Range of double regulating valves incorporating bronze bodies with two test ports. Valves are adjusted using a handwheel. Maximum operating pressure: 25 bar. Maximum operating temperature: 85°C.
Stuart CM range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
UV disinfection unit with stainless steel body. Maximum working pressure 9.0 bar. Maximum operating temperature 55°C.
Range of UV disinfection units with stainless steel bodies. Maximum working pressure 10.3 bar. Maximum operating temperature 60°C.
'Edelpoxy FN TM 142'. Factory coloured, red coloured epoxy resin coating consisting of a base and hardener. Mix base and hardener in a 3:1 volume ratio and apply as per manufacturer's IFU 'PCC/ PC 142', dated '10.07.2018'. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sigmaline 523'. Factory applied, two-component, yellow coloured or red/brown coloured epoxy coatings. Mix and apply in accordance with Product Data Sheet ref. 7623 dated February 4, 2021. Cure for 3 days@23°C. The red-brown coloured coating is for use with water up to 60°C. Between June 2024 and March 2025, the yellow-coloured coating is for use with water up to 23°C. Between April 2025 and June 2029, the yellow-coloured coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV17'. Factory applied, blue coloured, two-component epoxy coating. Mix coating and hardener in a weight ratio of 4:1 or volume ratio of 3:1 and apply as per manufacturer's TDS '01 – 11.06.2024'. Cure for 7 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Truform Cement OPC 43 Grade'. Factory applied, grey coloured cement. Mix cement:sand in a weight ratio of 2:1 and add 0.5 litres of water. Apply as per manufacturer's instructions 'TTPL/SOP/MCD/03', revision '00', dated 01.04.2018. Cure for 24 hours@27°C followed by 7 days@85°C. For use with water up to 85°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SIGMACOVER 280 (Yellow/Green) + SIGMAGUARD CSF 650 (Green)'. Factory applied, light green coloured (once applied), epoxy primer & coating. Mix base and hardener of SIGMACOVER 280 in a 4:1 volume ratio and apply as per manufacturer's PDS '7417', dated 'May 23 2024'. Cure for 24 hours@20°C. Mix base and hardener of SIGMAGUARD CSF 650 in an 80:20 volume ratio and apply as per manufacturer's PDS '7443', dated 'July 26, 2022'. Cure for 5 days@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikalastic® M689 AE (formerly known MasterSeal® M689AE)'. Factory applied, two-component, light grey coloured (once applied), polyurea coating. Mix parts A & B in a volume ratio of 1:1 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Sl_M689_06_20/v9/07_23/v10/01_24/v11/03_24'. Cure for 7 days@25°C. For use with water up to 70°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'LMI.Hygienic HI-Build Epoxy'. Factory applied, two- component, blue coloured epoxy coating. Mix base and hardener in a weight ratio of 100:15 and apply as per manufacturer's instructions 'LMIEP1403032', dated '22/06/2024'. Cure for 2 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Sikadur® ADH2200 (formerly known MasterBrace® ADH2200)'. Site applied, grey coloured (once applied), two component Epoxy bedding and mortar. Mix parts A and B in a weight ratio of 60:40 and apply as per manufacturer's Product Data Sheet 'MBS_CC-UAE/Br_2200_12_94/v4/07_19/v5/05_20/v6/01_24/v7/03_24'. Cure for 21 days@25°C. For use with water up to 40°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purolite C104EPLUS'. Cream coloured ion exchange resin. For use with water up to 23°C.
'ULTRADUR® B4300 G6 FC AQUA WHITE 25262 & ULTRADUR® B4300 G6 FC AQUA BLACK 15142'. White coloured & black coloured, injection moulded PBT materials. For use with water up to 85°C.
'Ultradur® B4520 FC Aqua uncolored'. Uncoloured (appears white), injection moulded PBT materials. For use with water up to 23°C.
'Cool-FIT 4.0 & 2.0 Pipes'. Triple layered, extruded polyethylene pipe which comprises of a black coloured inner layer, off-white coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'Cool-FIT 4.0 & 2.0 Fittings'. Triple layered, injection moulded electrofusion fittings which comprise of black coloured inner layer, ivory coloured insulation layer and black coloured outer layer. For use with water up to 65°C.
'VIALLI-De SDR 6 & SDR 7.4 PPR pipes'. Green coloured, extruded PPR pipes. For use with water up to 85°C.
'VIALLI-De PPR SDR 6 & SDR 7.4 Pipes with Glass Fibre Middle Layer'. Extruded PPR pipes with a green coloured inner and outer layer and a red coloured, glass fibre middle layer. For use with water up to 23°C.
'Ultrason® S 2010 G4'. Light beige coloured, injection moulded polysulphone material. For use with water up to 85°C
'IROGRAN® A 85 P 4441 FCM'. White coloured, injection moulded polyurethane material. For use with water up to 60°C.
'IROGRAN® A 85 P 4394 FCM'. Clear (colourless), injection moulded polyurethane material. For use with water up to 60°C.
‘D-TECH DTCAPOL-300’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions dated 29.01.2021. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'D-TECH DTCAVYN-300'. 'D-TECH DTCAVYN-420' was added to the approval in July 2024. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resins. Apply as per manufacturer's instructions dated 01.07.2024. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XB/300'. Black coloured, compression moulded butyl (IIR) material. Shore hardness 58 ShA. Tested in-radius size 1.24mm. For use with water up to 23°C.
'9710 'O' Rings'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 75. Tested in-radius size between 0.5mm & 3.4mm. For use with water up to 85°C.
Initial approval was for ‘SMS-80’ (shore hardness 80) only. In April 2024 ‘SMS-50' (shore hardness 50) & ‘SMS-70’(shore hardness 70) were added to the approval. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 23°C.
'AEC 2/EPDM-50, AEC 3/EPDM-60, AEC 4/EPDM-70 & AEC.A5/EPDM-80'. Black coloured, compression moulded EPDM materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'EDXX 74'. Black coloured, compression moulded EPDM material. Shore hardness 75. Tested in-radius size 1.5mm. For use with water up to 85°C.
'6741'. Brown coloured, compression moulded FKM material. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 85°C.
'TH5/01/4 BLK Diaphragm Seal'. Black coloured, injection moulded HNBR diaphragm seal. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'PLIMAT ABS PRESSURE Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BOSS PRESSURE ABS Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DURAPIPE One Step ABS Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EFFAST ABS PRESSURE Solvent Cement'. Grey coloured solvent cement intended to join ABS pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'BOSS PRESSURE PVC Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DURAPIPE RH PVC-U Solvent Cement'. Amber coloured solvent cement intended to join PVC pipe and fittings. Apply as per manufacturer's instructions. Cure for 24 hours@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'RIAMAXX HR XE4349 KTW natur. RIAMAXX HR XE4349 KTW schwarz. RIAMAXX HR XE4350 KTW natur. RIAMAXX HR XE4350 KTW schwarz. RIAMAXX HR XE4351 KTW natur. RIAMAXX HR XE4351 KTW schwarz. RIAMAXX HR XE4352 KTW natur. RIAMAXX HR XE4352 KTW schwarz'. Natural (appears beige) and black coloured, injection moulded Polyketone materials. For use with water up to 85°C.
'RIAMAXX HR GF40 Xgea14 KTW schwarz'. Black coloured, injection moulded Polyketone material. For use with water up to 85°C.
Wall mounted electric heater, incorporate a manually operated push button valve controlling the flow and plastic strainer on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Range of BS1212-4 (2016) compact type float operated valves for WC flushing cisterns, bottom or side entry type with brass ½’’ or ¾” BSP inlet. The inlet incorporates a strainer, models incorporate a delay fill function. The bottom entry valves are height adjustable. Maximum working pressure - 10 Bar, Cold water use only.
Range of spring loaded resilient trim check valve cartridges with plastic bodies, stainless steel spring and EPDM ‘O’-rings. For insertion into fittings with specifically sized bores. Maximum working pressure 16 Bar Maximum operating temperature 65°C (model OV15/DN15-EPDM 31.0001.0 only) Maximum operating temperature 85°C for all other models
Spring loaded in-line check valve cartridges for insertion into pipes and fittings with specifically sized bores. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Assisted bath incorporating a thermostatic mixing valve to control both the flow and temperature to either a spout outlet or shower handset. The discharge from the bath spout and shower handset in via a type AUK 3 airgap, verified by measurement, suitable for Fluid Category 5 backflow protection. The bath has adjustable height and tilt functions. Maximum working pressure: 6 Bar Maximum operating temperature: 45 °C
Single hole, single outlet (swivel) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The outlet is a pull-out spray type and incorporates a plastic aerator. Maximum working pressure 10.0 Bar Maximum operating temperature 60.0°C
Range of single-hole, single outlet (swivel) combination tap assemblies (chrome plated brass bodies) incorporating a ceramic cartridge headworks with single lever operating members. The product incorporates a pull-down hose incorporating plastic aerators and a trigger mechanism. Maximum working pressure 5.0 Bar. Maximum operating temperature 60.0°C
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 65°C
Range of single-hole, single outlet (fixed) combination tap assemblies (brass bodies – various finishes), incorporating ceramic cartridges and quarter turn ceramic discs headworks with single lever or dome type operating members. The spout outlets are either open outlet, waterfall or incorporate plastic aerators. Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW104101110xx, TVW103004000xx, TVW125001000xx) are supplied with lever operated pop-up wastes (not verified by test). Models (TVW103005000xx, TVW104105110xx & TVW125002000xx) are supplied with click type pop-up wastes (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Range of deck mounted, single-holed, single outlet (fixed) combination tap assemblies (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate plastic aerators. Models (TVW105002000xx, TVW105003000xx, TVW105101110xx & TVW105141110xx) are supplied with lever operated pop-up wastes (not verified by test) Model TVW105105110xx) is supplied with a click type pop-up waste (verified by test). Maximum working pressure 10.0 Bar. Maximum operating temperature 60°C.
Page 73 of 131
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
