Range of wall mounted thermostatic shower valves (chrome plated brass bodies) incorporating a two-way diverter valve controlling the flow between shower outlets with a dome type operating member. The temperature is controlled independently via a thermostatic cartridge with a dome type operating member with manual override button. Both inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of wall mounted thermostatic blending valve (chromium plated brass incorporating a quarter turn ceramic disc headwork. The temperature is controlled independently via a thermostatic cartridge incorporating a manual override button. The inlets incorporate approved check valve cartridge(s), however, the complete product has not been fully tested to demonstrate it provides backflow protection and stainless steel strainers. Maximum working pressure 5.0 bar. Maximum operating temperature is 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
Range of gear or lever operated wafer, semi lugged or fully lugged butterfly valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seats. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated or nickel plated ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Range of lugged and wafer type butterfly valves with blue epoxy coated bodies, incorporating EPDM rubber ‘O’-rings and seat, and either a bronze (AB2), stainless steel (CF8 & CF8M) or blue epoxy coated ductile iron (DI) disc. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C.
Three-way diverter valve with a stainless-steel body and stainless-steel ball. Maximum working pressure 9.8 bar Maximum operating temperature 80°C.
‘Mark II’ range of equilibrium float operated valves with gunmetal bodies, incorporating EPDM rubber washers and NBR rubber ‘O’-rings and washers. QA102: 1” & 2” models also incorporate a fibre washer. Maximum operating pressure 10.0 bar. For cold water use only.
‘Mark I’ range of equilibrium float operated valves with gunmetal bodies, incorporating EPDM rubber washers and NBR rubber ‘O’-rings and washers. QA102: ½” - 1½” models also incorporate a fibre washer. Maximum operating pressure 5.0 bar. For cold water use only.
Range of spring-loaded resilient trim, non-return valves with blue epoxy coated ductile iron bodies, stainless steel discs and EPDM seals. Maximum working pressure 16.0 bar. Maximum operating temperature 80°C.
Range of in line adjustable pressure reducing valves with (brushed chrome plated) DZR brass bodies for use with copper pipe manufactured to EN1057. The valves incorporate stainless steel strainers and are supplied with pressure gauges. Maximum supply pressure 16.0 bar. Outlet pressures are adjustable between 1.0 and 6.0 bar. Maximum operating temperature 85°C
EV220 BW range of normally closed solenoid valves with brass bodies, EPDM diaphragms and ‘O’-rings and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of spherical valves with DZR brass bodies, chrome plated brass ball and PTFE seats with tee-handles or lever type or extension stem type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of spherical valves with brushed chrome brass bodies, chrome plated brass ball incorporating a PTFE seat and NBR O rings. For use with EN1057 copper pipe. Maximum working pressure 25.0 bar. Maximum operating temperature 85°C
Range of spherical isolation valves incorporating brass bodies (nickel plated), brass ball (chrome plated), brass stem and EPDM ‘O’-rings (screwdriver operated or T-type handle). For use with copper pipe (EN1057). Maximum working pressure 16.0 bar (model 10.60982.015.CP12-8510) Maximum working pressure 25.0 bar (model 10.62022.015.CP12-8510) Maximum working pressure 40.0 bar (models 10.61062.015.CP12-8510 & 10.61062.022.CP12-8510) Maximum operating temperature 85°C.
Range of inline or angled ball valves with brass or nickel-plated brass bodies, chrome plated brass balls and a lever, butterfly or lockshield operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of spherical valves with DZR brass bodies, chrome plated brass ball and PTFE seats with tee-handles or lever type or extension stem type operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of gate valves incorporating a blue epoxy coated cast iron body, EPDM gate and seals and a non-rising stem with a handwheel operating member Maximum working pressure 16.0 bar, Maximum operating temperature 85ºC.
‘KHS CoolFlow’ range of cold water thermostatic balancing valves, incorporating gunmetal bodies,PTFE seats and EPDM ‘O’-rings. The 6150G01500 and 6160G01500 models are servo controlled (230V and 24V respectively), the 6170G01500 model is manually controlled. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of UV disinfection units with stainless steel bodies & quartz tubes. All models incorporate a spherical valve on the drain outlet. Maximum working pressure 16.0 bar. Maximum operating temperature 50°C
Range of UV disinfection units with stainless steel bodies and EPDM seals. The UV lamps are housed inside quartz tubes. Maximum working pressure 10.3 bar. Maximum operating temperature 40°C.
'M9000'. Grey coloured, injection moulded POM material. For use with water up to 85°C.
'Delrin® RAFG511DP NC010'. White coloured, injection moulded semi-opaque acetal material. For use with water up to 85°C.
'JPC Liquid Epoxy Paint'. Factory applied, red coloured, two-component epoxy paint. Mix components A & B in a 3:1 volume ratio and apply as per manufacturer's instructions ' JPC-FG-A/06-21/009 & JPC-FG-B/06-21/009' dated '02/06/2021'. Cure for 7 days@34°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'KARUMEL EX4412 (RAL5005) & KARUMEL EX4412 (Blue)'. Factory applied, blue coloured epoxy powder coatings. Apply as per manufacturer's application guide for potable water reference number 'KCSA-21090101' dated September 2021. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LNXFSY'. Factory applied, grey coloured Portland Cement Mortar. Mix cement, sand and water in a 2:1:0.4 mass ratio and apply as per manufacturer's instructions issue 'X202101207F' dated '2021-12-07'. Cure for 12 hours@55°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Ya-Coat Amiantit (SADIP)'. Factory applied, two-component, green coloured (once mixed and applied) PU coating. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's process document 'MW 106-5 issue 1', dated 26/06/2007. Cure for 10 minutes@35°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Desmopol DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS 'DESMOPOL DW v.11-03-2022'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote® 48-20'. Factory applied, blue coloured, two component epoxy coating consisting of a resin and hardener. Mix resin and hardener in a mass ratio of 68:32 and apply as per manufacturer's TDS dated 10/12/2018. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 1555'. Factory applied, dark blue/grey coloured vitreous enamel coating. Apply as per manufacturer's instructions 'I.PBE.06.04' dated November 22, 2021 and 'TPE.09.056.02' dated August 19, 2014. Cure for 14 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterSeal P693/94Primer and MasterSeal M 649 (formerly known as MasterSeal 694) Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply 'MasterSeal P693/94Primer’ as per Technical Data Sheet ‘MBS_CC-UAE/Sl_P_693/694_06_22’. Cure for 2 hours@25°C. Then mix and apply ‘MasterSeal M 649 Coating' as per Technical Data Sheet ‘MBS_CC-UAE/Sl_M 649_06_21/v1/08_21/v2/06_22/v3/10_22’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resichem 507 DWPU Blue & Grey'. Site applied, two-component polyurethane coatings which are available in blue or grey colours (once mixed). Mix Part A (blue or grey opaque liquid) with Part B (amber, translucent liquid) in a 100:30.5 weight ratio and apply as per manufacturer's technical data sheet 'TDS507DWPU.rv4.09062022'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'YT-002 (natural) & YT-003 (black)'. Extruded, natural (colourless) or black coloured PVC hoses. For use with water up to 65°C.
'Purolite C107E'. Cream coloured ion exchange resin. For use with water up to 23°C.
'Purolite A520E'. Light brown coloured ion exchange resin. For use with water up to 23°C.
'Purolite® C104E/5264'. Cream coloured ion exchange resin. For use with water up to 23°C.
'K422'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'May 2022'. For use with water up to 85°C.
'Hydro 90'. Clear, silicone lubricant aerosol. Apply as per manufacturer's instructions 'version 1.0' dated 'June 2022'. For use with water up to 85°C.
'Bestnyl SI40VI02BD (PA 640GF BK)'. Black coloured, injection moulded PA6 material. For use with water up to 60°C.
'KN133G50 (beige coloured) & KN133G50BL (black coloured)'. Injection moulded PA6 materials. For use with water up to 65°C.
'DH-01 Pipe'. Blue coloured, extruded HDPE pipe. For use with water up to 65°C.
'DH-02 Fitting'. Blue coloured, injection moulded HDPE fitting. For use with water up to 65°C.
`Hydro Dynamic PE100 Pipes`. Black coloured, extruded polyethylene pipes. For use with water up to 60°C.
'Shield PE100 Segmented Fittings'. Black coloured fittings manufactured by extrusion and butt-fusion. For use with water up to 85°C.
'DURAFIDE® 1140A1 WF9050 & DURAFIDE® 1140A1 WK9050'. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
‘FORTRON 9115L0 SD3039 BLACK (formerly known as FORTRON MT9115L0 SD3039 DW black) & FORTRON 9141L4 SD3039 BLACK (formerly known as FORTRON MT9141L4 SD3039 DW black’). Black coloured, injection moulded PPS materials. For use with water up to 85°C.
‘RTP 199 X 146499 S-202865 White’. White coloured (opaque), injection moulded PP material. For use with water up to 50°C.
'Tamkeen Modern Pipe White, Light Grey and Dark Grey'. Extruded PVC pipes. For use with water up to 60°C.
‘Chemfix PESF TOP’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Chemfix Polyester Styrene Free', rev. 1 dated 03/02/2022. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 75 of 225
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
