Range of spherical valves incorporating nickel plated brass bodies, chrome plated brass balls & Tee type operating member. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
ISIS range of single lever and T type operated spherical valves with DZR brass body and ball (chrome plated), and PTFE seals. Maximum working pressure 40.0 bar (¼”, 3/8”, ½”, ¾”, 1”, 1 ¼”, 1 ½”, & 2” models) Maximum working pressure 10.0 bar (2 ½”, 3” & 4” models) Maximum operating temperature 100°C
Range of spherical valves with brass bodies (brushed chrome plated), (red coloured) lever operating members and chrome plated brass ball. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies and EPDM coated ductile iron wedges. The valves are operated via a non-rising spindle with a hand wheel operating member or key and bar operating members (see model). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gate valves with blue epoxy coated ductile iron bodies, incorporating an NBR wedge and non-rising spindle with hand wheel operating member. Maximum working pressure 16.0 bar. Cold water use only.
Range of regulating valves with blue epoxy coated ductile iron bodies incorporating EPDM gaskets and hand wheel operating member. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of undercounter and passthrough commerical dishwashers with flow controlled by a solenoid valve and discharged via a type AB air gap (verified by test - suitable for backflow protection against fluid category 5). The inlet hose incorporates a stainless steel strainer. Maximum working pressure 4.0 bar. Maximum operating temperature 55°C.
Range of water conditioners with brass and stainless steel bodies, PTFE seals and sacrificial zinc anode. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.use only.
'M90 POM Particle'. White coloured (opaque), injection moulded POM material. For use with water up to 65°C.
'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Iron Red'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Ice Grey'. Factory applied, two-component, white coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tianbao SS Epoxy Coating'. Factory applied, two-component white coloured epoxy coating. Mix component 1 and component 2 in a mass ratio of 6:1 and apply as per manufacturer's operation in instructions 'Tianbao SS', 'version 1.0' issued on '06/02/2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Vinoleo ME'. Amber coloured lubricant to be applied as per manufacturer's instructions '163771', dated April 2016. For use with water up to 60°C.
'RADILON® A RV300RKC 306 BK' (black coloured). In December 2022, 'RADILON A RV300RKC 106 NT' (natural, appears off-white) was added to the approval. Injection moulded PA66-GF30 materials. For use with water up to 85°C.
‘Ultramid® A3EG10 FC Aqua Black 23285’. Black coloured, injection moulded PA66 material. For use with water up to 85°C.
Page 103 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
