'8108658 V0010_V LLDPE'. Blue coloured, roto-moulded LLDPE material. For use with water up to 23°C.
'Visulfon' range of injection moulded PPSU materials which includes grades: K002 A8Y-G0048 (off-white). K002 BK001 (black). B002 NC001 (natural, appears amber). B002 BK001 (black). B002 A8Y-G0048 (off-white). For use with water up to 85°C.
'Amodel DW-1140 BK 938 & Amodel DW-1150 BK 938'. Black coloured, injection moulded PPA materials. For use with water up to 85°C.
'+GF+ Hakan Aquasystem'. White or green coloured, injection moulded PPR fittings. For use with water up to 85°C.
'+GF+ Hakan Aquasystem Faser Composite Stabil Pipe'. Multi-layered, extruded PPR pipe consisting of a white coloured inner, green coloured middle and white coloured outer layer. The following multi-layered, extruded PPR pipes were added to the approval in April 2025: Green coloured inner, green coloured middle and green coloured outer layer. Beige coloured inner, green coloured middle and beige coloured outer layer. Grey coloured inner, green coloured middle and grey coloured outer layer. For use with water up to 85°C.
‘Formül, Aquapa, Aquaplast, Foraqua & Aquapipe Green PP-R Pipe'. Green coloured, extruded PP-R pipes. For use with water up to 85°C.
‘Formül, Aquapa, Aquaplast, Foraqua & Aquapipe Green PP-R Fittings'. Green coloured, injection moulded PP-R fittings. For use with water up to 85°C.
'+GF+ Hakan Aquasystem'. Extruded, PPRC pipes available in green, white or beige colours. For use with water up to 85°C.
'ISOGLASS H8C 4036U NA'. Cream coloured, injection moulded polypropylene material. For use with water up to 85°C.
'Ultratape Silcone Repair Tape'. Black coloured, extruded silicone repair tape. For use with water up to 85°C.
'RAMSET ChemSet 801 Xtrem XC²'. Grey coloured coloured, two-component vinylester resin anchor. Part A is a cream coloured paste and Part B is a dark grey coloured paste, supplied in a pre-weighed cartridge (10:1 volume ratio). Apply as per manufacturer's TDS 'August 15, 2018'. Cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TELCOR THL FGEB 80G NC'. Black coloured, calendered, natural rubber material. Shore hardness 80D. Tested in-radius size 1.2mm. For use with water up to 23°C.
'E70C397'. Black coloured, compression moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size between 0.25mm and 5.0mm. For use with water up to 85°C.
'EP11/7/4 BLK'. Black coloured, injection moulded EPDM rubber `O` rings & gaskets. Shore hardness 70. The ‘O’-rings have a tested in-radius size of 1.5mm. The gaskets have a tested in-radius size of 1.4mm. For use with water up to 85°C.
'EPDM B1-4710'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size 1.55mm. For use with water up to 85°C.
'VULCAN VEE4 Bellow & Boot'. Black coloured, compression moulded EPDM bellows and boot components. Shore hardness 70. The bellows has an in-radius size of 3.0mm and the boot has an in-radius size of 0.9mm. For use with water up to 85°C.
'CH EP 172 DM'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'SE-808PF'. Black coloured, compression moulded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7037K'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Pango2023'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 85°C.
'TRA-7073'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'CHEMILINE AI060 FB 1304'. Black coloured NR & SBR material manufactured by calendaring. Shore hardness 76 D. Tested in-radius size 1.0mm. Between June 2023 and June 2025, the material was for use with water up to 23°C. Between July 2025 and June 2028, the material is for use with water up to 60°C.
'S7107'. Red coloured, injection moulded silicone rubber seal. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'RBL-9200-20, RBL-9200-30, RBL-9200-40, RBL-9200-50, RBL-9200-60, RBL-9200-65 & RBL-9200-70'. Transparent, colourless injection moulded silicone rubber materials. Shore hardness between 20 & 70. Tested in-radii size between 0.75mm & 2.89mm. For use with water up to 85°C.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
Range of push fit stop valves with white plastic bodies. Maximum working pressure/temperature: 10bar @ 20°C and 4 bar @ 60°C.
Floor standing, single hole, single outlet (fixed) combination tap assemblies (brass body - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The product incorporates manual diverter to a shower outlet. The spout outlet incorporates an open outlet type spout. The product is supplied with a shower hose and handset. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The spout outlet incorporates a plastic aerator. Maximum working pressure - 8 Bar. Maximum operating temperature - 65 °C.
Range of wall mounted, two-hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve activated via infra-red sensor. Temperature is controlled independently via a thermostatic cartridge with a dome operating member which incorporates a manual override button. The spout outlets incorporate plastic aerators, and both inlets incorporate an approved single check valve cartridge (however, the complete assembly has not been fully tested to demonstrate that it provides adequate backflow protection) and stainless-steel strainers. Maximum working pressure 10.0 Bar. Maximum operating temperature 60.0°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Range of wall hung concealed WC flushing cisterns with a BS 1212-4 float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a push button assembly. Maximum working pressure - 10 Bar. Cold water use only.
Ceramic cartridge headwork with a plastic body, incorporating a silicone rubber ‘O’ ring. Intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of ceramic disc headworks incorporating brass bodies and NBR ‘O’-rings. For insertion into any specifically dimensioned bores. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar Maximum operating temperature 65.0°C
Range of ½ turn ceramic disc headworks, with brass bodies and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure: 5 Bar. Maximum operating temperature: 85°C.
Range of ceramic disc headworks with brass bodies and NBR ‘O’-rings. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Range of deck mounted, two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass), incorporating a quarter turn ceramic disc or a quarter turn compression washer headwork with various operating members (see model). The inlet of the quarter turn ceramic disc headwork incorporates an approved check valve cartridge, however the complete product has not been fully tested to demonstrate it provides backflow protection. The product incorporates a handheld pre-rinse spray with a self-closing trigger, either on a flexible hose within an overhead spring or as a fixed length flexible hose on a swivel arm (see model). Models are available with an additional swivel spout outlet, which incorporates a plastic aerator (see model). The swivel spouts have their own flow control in addition to the main headwork, this is also a quarter turn compression washer headwork with various operating members (see model) Maximum working pressure 6 Bar. Maximum operating temperature 65 °C
Range of single hole, single outlet fixed combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever (Elysian models) or dome type (Milani models) operating member. The spout outlet incorporates a plastic flow straightener (Elysian models) or a plastic aerator (Milani models). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of floor mounted single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with a single lever type operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, swivel, combination tap assemblies in various finishes. The models incorporate a ceramic cartridge headwork and a single lever operating member. The spout outlets incorporate a plastic flow straightener. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Wall mounted two-hole, single outlet (fixed) combination tap assemblies with brass bodies (chromium plated), incorporating a ceramic cartridge headworks and single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure: 5 bar. Maximum operating temperature: 60°C
Two hole, single outlet swivel combination tap assembly (chrome plated brass), incorporating non-rising spindle headworks with dome operating members. The spout outlet incorporates a plastic flow straightener. The product is supplied with metal backnuts. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of two hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating quarter turn ceramic disc headworks with either single lever, dome type or wheel operating members. The spout outlet incorporates a plastic aerator and the products are supplied with metal backnuts. Maximum working pressure; 10 Bar Maximum operating temperature 60°C
Range of two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass). Incorporating quarter turn ceramic disc headworks and single lever operating members. The spout outlet incorporates a plastic aerator. The products are also supplied with metal backnuts. Maximum working pressure 8.62 Bar Maximum operating temperature 60.0°C
Range of wall mounted, two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator, and the products are supplied with metal backnuts. Maximum working pressure 8.62 Bar Maximum operating temperature 60.0°C
Range of wall mounted or floor standing spout outlets (fixed or swivel - see model in various finishes). All models incorporate a plastic flow straightener, except for the 93-Floor Mounted Bath Filler which has a plastic aerator.
Non-metallic materials and components comply with BS6920 at 60°C
Page 110 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
