Pressure relief valves with a brass body incorporating EPDM ‘O’ rings for 35890040 and EPDM diaphragm for 35900040, pre-set at 3.0 bar. Model 35890040 incorporates a manually operated lever type lifting gear Maximum working pressure 10 bar. Maximum operating temperature 90°C.
Range of spherical valves incorporating DZR brass (CORE 171 AC) or nickel-plated brass (CORE 800 ) bodies and chromium plated brass balls. For use with copper to BS EN 1057. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of in-line lever or screwdriver operated spherical valves with DZR brass bodies (nickel plated) and brass balls (chromium plated), EPDM ‘O’-rings and PTFE seats. The ball can incorporate a plastic flow regulator, or a stainless-steel strainer (within a plastic housing) inserted through the side port. Compression models are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperatures: Spherical valves only and those incorporating a stainless-steel strainer: 85°C. Spherical valves incorporating a plastic flow regulator: 60°C.
Range of spherical valve with a brass body (chrome plated) and chrome plated brass ball, incorporating EPDM o-rings. Compression connection to be used with copper pipe EN1057. Maximum working pressure 16 Bar. Maximum operating temperature 85°C.
Range of single lever ball valves with stainless steel bodies, ball, EPDM O-rings and PTFE gaskets. The press fit connection is to be used with stainless steel pipe manufactured to EN 10312. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of lever or butterfly lever operated spherical valves, incorporating a nickel plated brass body and stainless steel ball, PTFE seats and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of resilient seated gate valves with blue epoxy coated ductile iron bodies and bonnets and ductile iron wedges encapsulated in EPDM. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
Range of non-rising spindle gate valves with bronze, brass or DZR brass (165-XX Series only) bodies, incorporating hand wheel or key operated operating members. Maximum working pressure 16.0 Bar (131-XX Series) 25.0 bar Maximum working temperature: 85C
Non-metallic materials and components comply with BS6920 at 85°C
Range of non-rising spindle lock shield gate valves with DZR brass bodies. Maximum working pressure 16 bar. Maximum operating temperature: 65°C Maximum working pressure 10 bar. Maximum operating temperature: 82°C
Range of non-rising spindle gate valves with bronze bodies and wedges incorporating PTFE seals and a handwheel type operating member. Maximum working pressure and operating temperature: 16.0 bar @ 65°C. Maximum working pressure and operating temperature: 10.0 bar @ 82°C.
Range of gate valves with brass bodies and gates incorporating hand wheel type operating member. Max working pressure and operating temperatures: 16.0 bar at 65°C. Max working pressure and operating temperatures: 10.0 bar at 82°C.
Screw down stop valve, with brass body, HDPE seat and handwheel operating members. Maximum working pressure 10 bar. Cold water use only.
Range of brass stop valves with non-rising stems, having brass bodies, EPDM ‘O’ rings and PTFE gaskets and various operating members. To be used with copper pipe EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Tenant valve assemblies with a DZR brass body consisting of water meter manifold, servicing valve and a pressure reducing valve (adjustable between 1.0 and 6.0 bar). The inlet incorporates two approved check valve cartridges, verified by test (suitable for backflow protection against Fluid Category 3). Maximum working pressure 16.0 bar.
‘MagCat’ range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
'DURACON®M90-44 WK3068'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'KEPITAL F10-03H BBK & KEPITAL F10-03H BK'. Black coloured, injection moulded POM materials. For use with water up to 85°C. 'KEPITAL F10-52H'. Natural (appears white), injection moulded POM material. For use with water up to 40°C.
'PCBIT III HIGHBUILD'. Factory applied, black coloured bituminous coating. Apply as per manufacturer's instructions for use, reference 'PCC/ PC 820' dated 27.11.2023. Cure for 5 minutes@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hilox 961'. Brown coloured, dry pressed ceramic material. For use with water up to 85°C.
'JDFF epoxy powder coating’. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s instructions (Procedure #: Pc-01-3, Work Instruction #: JDFF WI-Pc-01-3-1, Revision #: 2, Issue #: 5, date: 10-01-2023). Cure for 2½ minutes at 232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Cleantech PW'. Factory applied, two-component, red coloured epoxy coating. Mix component A and component B in a volume ratio of 3:1 and apply as per manufacturer's product data sheet 'CCPL/TDS/R11/CRC/17-18/04/R6/spray'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured fusion bonded epoxy powder coating. Apply as per manufacturer's Product Information '704G_TDS', revised 'August 16,2022'. Post-cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the post-curing conditions that appear on the approval. If the post-cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions reference 'XA12312', dated 26/12/2022. Cure for 15 minutes@220°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'PPA571ES Black 700 & PPA571 Black 700'. Factory applied Polyolefin PE Coatings. Apply 'PPA571 Black 700' by fluidised bed according to manufacturer's data sheet '08/2022' and dip in the bed for 5-8 seconds. Apply 'PPA571ES Black 700' by electrostatic spray according to manufacturer's data sheet '08/2022'. Cure for 190-200°C for 20 mins. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL035P Interpon 100 Gloss Light Grey'. Factory applied, light grey coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'Interpon 100 -AL035P - Issue #01', revision date '20.07.2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'CY7000 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instruction manual 'YS-QNS-WZBC-2021W', dated 'May 20, 2021'. Cure for 15 minutes@180°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per Kluber Lubrication product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'68093X'. Factory applied, blue coloured epoxy powder coating. Apply per manufacturer's instructions 'V2.3' dated March 2018. Cure for 20 minutes@200°C For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kinlin Epoxy Power Coating (Green colour, EPX‐111A)'. Factory applied, green coloured epoxy powder coating. Apply as per manufacturer's instructions 'XL-R-019-G1' dated '2018-9-21'. Cure for 10 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Planigraph LG'. Grey coloured graphite material manufactured by expansion/compression moulding. For use with water up to 85°C.
'Planigraph LGRF'. Grey coloured, steel-reinforced, graphite material manufactured by calendaring. For use with water up to 85°C.
'KORASILON® Paste hochviskos' & 'KORASILON® Paste M-S 2-200'. White coloured (translucent) lubricants. Apply as per manufacturer's Product Data Sheet '30.01.2023'. For use with water up to 85°C.
'POLYWORK® H2G50DW NC' (appears off-white) & 'POLYWORK® H2G50DW BK' (black coloured). Injection moulded glass fibre reinforced PA66+PA6I/6T materials. For use with water up to 85°C.
'Vydyne A SG Natural WR'. Natural (appears white in colour), injection moulded PA 66 material. For use with water up to 85°C.
'Akoalit PB 4237 and Akoalit PB 4238 White'. Grey or white coloured, extruded PB materials. For use with water up to 85°C.
'Spectrum Polyester Felt Filter Media'. White coloured, extruded, polyester felt media. For use with water up to 38°C.
'Spectrum Polyethersulfone Pleated Filter Media'. White coloured, pleated polyethersulfone filter media/membrane, manufactured by casting. For use with water up to 85°C.
'LK PE-Xa pipe'. The pipes are either single layered or multi-layered (3 or 4 layers). The single layered, extruded pipes are natural (off-white coloured) PE-Xa. The multi-layered, extruded and IR cross-linked pipes have a natural (off-white coloured) PE-Xa inner layer, an adhesive layer, an oxygen barrier layer based on EVOH and then an optional 4th, adhesive layer. All are for use with water up to 85°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
'PPA-GF10-NC' (natural, appears yellow-green) & 'PPA-GF10-BK' (black coloured). Injection moulded PPA materials. For use with water up to 85°C.
'Flowtech & Atlas PP-R Pipe'. Green coloured, extruded PP-R pipes. For use with water up to 85°C.
'Polytech PPR Pipes'. Green coloured, extruded PPR pipes. For use with water up to 85°C.
'Vissen PP-R Pipe'. Green coloured (red, external stripe), extruded PP-R pipe. For use with water up to 85°C.
'AQUA PLUS PPR-CT Pipe'. Green coloured, extruded, single layered polypropylene pipe. For use with water up to 85°C.
'AQUA PLUS PPR-CT GF'. Extruded, triple layered polypropylene pipe consisting of a green coloured polypropylene inner layer, natural (appears grey in colour) glass fibre middle layer and green coloured polypropylene outer layer. For use with water up to 85°C.
'Spectrum Polypropylene Filter Media'. White coloured, extruded polypropylene felt filter media. For use with water up to 85°C.
'PTFE G453'. Black coloured, extruded PTFE material. For use with water up to 85°C.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 87 of 158
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
