Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitors with chromium plated copper bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 35°C
Electrolytic and magnetic scale inhibitors incorporating copper or nickel coated copper bodies. Compression models are to be used with copper pipe manufactured to BS EN1057. Maximum working pressure 10.0 bar. Cold water use only.
Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
'Kersic 1000'. Grey coloured, compression moulded silicon carbide ring. For use with water up to 85°C.
‘KUBOTA SEAL AC’. Factory applied, colourless acrylic resin coating. Apply as per manufacturer’s instructions ‘ref. no. 65700H-2.3’ dated 'Mar. 14.2017'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘V-PET#1600 Gray F’. Factory applied, dark grey coloured epoxy resin powder coating. Apply as per manufacturer’s instructions ‘ref.no. VP1600-PD-170412’, dated '12th April 2017'. Cure for 10 minutes@200°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'5013 High chlorinated polyethylene anticorrosive coating'. Factory applied, blue coloured polyethylene coating. Apply as per manufacturer's TDS/IFU number '001', dated '2022.11.30'. Cure for 24 hours@23°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC GRP Pipe'. Beige coloured (translucent), SRC GRP pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'SRC GRV Pipe'. Beige coloured (translucent), SRC GRV pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'SRC GRE Pipe'. Yellow coloured (opaque), SRC GRE pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'Extrabrite'. Light brown coloured GRE pipe manufactured by filament winding (at Extra Co Fibre Glass & Prefab Houses LLC – Sharjah, UAE and Extra Co Industries LLC – Ras Al Khaimah, UAE). For use with water up to 60°C.
'Extrabrite'. Light brown coloured GRE fittings manufactured by filament winding (at Extra Co Fibre Glass & Prefab Houses LLC – Sharjah, UAE) or hand lay-up (at Extra Co Industries LLC – Ras Al Khaimah, UAE). For use with water up to 60°C.
'SURU Lubricant'. Yellow coloured lubricant. Apply as per manufacturer's instructions dated '18th Feb 2015'. For use with water up to 60°C.
'EPLAMID 66 GFS 30 FW NC'. Natural (appears beige), injection moulded, glass fibre reinforced PA66 material. For use with water up to 85°C.
'EPLAMID 66 GFS 30 FW BK'. Black coloured, injection moulded, glass reinforced PA66 material. For use with water up to 85°C.
‘RADISTRONG® AROMA RV400RKC2 106 NT, RV500RKC2 106 NT & RV600RKC2 106 NT’. ‘RADISTRONG® AROMA RV400RKC2 306 BK, RV500RKC2 306 BK & RV600RKC2 306 BK’. ‘RADISTRONG® AROMA RV300RKC2 106 NT’ & ‘RADISTRONG® AROMA RV300RKC2 306 BK’ were added to the approval in February 2024. Natural (indicated by NT - appear cream in colour) and black coloured (indicated by BK), injection moulded, glass fibre filled (between 30% & 60%), PA66 materials. For use with water up to 85°C.
'EUREXPOL PI6808C'. Yellow coloured, isophthalic unsaturated polyester resin material made by mixing and pouring into a mould. For use with water up to 23°C.
'SLA Barrier Pipe' (formerly known as ‘Egeplast SLA Pipe’). Extruded, triple layered pipe consisting of an black coloured PE 100 inner layer, aluminium middle layer and blue coloured (with brown coloured longitudinal stripe) PE 100 outer later. For use with water up to 23°C.
‘Palaplast Hydropal W PE80 & PE100 pipes’. Extruded, PE80 & PE100 pipes, both available in either blue colour or black colour (with blue stripe). All pipes are for use with water up to 23°C.
‘Polypipe Black PE100 & Blue PE100 Pipes’. Black or blue coloured, extruded PE100 pipes. For use with water up to 23°C.
'Aquaflex PE-80'. Blue coloured, extruded HDPE pipe. For use with water up to 23°C.
'PPE-2211 GF30 SAWyy-Gxxxx' (where yy-Gxxxx indicates and is replaced with a combination of numbers and letters). Off-white coloured, injection moulded PPE material. For use with water up to 85°C.
'Q-Therm'. Green coloured, extruded PP-R 80 pipes. For use with water up to 85°C.
'TFM1700'. White coloured, injection moulded PTFE ring. For use with water up to 85°C.
'Titan A202'. Site applied, pale yellow coloured hydrophilic polyurethane foam. Apply as per manufacturer's Tech Sheet '03', dated '10.01.2023' and spray treated surface with water. Cure for 6 hours at an ambient temperature (19-21°C). For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CHEMILINE AF 023 FB 170'. Black coloured CR & SBR rubber material which has been calendared and then cured in an autoclave. Shore hardness 55. Tested in-radius size 1.05mm. For use with water up to 23°C.
‘Sunaflex T 9635’. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. Between March 2023 and August 2023, the material was for use with water up to 23°C. Between September 2023 and March 2028, the material is for use with water up to 80°C.
'A-KT 80-00'. Black coloured, extruded EPDM rubber material. Shore hardness 80. Tested in-radius size 1.1mm. Between April 2023 and May 2025, the material was for use with water up to 23°C. Between June 2025 and April 2028, the material is for use with 85°C.
'A-KT 90-00'. Black coloured, extruded and rotocured EPDM rubber material. Shore hardness 90. Tested in-radius size 1.0mm. Between April 2023 and October 2024, the material is for use with water up to 23°C. From November 2024, the material is for use with water up to 85°C.
'EPNER-4665'. Black coloured, compression moulded EPDM material. Shore hardness 50. Tested in-radius size 1.0mm. For use with water up to 50°C.
‘CRIEP50 & CRIEP80’. Black coloured, compression moulded EPDM rubber materials. Shore hardness 50 & 80 respectively. Tested in-radius size 1.0mm. For use with water up to 70°C.
'EIW-54'. Black coloured, injection moulded EPDM material. Shore hardness 51 ShA. Tested in-radius size 0.5mm. For use with water up to 50°C.
‘N5118F, N5518F, N6118F, N6518F, N7118F, N7008F, N7518F, N8118F, N8518F & N9118F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
'NP7055K'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘KSIL70’. Natural (off-white coloured), silicone rubber gaskets manufactured by pulltrusion. Shore hardness 70. Tested in-radii sizes between 0.55mm & 0.85mm. For use with water up to 85°C.
‘2061 VMQ 60’, red coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 60. ‘2172 VMQ 70’, blue coloured, injection moulded silicone rubber 'O' rings, washers and lip seals with a shore hardness of 70. O-rings have a tested in-radius of 2.0mm Washers have a tested in-radius of 2.5mm. Lip seals have a tested in-radius of 0.45mm For use with water up to 85°C.
‘SIL4008F, SIL4008F (N), SIL4008F (H), SIL4008F (R) & SIL4008F (BK). SIL4508F. SIL5008F, SIL5008F (H), SIL5008F (R) SIL5008F (BK), SIL5008F (B). SIL5508F. SIL6008F, SIL6008F (N), SIL6008F (H), SIL6008F (R), SIL6008F (BK). SIL6508F. S7008F, S7008F (N), S7008F (H), S7008F (R), S7008F (BK), SIL7118F, SIL7018F. SIL7508F. SIL8008F, SIL8008F (N), SIL8008F (H), SIL8008F (R), SIL8008F (BK)’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
'EMS Force 5543'. 'EMS Force 5543-P' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '07/03/2016'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Zilan DW-HT Rubber Membrane'. Black coloured, compression moulded butyl rubber membrane (in the form of a sheet of rubber). Shore hardness 50 ShA. Tested in-radius size 1.0mm. For use with water up to 85°C.
'IPF-PVC-U-H2O Pipe'. Grey coloured, extruded u-PVC pipe. For use with water up to 60°C.
3-in1 single hole, single outlet (swivel) combination tap assembly (chromium plated or brushed stainless steel PVD brass). The cold//hot/mixed water circuit incorporates a ceramic cartridge headwork with a single lever operating member. The near boiling water circuit incorporates a quarter turn ceramic disc headwork with a single lever operating member. The tap is supplied with a stainless steel braided PEX lined flexible hose assembly, brass adaptor incorporating a plastic flow regulator, NBR washer and plastic adaptor to connect the tap to the near boiling water unit (not supplied) and a PTFE or silicone (from September 2024) flexible pipe to deliver near boiling water back to the tap. The spout outlet incorporates a plastic aerator, which includes a central stainless steel tube insert throughout the near boiling water outlet of the aerator. Maximum working pressure 10.0 bar. Maximum operating temperatures: 65°C (cold/hot/mixed water circuit). 99°C (near boiling water circuit after boiler unit, cold supply only prior to boiler unit).
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated by via an infra-red sensor and a manual lever to control the outlet temperature. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 Bar. Temperature:60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, single-hole, single outlet (fixed) electronically controlled combination tap assemblies (chrome plated brass bodies). Flow is controlled via a solenoid, activated via an infra-red sensor. The outlets incorporate plastic aerators. Maximum working pressure 8.0 bar Maximum operating temperature 70°C
Non-metallic materials and components comply with BS6920 at 70°C
Range of wall mounted, electronically operated, combination tap assemblies (stainless steel body, various finishes - see model), comprising of a Premix control unit and a spout. The flow is controlled by a solenoid valve, (Premix control unit), which is actuated via an infrared sensor. The central section of the valve incorporates a plastic strainer. Both inlets of the Premix control unit incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Non-metallic materials and components comply with BS6920 at 60°C
Range of wall mounted, electronically operated combination tap assembly (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlets incorporate a plastic aerator. The solenoid valve inlet incorporates a plastic and stainless steel filter. The products are supplied with a triple layered connecting hose (PVC inner and outer layer and nylon braided middle layer). Maximum working pressure 8.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Electronically operated combination tap assembly, (chrome plated brass body). The flow is controlled by a solenoid valve which is actuated via an infrared sensor on the spout. The spout outlet incorporates a plastic aerator. The product is supplied with a stainless steel braided (EPDM or PEX lined) flexible connecting hose. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 60°C
M100 & M100-B30 ranges of hot press moulded GRP sectional, pre-insulated, cold water storage cisterns. The cisterns are sealed with butyl rubber and are supplied with a float operated valve (gunmetal or DZR brass body depending on size). The rooves are fitted with one or more sealed manhole access points, which can also be fitted at low level if required. Larger cisterns are fitted with stainless steel ties, GRP roof struts & GRP ladders. The M100-B30 models are supplied with a screened tank overflow, a screened tank breather, two-way expansion pipe tee piece, tank lid adaptor and tank connections. Models can also be supplied with access doors. Maximum working pressure of supplied inlet valve: Gunmetal body inlet valves 5.0 bar, DZR brass body inlet valves 10.0 bar. Cold water use only.
Range of basin bidet mixers with brass bodies, incorporating a ceramic cartridge headwork, and a single lever operating member. The spout incorporates a plastic aerator within a swivel nozzle. This product is supplied with a lever type pop up waste (not tested). Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 60°C
Quarter turn ceramic disc headwork with brass body, NBR and silicone rubber ‘O’ rings, for insertion into specifically dimensioned tap assemblies. Maximum working pressure 10.0 bar. Maximum operating temperature 90°C
Non-metallic materials and components comply with BS6920 at 90°C
Page 84 of 236
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
