'Kubota Powder TK1413F (SPD)'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's TDS 'RP23242', dated 'December 26, 2023'. Cure for 6 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kubota Powder TK1413F I'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's PDS '4384-23-403' dated '2023/11/16'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V-PET#1340QD-F GRAY'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions '2211447-2' dated '2023/11/16'. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'Epigard Solvent Free Epoxy Finish'. Factory applied, two-component, red coloured epoxy coating. Mix base & accelerator in a volume ratio of 3:1 and apply as per user instructions dated '20th Dec 2024'. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing and mixing conditions that appear on the approval. If the cure/mix conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VALVFIT 001 (blue) & VALVHIT 002 (red) Epoxy Powder Coatings'. Factory applied, blue or red coloured epoxy coatings. Apply as per manufacturer's TDS 'VALVFIT-2412001' dated '12.17.2024'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 860'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/05/2023'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP015-UTB'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions reference 'PR-CA-00-024' dated 15-02-19. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 864'. Factory applied, cream coloured, two-part Polyurethane coating. Mix parts A and B in a 66:34 volume ratio and apply as per manufacturer's TDS dated '26/11/2024'. Cure for 50 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SikaTop® 550 Seal’. Site applied, white coloured, two component Acrylic, Cementitious waterproofing coating. Mix 1kg of part A (powder) with 333g of part B (liquid) and apply as per manufacturer’s method statement ‘10/2024’. Cure for 28 days@23°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NATCEM 35'. Site applied, grey coloured natural cement mortar. Mix cement mortar with water in the ratio of 25kg:3.6 litres and apply as per manufacturer's IFU 'issue 4', dated '21 February 2023'. Cure/set for 4 hours@0°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Supranite 2400'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'AFM 34/2'. Beige coloured, calendered fibre gasket material. For use with water up to 85°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio
'Revolve N-461 Natural'. White coloured polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'MasterCrete ANC 932'. Site applied, grey coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1' dated '09.12.2024'. Cure for 48 hours@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterCrete ANC 920'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions 'Version 1', dated '09.12.2024' Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘MasterCrete ANC 915’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Version 1', dated '09.12.2024'. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'VULKODURIT 1250 KTW'. Dark grey/brown coloured, Ebonite rubber material made by extrusion and calendaring. Shore hardness 72D. Tested in-radius size 2.0mm. For use with water up to 40°C.
'E8124'. Black coloured, injection moulded EPDM seal. Shore hardness 80. Tested in-radius size 1.5mm. For use with water up to 85°C.
‘0548’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'CERULEAN EP 14 (KIEP14)'. Black coloured, compression moulded EPDM material. Shore hardness 72. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM50P - ELAST45901, EPDM60P - ELAST46901, EPDM70P - ELAST47901 & EPDM80P - ELAST48901’. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.3mm. For use with water up to 85°C.
‘Permabond A011 Red, A025 Orange, A113 Blue, A115 Orange, A118 Green, A130 Blue, A131 White, A134 Green, A136 Red, A140 Green, A1042 Blue, A1044 White, A1058 Off White, F200 Brown, F201 Brown, F202 Brown, A1084 Yellow & F201HV (translucent)’. Anaerobic adhesives to be applied and cured in strict accordance with the manufacturer's instructions. For use with water up to 85°C.
'NOVIPRO'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
'RIAMAXX HR XE4355 KTW-M schwarz & RIAMAXX HR XE4355 KTW-M sondergrau K 7-140‘. Black or grey coloured, injection moulded PK materials. For use with water up to 60°C.
'Butyl IIR 6038 diaphragm'. Black coloured, injection moulded Butyl diaphragm. Shore hardness 64 ShA. Tested in-radius size 1.25mm. For use with water up to 85°C.
Side and bottom entry BS1212 - 3 compact type float operated valve for WC flushing cisterns Maximum operating pressure 14 bar. Maximum operating temperature 23°C
Concealed WC dual flushing cistern with a bottom entry BS 1212 - 4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly for a 6 or 3 litre flush volume. Maximum working pressure 10.0 bar, cold water use only.
Range of concealed WC dual flushing cisterns with a vertical BS 1212-4(2016) float operated inlet valve providing a Type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two-push button assembly. The product also incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10 Bar, cold water use only.
Range of spring loaded, resilient trim check valve cartridges with plastic body. For insertion into fittings with specifically sized bores. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
GRPBP range of one piece, pre-insulated cold water storage cisterns and covers for domestic water storage, supplied with a wholesome water kit. The cisterns walls are available in grey, blue, green, white, red and anthracite grey (external) colours and the cistern base is straw coloured. For cold water use only. From November 2024 the water contact layer of the cistern base and walls is available in grey or straw colours. The outer layer of the cistern base is available in blue, green, white, red and anthracite grey colours.
Range of flow regulators, aerators and flow straighteners with plastic bodies. Maximum operating temperature 60°C.
Range of ceramic cartridge headworks with plastic bodies. For insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperatures 85°C (K26PMA-01NP model) and 65°C (K40P-01NPX model).
Range of ceramic cartridge headworks with plastic bodies for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Ceramic cartridge headwork with a plastic body, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 90°C.
Ceramic cartridge headwork with a plastic body and EPDM seals, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 16.0 Bar. Maximum operating temperature 80°C
Range of ½ turn ceramic disc headworks with plastic bodies (middle position off, quarter turn either way for hot or cold). For insertion into specifically dimensioned bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of quarter turn ceramic disc and non-rising spindle headworks. Maximum working pressure 10.0 Bar Maximum operating temperature 85 °C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies – various finishes). Incorporating a ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure 5.0 Bar Maximum operating temperature 60.0°C
Single hole, single outlet, fixed, combination tap assembly (chromium plated brass body), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of single hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes) incorporating a ceramic cartridge headworks with single lever operating members. Model 24.341.xxx is supplied with lever operated pop up waste (not verified by test). Maximum working pressure 10 Bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet, (fixed) combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. The product is supplied with 3/8” x 15mm reducers incorporating approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Product is to be used with an instantaneous water heater. Maximum working pressure: 10.0 bar Maximum operating temperature: 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Products incorporate an additional hose outlet and shut-off valve for use with an external domestic appliance. Maximum working pressure: 10.0 bar Maximum operating temperature: 60°C
Range of single-hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Maximum working pressure: 10.0 bar Maximum operating temperature: 60°C
Range of single hole, single outlet (swivel) pull out spray combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with a single lever operating member. The outlet incorporates a plastic aerator and a push button spray. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C.
Range of single hole, single outlet (swivel) combination tap assemblies with brass bodies (chromium plated), incorporating ceramic cartridge headworks and single lever operating member. The connection to flexible hose and spray outlets incorporates an approved single check valve cartridge (however, the whole product has not been fully tested to demonstrate that it provides adequate backflow protection) the outlets incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies with various finishes) incorporating a ceramic cartridge headwork with single lever operating member. The spout outlets incorporate an aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with dome type operating members. The spout outlet incorporates a plastic aerator. Maximum working pressure; 10 Bar Maximum operating temperature 65°C
Page 101 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
