products are for use with copper pipe (manufactured to EN1057). Maximum inlet supply pressure 10.0 bar. Maximum operating temperature 85°C.
'POM-020 Black'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'JSGL-OPC (N)'. Factory applied, grey coloured Ordinary Portland Cement. Mix and apply as per manufacturer's work instructions 'JSGL/WI/14', issue '02', revision '00', dated '29.09.2018'. Cure for 4 hours@45°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ascent-01'. Factory applied, grey coloured, Portland cement mortar. Mix sand, cement and water in a weight ratio of 1:1:0.35 and apply as per manufacturer's user instructions 'doc: Ascent-01', 'vision: A08052023', dated '2023-05-08'. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LOCTITE GeoSpray Mortar'. Site applied, grey coloured, geopolymer cementitious material. Mix 300g of powder with 60ml water and apply as per manufacturer's instructions 'V: 09.06.2022'. Cure for 96 hours@3°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GRP-GEI-Fiberstrong Pipe'. GRP pipe, manufactured by filament winding, which is light green coloured on the outside and beige coloured on the inside. For use with water up to 50°C.
‘BESLUX FLUOR FLUID 06’. Transparent, colourless PFPE lubricating fluid. Apply as per manufacturer’s instructions. For use with water up to 85°C.
'VESTAMID LX9042 NC'. White coloured, injection moulded PA12 material. For use with water up to 85°C.
'PANG30'. Black coloured, injection moulded, glass fibre reinforced nylon material. For use with water up to 85°C.
`Simona Peak Pipe Systems PE100 Pipe`. Black coloured, extruded PE100 pipes. For use with water up to 23°C.
'Supreme PE Pipe TSIL G'. Black coloured (with blue stripes), extruded PE 100 pipe. For use with water up to 60°C.
'TP12939 Natural'. Natural (appears off-white) polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'TP12978 Black'. Black coloured, polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'Mungo Injection System MIT800RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'Jun-23'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'EPDM50BKWS, EPDM55BKWS, EPDM60BKWS, EPDM65BKWS, EPDM70BKWS, EPDM75BKWS & EPDM80BKWS'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'JJSXEPDMIRHD50 (shore hardness 50) & JJSXEPDMIRHD70 (shore hardness 70)'. Black coloured, compression moulded EPDM materials. Tested in-radius size 0.99mm. For use with water up to 23°C.
'Water Life'. Black coloured, compression moulded NBR 'O' rings. Shore hardness 70. Tested in-radius size between 0.75mm & 1.25mm. For use with water up to 23°C.
'Effast Tite'. Site applied, blue coloured solvent cement. Apply as per manufacturer's instructions '6310522/20'. Cure for 30 minutes@12°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, single-hole, single outlet, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The products incorporate a stainless steel braided PEX lined flexible hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Page 124 of 232
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
