Dual flush WC outlet valve operated via a push button assembly for either full or reduced flush. The product incorporates an internal overflow.

Section:

1305 Valves

Section Subtitle:

Flushing valve(s) for WC Except where specified, flushing valves within this section have only completed a limited number of the performance and endurance tests as stated in the "Regulators Specification for WC suites installed after 1st January 2001". The flush volume of valves within this section have not been verified by test. When installed in combination with a WC cistern and pan, further performance tests will be required.

WRAS Approval Number:

260302702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Open outlet, cold water use only

Size:

2” BSP (M)

Marking:

Roca logo on operating member. Roca logo and model code on body.

Installation Requirements:

R001 R556 R571 R572

Expiry date:

31/03/2031

Model:

D8E

Approval Holder:

Roca Sanitario SA

Company Name

Roca Sanitario SA

Address

Av. Diagonal 513, Barcelona, Spain

View All Listings by this Company

Manufacturer:

Xiamen R&T Plumbing Technology Co.,Ltd

Company Name

Xiamen R&T Plumbing Technology Co.,Ltd

Address

No.18, Houxiang Road Haicang District Xiamen

Postcode

361022

Country

China

Phone

86-0592-3959422

View All Listings by this Company

Electric vented mains water heater with metal housing and silicon rubber gaskets. The inlet incorporates a combined EPDM washer and stainless-steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 98°C. Open outlet use only.

Section:

1365 Heaters

Section Subtitle:

Electric instantaneous, open outlet, mains fed.

WRAS Approval Number:

260302701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Inlet: ¼” LLDPE pipe. Outlet: ⅜” BSP (M).

Marking:

Abode on front of body. Model name and other technical information on adhesive label on rear of body.

Installation Requirements:

R001 R008

Expiry date:

31/03/2031

Model:

PROBOIL.3X

Approval Holder:

Norcros Group (Holdings) Limited T/A Abode

Company Name

Norcros Group (Holdings) Limited T/A Abode

Address

Unit L Zenith Park Whailey Road Barnsley

Postcode

S75 1HT

Country

United Kingdom

Phone

01226 283434

General Email

info@abode.eu

View All Listings by this Company

Range of ultrasonic water meters incorporating a brass or plastic (-C suffix models only) body. The inlet incorporates a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

KDM Series: ¾" - 2½ BSP (M) (DN15 to DN50). VDE Series: ¾" - 1" BSP (M) (DN15 to DN20).

Marking:

CEM Water Meters on cap. CEM Water Meters, pressure, serial code, model code and other technical info on dial body. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

KDM Series, Multijet, Dry Type KDM1, KDM2, KDM3, KDM4, KDM5, KDM6, KDM7, KDM8, KDM9, KDM10, KDM11 VDE Series Volumetric, Dry Type, Brass Body VD1E, VD2E, VD3E, VD4E, VD5E, VD7E Volumetric, Dry Type, Composite Body VD1E-C, VD2E-C, VD3E-C, VD4E-C, VD5E-C, VD7E-C

Approval Holder:

Yavuz Metal Sanayi Ve Ticaret A.Ş.

Company Name

Yavuz Metal Sanayi Ve Ticaret A.Ş.

Address

Organize Sanayi Bolgesi 2 Cadde No 4 Arsin Turkey

View All Listings by this Company

Range of ultrasonic water meters with brass (DN15-50) or plastic (DN15-20 only) bodies, EPDM ‘O’-rings and a plastic strainer. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1505 Water Meters

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN15: ¾" BSP(M), DN20:1" BSP(M), DN25: 1¼" BSP(M), DN32: 1½" BSP(M), DN40: 2" BSP(M), DN50: 2½" BSP(M).

Marking:

Manufacurers logo, AFlow LXC and product info on face. Flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

AFlow LXC

Approval Holder:

Hunan Winmeter Energy Technology Co.,Ltd.

Company Name

Hunan Winmeter Energy Technology Co.,Ltd.

Address

468# West Tongzipo Road, Hi-Tech Industrial Development Zone, Changsha, Hunan

Country

China

View All Listings by this Company

Range of flexible joints incorporating an EPDM (inner & outer) joint with a steel reinforcing ring and two carbon steel flanges. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN32 DN40 DN50 DN65 DN80 DN100 DN125 DN150

Marking:

CORE (Smith Brothers Stores Ltd brand) model, DN, PN, date of manufacture, WRAS metal plate riveted on to flange approved & Made in China on body.

Installation Requirements:

R001

Expiry date:

31/10/2026

Model:

FB16032W FB16040W FB16050W FB16065W FB16080W FB16100W FB16125W FB16150W

Product Images

Approval Holder:

Smith Brothers Stores Limited

Company Name

Smith Brothers Stores Limited

Address

Unit V2 Winchester Avenue, Blaby, Leicester

Postcode

LE8 4GZ

Phone

0116 222 7330

General Email

kel.phillips@sbs.co.uk

View All Listings by this Company

Range of cast iron (blue epoxy coated) (G versions only) or stainless steel (all other versions - F, N, R, T) vertical multistage pumps with stainless steel impellers, shaft and outer sleeve. Maximum working pressures: 16 bar, 25 bar and 40 bar. Oval flanges - Body type ‘T’ (1SV-3SV, 5SV, 10SV, 15SV-22SV) - 16 bar. Round flanges - Body type ‘R’ (1SV-3SV, 5SV, 10SV, 15SV-22SV) - 25 bar. Round flanges - Body type ‘F’ (1SV-3SV) - 25 bar. Round flanges - Body type ‘N’ (10SV) - 25 bar. Round flanges - Body type ‘N’ (66SV-92SV) - 16 bar. Round flanges - Body type ‘G’ (33SV, 46SV) - 40 bar. Round flanges - Body type ‘G’ (33SV, 46SV, 66SV-92SV, 125SV) - 16 bar. Round flanges - Body type ‘G’ (125SV) - 25 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

260302709

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Flanged inlet and outlet: (T versions have 2 bolt oval flanges). (F, G, N, R versions have round flanges). 1SV-3SV: DN25. 5SV: DN32. 10SV: DN40. 15-22SV: DN50. 33SV: DN65. 46SV: DN80. 66SV-92SV: DN100. 125SV: DN125.

Marking:

Lowara logo, Xylem, pressure and technical data on data plate on body. Lowara and WRAS on adhesive label on body DN80 46SV_10G_055 Lowara logo, Xylem, pressure and technical data on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

31/03/2031

Model:

1SV, 3SV, 5SV, 10SV, 15SV, 22SV, 33SV, 46SV, 66SV, 92SV & 125SV series pumps. Example code: 10SV_05F_022_ _T/D Where: • 10 = flow rate in m³/h (1, 3, 5, 10, 15, 22, 33, 46, 66, 92, 125). • SV = series name. • _ = Motor operation. blank = standard version, H = equipped with Hydrovar, E = e-SM (1SV-22SV models only) or a single letter denoting the type of the variable speed drive model used. • 05 = 2 digits for number of impellers [05 = 5 impellers], can also be represented as: X/1A or X/2A, where X = number of impellers: 1-13, /1 or /2 = 1 or 2 impellers with outer diameter reduced. A = reduction type. • F = body type: F, T, R, G or N. 1SV-25SV models F - AISI 304, round flanges, T - AISI 304, oval flanges, R - AISI 304, discharge port above suction, round flanges, N - AISI 316, round flanges. 33-125SV models G - AISI 304/Cast Iron, round flanges. N - AISI 316, round flanges, • _ = blank (null) to denote standard version. • 022 = Rated motor power - 3 digits (kW x 10). • _ = blank (null) to denote 2-pole, 4 = 4 pole. • _ = blank (null) to denote 50Hz, 6 = 60Hz, 0 = e-SM (1SV-22SV models only). • T = Three-phase or M to denote single-phase or Null = standard version. • /D = relates to supply voltage and can also be blank, /2, /4 or /4/2.

Approval Holder:

Xylem Service Italia S.r.l

Company Name

Xylem Service Italia S.r.l

Address

Via Vittorio Lombardi 14, 36075 Montecchio Maggiore-Alte Ceccato VI, Vicenza

Country

Italy

Phone

0039 0444 707111

View All Listings by this Company

Range of electronic booster pumps with variable speed, incorporating stainless-steel bodies, impellers and shaft, EPDM gaskets and seals and an expansion vessel on the outlet. The pumps incorporate a drain port. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

260304701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

The discharge from the drain port must be via a type `AA`, `AB` or `AD` airgap, or in accordance with EN1717.

Size:

PBI-L2 prefix models: 1” BSP (F) x 1” BSP (F), PBI-L4 prefix models: 1¼” BSP (F) x 1” BSP (F), PBI-L8 prefix models: 1½” BSP (F) x 1¼” BSP (F).

Marking:

Wilo, model no., date of manufacture (YYWW) and other technical information on data label on body. Wilo on control box.

Installation Requirements:

R001 R415

Expiry date:

31/03/2031

Model:

PBI-L series pumps: PBI-L203MA/P, PBI-L204MA/P, PBI-L205MA/P, PBI-L402MA/P, PBI-L403MA/P, PBI-L404MA/P, PBI-L405MA/P, PBI-L802MA/P, PBI-L803MA/P, PBI-L203EA/P, PBI-L204EA/P, PBI-L205EA/P, PBI-L402EA/P, PBI-L403EA/P, PBI-L404EA/P, PBI-L405EA/P, PBI-L802EA/P, PBI-L803EA/P, PBI-L203MA/P/S, PBI-L204MA/P/S, PBI-L205MA/P/S, PBI-L402MA/P/S, PBI-L403MA/P/S, PBI-L404MA/P/S, PBI-L405MA/P/S, PBI-L802MA/P/S, PBI-L803MA/P/S, PBI-L203EA/P/S, PBI-L204EA/P/S, PBI-L205EA/P/S, PBI-L402EA/P/S, PBI-L403EA/P/S, PBI-L404EA/P/S, PBI-L405EA/P/S, PBI-L802EA/P/S, PBI-L803EA/P/S. Where: PBI-L = series name (Electronic boosting pump variable speed pump (Inverter Pump)) 2, 4 or 8 = Rated flow capacity in m³/h. 2, 3, 4 or 5 = Number of Impellers. M or E = Power. M: 60Hz 220V/230V 1phase, E: 50Hz 220V/230V 1phase. [blank] or A = Mode. [blank]: Non-automatic models, A: Models with pressure sensor and inverter that are responsible for automatic mode, allowing the pump to operate at the corresponding RPM to maintain the set operating pressure. P = Product Category. P: Complete product. [blank] or S = Accessories. [blank]: No accessories, S: Sun cover.

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Manufacturer:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Range of circulating pumps, with plastic or stainless steel (cast EN 1.4308) bodies and a plastic impeller. Maximum working pressures: Stainless steel bodied pumps 10.0 bar, Plastic bodied pumps 3.0 bar. Maximum operating temperature 95°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

260307701

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

R008 does not apply to the stainless-steel body models.

Size:

Composite (plastic body) (15 models): 1” BSP (M). Stainless steel body (25 models): 1½” BSP (M).

Marking:

Grundfos and Grundfos logo, type, model, production no. and other technical info on adhesive label on end of motor housing. Flow arrow on body.

Installation Requirements:

R001 R008

Expiry date:

31/03/2031

Model:

Composite (plastic body): UPM2 15-** CIL2. Stainless steel body: UPM2 25-** N130, UPM2 25-** N180, UPML 25-** N180, UPMM 25-** N180, UPMXL 25-** N180. 130 or 180 (where applicable) = port to port length in mm. ** stands for the lifting height of the pump in dm, that can be various 2 or 3 digit numbers

Approval Holder:

Grundfos Holding A/S

Company Name

Grundfos Holding A/S

Address

Poul Due Jensens Vej 7 Bjerringbro

Postcode

DK-8850

Country

Denmark

Phone

+36302482216

General Email

oszilagyi@grundfos.com

View All Listings by this Company

Overhead shower outlet with chrome plated plastic body incorporating a filter and a flow regulator. The product incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Open outlet use only. Maximum operating temperature 60°C..

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

260304010

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

½” BSP (F)

Marking:

T-Safe on face plate.

Installation Requirements:

R001

Expiry date:

31/03/2031

Model:

02-803500 - Aegis Overhead Shower Filter. Models added March 2026: 02-803510 - Aegis Overhead Shower Filter, 02-803520 - Aegis Overhead Shower Filter.

Approval Holder:

T-safe A/S

Company Name

T-safe A/S

Address

Gydevang 1, Alleroed

Postcode

3450

Country

Denmark

Phone

+45 61610518

General Email

moj@t-safe.com

View All Listings by this Company

Section:

1650 Shower Outlets

Description:

A Range of Shower head(s) and/or shower handset(s).

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R040

Expiry date:

31/03/2031

Product Images

Approval Holder:

Kohler Mira Ltd.

Company Name

Kohler Mira Ltd.

Address

Cromwell Road Cheltenham Gloucestershire

Postcode

GL52 5EP

Country

United Kingdom

Phone

07425 645619

General Email

jon.barfield@mirashowers.com

View All Listings by this Company