Natural (appear white), black or grey, injection moulded, glass fibre reinforced nylon materials. Between September 2020 and February 2022 these grades are for use with water up to 85°C Grilamid LV-65H FWA black 9225. Grilamid LV-30H FWA grey 9497. Grilamid LV-30H FWA natural. Between September 2020 and February 2022 these grades are for use with water up to 23°C Grilamid LV-50H FWA natural. Grilamid LV-30H FWA black 9225. Grilamid LV-43H FWA black 9225. Grilamid LV-50H FWA black 9225. Grilamid LV-65H FWA natural. From March 2022, all grades are suitable for use with water up to 85°C.
'Sirester EC 0994/AT/V/15'. Pale green coloured orthothalic resin manufactured by hand lay-up. For use with water up to 23°C.
'100 US Gallon Dubai Polytank Panel'. Triple layered, rotationally moulded LLDPE tank panel comprising of a white coloured inner layer, black coloured middle layer and white coloured outer layer. For use with water up to 65°C.
'Radius Systems Socket Fittings and Saddle Fittings'. Black coloured, injection moulded PE fittings. For use with water up to 60°C.
'Revolve 6402U'. White coloured (translucent), polyethylene material manufactured by rotational moulding. For use with water up to 85°C.
'PE-BWG'. Transparent, extruded, single layer, polyethylene hose. In July 2023, 'PE-BWG Black', a black coloured (opaque), extruded, single layer, polyethylene hose was added to the approval. For use with water up to 85°C.
'Hostalen GM 5010 T3 Black'. Black coloured, extruded HDPE material. For use with water up to 23°C.
'Durafide® 1130A1T WF900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WF9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK900A'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'Durafide® 1130A1T WK9001'. Grey coloured, injection moulded PPS material. For use with water up to 85°C.
'DIC. PPS FZ-2140 BLACK'. 'DIC.PPS FZ-2140 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'400-GA05'. White (translucent), injection moulded polypropylene material. For use with water up to 85°C.
`Polyfill PPC GF2007 PD1 yellow`. Yellow coloured, injection moulded polypropylene material. For use with water up to 23°C.
'ISOFIL HK 40 5FH0 WT0580'. White coloured (opaque), injection moulded PP material. For use with water up to 85°C.
'ISOFIL H 40 C2 F NA1'. Grey coloured (opaque), injection moulded polypropylene material. For use with water up to 85°C.
'WS 9000'. Site applied, off-white coloured, fibre glass impregnated, polyurethane repair tape. Apply as per manufacturer's technical date sheet created '02/11/2010' and reviewed '30/01/2015'. Cure for 30 minutes@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ChemSet™ REO502 EF PLUS, Epcon™ C6 EF PLUS & Epcon™ G5 PRO’. Grey coloured, two-part epoxy resin anchor systems, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘JCP PURE EPOXY RESIN JF375E’. Two-part epoxy resin anchor systems, available in light pink or grey colours, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP6008'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 60. Tested in-radius size 0.8mm. For use with water up to 85°C.
Page 93 of 561
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
