Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
Range of modular silver and copper disinfection ion generators with a stainless-steel bodies Maximum working pressure 9.0 bar. Cold water use only.
'BPL High Build QD Bitu Black'. Factory applied, black coloured bituminous coating. Apply as per manufacturer’s data sheet ‘427-rev03’ dated 'Feb' 2024'. Cure: flash off for 15 minutes at ambient temperature of 30°C, followed by stoving at 55°C for 10 minutes and then 7 days maturation at ambient temperature of 30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘BFSC Foug SDN’. Factory applied, grey coloured, blast furnace slag cement intended to line pipes. Mix sand and cement in a mass ratio of 1.5:1, then add water in a water/cement mass ratio of 0.36:1 and apply as manufacturer's instructions. Cure for 48 hours@23°C, 70% relative humidity. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ARC SD4i(E)'. Factory applied, grey and blue coloured, two-part epoxy coatings. Mix parts A and B in a weight ratio of 2.5:1 and apply as per manufacturer's Application Instructions 'EN-085034EU', dated '01/2025'. Cure for 72 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ARC 858(E)'. Factory applied, dark grey coloured, two-part epoxy coating. Mix parts A and B in a weight ratio of 4:1 and apply as per manufacturer's Application Instructions 'EN-085013EU', dated '08/2024'. Cure for 54 hours@20°C (±2°C). For use with water up to 55°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE® 851 Blanc'. Factory applied, white coloured, two-component polyurethane coating. Mix parts A & B in 50:50 volume ratio and apply as per manufacturer's TDS dated 10/07/2024. Cure for 6 days@40°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'CLEAN TECH PW (BG)'. Factory applied, two-component, blue coloured epoxy coating. Mix parts A and B in a volume ratio of 3:1 and apply as per manufacturer's TDS 'CCPL/TDS/R11/CRC/22-23/04/R13/BG/R1', dated '15.09.2022'. Cure for 7 days@30°C. Between August 2024 and January 2025, the coating is approved for use with water up to 23°C. Between February 2025 and August 2029, the coating is approved for use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Advashield PW'. Factory applied, grey coloured epoxy coating. Apply as per manufacturer's TDS issued 1st September 2024. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Novus N34 & SF3300'. NBR/fibre gaskets which are white coloured on one side and dark cream coloured on the other, maufactured by calendaring. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at reduced surface area to volume ratio.
'AFM 34'. Beige coloured, calendered fibre gasket material. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio
'UNISILKON L 641'. White coloured (opaque) lubricant grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'Relon A500 Nero 4095 GF30 K'. Black coloured, injection moulded, glass filled PA66 material. For use with water up to 80°C.
'TP13444 Black'. Black coloured, rotomoulded, polyethylene material. For use with water up to 85°C.
FORTRON® natural (appears cream) or black coloured, injection moulded PPS materials. For use with water up to 85°C. Grades manufactured in Celanese Florence, USA: FORTRON® 1140L4 SF3001 NATURAL FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140L4 BLACK SD3002). FORTRON® 1140L6 SD3002 BLACK DW (formerly known as FORTRON® 1140L6 BLACK SD3002). FORTRON® 1140L6 SF3001 NATURAL FORTRON® 4184L6 SF3001 NATURAL FORTRON® 4184L6 SD3002 BLACK DW (formerly known as FORTRON® 4184L6 BLACK SD3002). Grades manufactured in Celanese Nanjing: FORTRON® 1140L4 SF3001 NATURAL DW (formerly known as FORTRON® 1140 L4 SF3001 natur CN). FORTRON® 1140L4 SD3002 BLACK DW (formerly known as FORTRON® 1140 L4 SD 3002 black).
'BC245MO' & 'Bn BC245MO-90'. Natural (off-white), injection moulded polypropylene material. For use with water up to 85°C.
'1024 Titan Bladder'. Clear (translucent), extruded TPU bladder. Shore hardness 87. Tested in-radius size 0.48mm. For use with water up to 80°C.
'EP703904 'O' rings'. Black coloured, injection moulded EPDM 'O' rings. Shore hardness 70. Tested in-radius size between 0.5mm & 3.0mm. 'EP703904 Gasket Seal Rings’ were added to the approval in June 2024. Black coloured, injection moulded EPDM gasket seal rings. Shore hardness 70. Tested in-radius size between 0.75mm & 2.0mm. For use with water up to 85°C.
'Loctite 403'. Clear, liquid cyanoacrylate adhesive. Apply as per manufacturer's technical data sheet reference ‘2.6’, dated August 2012. Cure for 72 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘JET Pipe Sealing Cord’. White coloured nylon cord coated with a silicone paste, intended for use as a thread sealant. The cord is to be applied and tightened in accordance with Data Sheet ‘P02415', updated 11/07/24 and this material is only approved for these conditions. For use with water up to 85°C.
'Datkafix DF-43'. Blue coloured pipe sealant. Apply as per manufacturer's TDS '01/02/2024 v1.1'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TruTite™ 313 Thread Lock'. Blue coloured pipe sealant. Apply as per manufacturer's TDS version '1.0 26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'CORE®'. Blue coloured pipe sealant. Apply as per manufacturer's instructions version '1', issue date '26/07/24'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The main body incorporates a plastic flow regulator and stainless steel strainer prior to the solenoid. The inlets to the main body of the GS10, CM10 & GH10 model variants incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. These models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a TPE gasket. The models are supplied with or without a pop-up waste. The GS20 & GM20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, single hole, single outlet (fixed) electronically controlled tap assemblies (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The inlets to the main body of the M10, GC10, MX10, A10 & L10 model variants incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection, these models also have a manual temperature control operated by a single lever on the side of the body. The inlet hoses incorporate a stainless steel strainer (M10, GC10, MX10, A10 & L10 model variants) or combined TPE washer and stainless strainer (M20, GC20, A20 & L20 model variants). The models are supplied with or without a pop-up waste. The M20, GC20 A20 & L20 model variants are single feed. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Single hole, single outlet (fixed), electronically operated tap assembly. The flow is controlled by a solenoid valve and activated via an infra-red sensor. Inlets are supplied with check valves (verified by test - suitable for backflow protection against fluid category 2). Maximum working pressure 6 bar. Maximum operating temperature 40 °C
Range of deck mounted, Infra-red electronic basin mixers with mixing device and adjustable temperature limiter. The tap incorporates EPDM O-rings. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C
Side entry BS1212-4 (2016) compact type float operated valves for use with WC flushing cisterns. The inlet incorporates a strainer. Maximum working pressure 10.0 bar. Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
BS1212-4 (2016) compact type float operated valve for WC flushing cisterns, side entry type. The inlet incorporates a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Range of side and bottom entry BS1212-3 inlet valves, with plastic bodies and brass shanks. Maximum working pressure: 3.0 Bar low pressure and 14.0 bar high pressure Maximum operating temperature: Cold water use only.
Range of concealed WC flushing cisterns with a side entry BS 1212-4(2016) float operated inlet valve providing a type AG air gap arrangement and a dual flush outlet valve. The flush volume is operated by a two button assembly for a 6 or 3 litre flush volume. The cistern incorporates a servicing valve and a stainless-steel braided EPDM lined flexible hose assembly installed prior to the inlet valve. Maximum working pressure 10.0 Bar, Cold Water use only
Range of ceramic disc headworks with brass bodies and NBR ‘O’-rings. Maximum working pressure 10.0 Bar. Maximum operating temperature 85.0°C.
Single-hole, single outlet (swivel) combination tap assemblies (brass body – various finishes) incorporating a ceramic cartridge (F1054-**) or quarter turn ceramic disc (F1046-**) headwork with a single lever operating member. The products have a pull-out spray outlet which incorporates a plastic aerator and trigger mechanism that stops the flow (model (F1046-**) or changes the water pattern from straight flow to spray (F1054-**). Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating a ceramic cartridge headwork with single lever type operating member. The spout outlet incorporates a plastic flow straightener. Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C.
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass), incorporating quarter turn ceramic disc headworks with cross-top operating members. The spout outlet incorporates plastic flow straighteners. The products incorporate lever operated pop-up wastes (not verified by test). Maximum operating pressure 10.0 bar. Maximum operating temperature 65°C.
Range of single-hole, single outlet fixed combination tap assemblies (chrome plated brass bodies), incorporating ceramic cartridge headworks with single lever type operating members. The spout outlet incorporates plastic flow straighteners or for model OPS BAS C an aerator with 4.5lpm flow limiter - flow limiter performance is not tested as part of the regulators specification. Products are supplied with click-type pop-up wastes (verified by test). Maximum operating pressure 5.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener or a plastic aerator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Single hole, single outlet, fixed combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic flow straightener and an optional flow regulator. Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The products are supplied with click type pop up waste (verified by test). Maximum working pressure 5.0 Bar. Maximum operating temperature 60°C
Floor mounted single hole, single outlet (fixed) combination tap assembly (brass bodies -various finishes). Incorporating a ceramic cartridge headwork with a single lever operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of floor mounted single hole, single outlet (fixed) combination tap assemblies (brass bodies - various finishes). Incorporating a ceramic cartridge headwork with a single lever type operating member and a self-cancelling diverter to shower outlet. The spout outlet incorporates a plastic aerator. The shower outlet connection incorporates an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating pressure 10 bar. Maximum operating temperature 60°C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies - various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 65.0°C
Range of two hole, deck mounted, single outlet fixed combination tap assemblies incorporating quarter turn ceramic disc headworks with single lever operating members. Models XB-SL-046 and 079 incorporate plastic aerators, models XB-SL-049, 051 and 053 incorporate plastic flow straighteners. The products are supplied with metal back nuts. Maximum working pressure 10.0 bar. Maximum operating temperature for XB-SL-038 85oC, all other models are 65⁰C.
Range of wall mounted, two-hole, single outlet (fixed) combination tap assemblies, (brass bodies - various finishes), incorporating a ceramic cartridge headwork with single lever operating members and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. Both inlets incorporate stainless steel strainers and approved check valve cartridges however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of two-hole, single outlet (fixed) combination tap assemblies (brass bodies - various models), incorporating quarter turn ceramic disc headworks with cross top or single lever operating members and a manually operated diverter to shower outlet. Maximum working pressure 5.0 Bar Maximum operating temperature 65.0°C
Two-hole, single outlet (fixed) combination tap assembly (chrome plated brass), incorporating quarter turn ceramic disc headworks with single lever operating members and a self-cancelling diverter to the shower outlet. The spout outlet incorporates a plastic flow straightener. The product is supplied with a shower hose and handset and metal back nuts. Models VAL2 BSM E6 C CD & VAL2 BSM E8 C CD come supplied with flow restrictors. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Range of wall mounted, two-hole, single outlet (swivel), combination tap assemblies (chromium plated brass) incorporating ceramic cartridge headworks with single lever operating members. The spot outlet incorporates a plastic flow straightener. The offset unions of models 2445, 2445L, 2445EP & 2445LEP incorporate a concentric isolation valve. Model 2445EPS incorporates an approved check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection and a flow regulator. Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC.
Range of wall mounted, two-hole, single outlet (swivel) combination tap assemblies (chromium plated brass) incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator, and the products are supplied with metal backnuts. Maximum working pressure 8.62 Bar Maximum operating temperature 60.0°C
Page 79 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
