Range of spherical valves incorporating DZR brass (Art.59) or nickel-plated brass (Art. 89) bodies and chromium plated brass balls. For use with copper to BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of press fit spherical valves with DZR brass bodies and balls with EPDM O-Rings. Joints are achieved by the use of a press fitting tool. For use with Multi-layered Pert/Al/Pert pipe compliant to EN21003-2 Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Range of quarter turn, lever handle or butterfly operated spherical valves with nickel plated brass bodies, chrome plated brass balls and PTFE seals. For use with copper pipe BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with brass bodies and stems, incorporating chrome plated brass ball and EPDM O-rings and single lever operating members. Maximum supply pressure 24.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Multi-operational spherical valve with DZR brass body, incorporating (chromium plated) brass balls and PTFE seats. The product incorporates two flow control levers and multiple outlet connections. Compression connection to be used with copper pipe EN1057 only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of handwheel operated gate valves with brass bodies, gate & PTFE seals, for use with copper tube manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with blue epoxy coated ductile iron bodies and EPDM encapsulated wedge. The gate is operated via a hand wheel operating member. Maximum working pressure 16.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of pressure reducing valve assemblies with DZR brass bodies incorporating a spherical valve, a pressure gauge and 2 inline check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Models TVAP250001 & TVAP250005 also incorporate a water meter port. Maximum supply pressure 16 bar. Outlet pressure setting is adjustable in the range 1.5 to 6 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 8.6 bar. Cold water use only.
'PA-727 CM1404 White & PA-727 CM1405 Grey'. White or grey coloured, injection moulded ABS materials. PA-727 CM1404 White is for use with water up to 85°C. PA-727 CM1405 Grey is for use with water up to 23°C.
`9011 modified bitumen anticorrosive coating`. Factory applied, black coloured bituminous coating. Apply as per manufacturers user instructions 'File No.: SDC-0051', 'Vison: A1', dated '2021-03-01'. Cure for 7 days@23°C. For use with water up to 35°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ZX-9 Zhenxin Epoxy Powder Coating'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's 'Preparation and Curing Conditions' instructions reference 'ZX-9-1', dated '2024/02/26'. Cure for 30 minutes@180°C. For use with water up to 85°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SYM-218'. Factory applied, grey coloured, two-part epoxy coating. Mix parts A & B in a 4.3:1 ratio and apply as per manufacturer's TDS 'XYJSMS001' dated '2023-01-10'. Cure for 168 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
KARUMEL EX4413-F103. Factory applied, fusion bonded, epoxy powder coating available in blue or red. Apply and cure in accordance with 'Application Guide KARUMEL EX4413-F103', issue 'KCSA-230201', dated February 2023, (curing as per Section 3.6). For use with water up to 85°C.
'SGPAM-CN-WB01'. Factory applied, blue coloured water based coating. Apply as per manufacturer's TDS 'PAMPIPE-TDC-WA04', version '4', dated '16/11/2022'. Cure for 30 minutes@50°C. For use with water up to 23°C. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TYSN-01'. Factory applied, grey coloured cement. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio and apply as per manufacturer's instructions file number 'GB1752023', edition 'A0', dated '2023-06-11'. Cure for 24 hours at 25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ductan 087'. Factory applied, bright blue coloured, modified PE powder coating. Apply as per manufacturer’s application guidance document ‘issue 1’, dated 3rd August 2018. No curing is required. For use with water up to 60°C.
'CORROPOXY-FGE400'. Factory applied, red coloured, two-component epoxy coating. Mix and apply as per manufacturer's Application Procedures 'CPE/ FGE-400/Procd. /02', 'issue no - 03', dated '12.05.2022'. Cure for 30 minutes@45°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'AYYTCM-01'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per MSDS '20170508A1'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Luberpox – 2K – DS-Lackfarbe IV80, Wilo Grün nach Muster/IW80 Hardener (green coloured) & Luberpox – 2K – DS-Lackfarbe IV80, RAL 9011 Graphitschwarz/IW80 Hardener (black coloured). Factory applied epoxy coatings. Mix in a 5:1 weight ratio and apply as per Berger-Lacke Technical Data Sheet (rev. 41-06.11.2023). Cure for 7 days at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LZYX002'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per Instruction Sheet '201 8 07 0', revision 'A2'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-BFS'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14B', revision '01', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RAX Cement Mortar'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instructions 'WI-PRD-08', rev. '00', dated '01.02.2023'. Cure for 24 hours@28°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flexseals 163 Green'. Green coloured fibre sheet material manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/material having been tested at a reduced surface area to volume ratio. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
‘Pilotpack 3480, 5035, 3435, 4040, 7099, 3408, 3410 & 5020’ range of gland packings. 3480 & 3435 are dark grey coloured, graphitised PTFE based. 5035 is yellow & black coloured, graphitised PTFE/aramid based. 4040 is grey coloured, graphite based. 7099 is white coloured, acrylic/PTFE based. 3408 is white coloured, lubricated PTFE based. 3410 is white coloured, lubricated PTFE based. 5020 is light yellow coloured, lubricated aramid based. All grades are for use with water up to 85°C. For use only as gland packing material having been tested at a reduced surface area to volume ratio.
'SUPIC-710PT GRP'. Beige coloured GRP material manufactured by hand lay. For use with water up to 23°C.
'SYH-PH215'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'EcoPaXX Q-DWX12 BK00002'. Black coloured, injection moulded polyamide material. For use with water up to 85°C.
'Pemaron660G6W NC01'. Natural (appears off-white), injection moulded, glass-reinforced PA66 material. For use with water up to 85°C.
'AGRULINE PE100RC Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'TP13270 Green'. Green coloured polyethylene material manufactured by rotomoulding. For use with water up to 70°C.
‘LURANYL® KR 2402 TW 35061, LURANYL® KR 2403 G4 TW 26343 & LURANYL® KR 2403 G6 TW 26343’. Black coloured, injection moulded polyphenyleneoxide/polystyrene materials. In May 2025, ‘LURANYL® KR 2403 G2 TW GY4090-24’ & ‘LURANYL® KR 2403 G6 TW GY4040-24’, dark grey coloured, injection moulded polyphenyleneoxide/polystyrene materials were added to the approval. All grades are for use with water up to 85°C.
'Powertherm PP-R pipe'. Green coloured, extruded PP-R pipe (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'POWERtherm PP-R Fittings'. Green coloured, injection moulded PP-R fittings (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
'M1600'. White coloured, injection moulded PP material. For use with water up to 65°C.
'Borstar® RA150E'. Natural (appears off-white) polypropylene material for injection moulding and extrusion purposes. For use with water up to 85°C.
'PTFE2215 seal'. White coloured (opaque), compression moulded PTFE seal. For use with water up to 85°C.
'Bush (25122200)'. Dark grey coloured, extruded NEP-25%carbon/PTFE component. For use with water up to 85°C.
'STAR PIPE VULGARI.EPE PVC PRESSURE PIPE EN1452'. Black coloured, extruded PVC pipe. For use with water up to 23°C.
'PRO V500 V4'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions version '9', dated 'October 2022'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 100'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions ref. no. 'rev5' dated 04/06/218. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'vinyl eco/EASF'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 113 of 204
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
