‘MagCat’ range of in-line water conditioners with stainless steel bodies and catalytic alloy core. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of inline water conditioners with zinc/copper alloy bodies. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 80°C
Range of combined isolation and drain off valves with brass bodies and EPDM O-rings. Maximum working pressure 16 Bar Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
'DURACON®M90-44 WK3068'. Black coloured, injection moulded POM material. For use with water up to 85°C.
'KEPITAL F10-03H BBK & KEPITAL F10-03H BK'. Black coloured, injection moulded POM materials. For use with water up to 85°C. 'KEPITAL F10-52H'. Natural (appears white), injection moulded POM material. For use with water up to 40°C.
'TIANYI SUNS-012'. Factory applied, black coloured, bituminous coating. Apply as per manufacturer's user instructions 'File No.: Tianyi Suns-0024, Version: TYS-03, Date of issue: 2021-05-05'. Cure for 2 hours @60°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valcoat Blue'. Factory applied, blue coloured epoxy coating. Pre-heat the substrate and apply as per manufacturer's TDS with issue '01.04.2023'. Post-cure for 5-7 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'TM-cement-01'. Factory applied, grey coloured cement. Mix sand/cement/water in a weight ratio of 1.7:1.0:0.74 and apply as per manufacturer's instructions 'TM20231122-A0', dated 2023-11-22. Cure for 6 hours@25°C (±2°C). Between November 2023 and November 2024, the material was for use with water up to 23°C. Between December 2024 and November 2028, the material is for use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cleantech PW'. Factory applied, two-component, red coloured epoxy coating. Mix component A and component B in a volume ratio of 3:1 and apply as per manufacturer's product data sheet 'CCPL/TDS/R11/CRC/17-18/04/R6/spray'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured fusion bonded epoxy powder coating. Apply as per manufacturer's Product Information '704G_TDS', revised 'August 16,2022'. Post-cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the post-curing conditions that appear on the approval. If the post-cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'CY7000 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instruction manual 'YS-QNS-WZBC-2021W', dated 'May 20, 2021'. Cure for 15 minutes@180°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'C21 Dyopox PTW White'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated '2011'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Planiflex PF41'. Green coloured fibre sheet material manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/material having been tested at a reduced surface area to volume ratio. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
'Tecnoplast GRVE pipe'. Translucent, light green coloured, GRP pipe manufactured by hand lay-up. For use with water up to 23°C. From July 2024 the pipe is for use with water up to 60°C.
'Akoalit PB 4237 and Akoalit PB 4238 White'. Grey or white coloured, extruded PB materials. For use with water up to 85°C.
'LK PE-Xa pipe'. The pipes are either single layered or multi-layered (3 or 4 layers). The single layered, extruded pipes are natural (off-white coloured) PE-Xa. The multi-layered, extruded and IR cross-linked pipes have a natural (off-white coloured) PE-Xa inner layer, an adhesive layer, an oxygen barrier layer based on EVOH and then an optional 4th, adhesive layer. All are for use with water up to 85°C.
'BWRB1620200'. In July 2024 the following pipes were added to the approval: ‘BWRB1620100, BWRB2020200, BTRB2525100 & BTRB3230100. Triple layered, extruded pipes consisting of an off-white coloured PERT inner layer, aluminium middle layer and white coloured PERT outer layer. For use with water up to 85°C.
‘Drinkflex Aquarius 3G1, 3G1,5, 3G2,5, 3G4, 4G1, 4G1,5, 4G2,5, 4G4 & 4G6’ range of polyolefine cables. The cables have an extruded, blue coloured polyolefine outer (water contact) layer and are available with 3 or 4 internal cores. For use with water up to 23°C.
'PTFE G453'. Black coloured, extruded PTFE material. For use with water up to 85°C.
'RRS 502B GR1500'. In February 2025, ‘RRA 410B GR1500’ was added to the approval. Dark grey coloured, injection moulded PVC materials. For use with water up to 23°C.
'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'EP70 BLK Seals'. Black coloured, injection moulded EPDM seals. Shore hardness 70. Tested in-radius size 1.0mm. In April 2024, 'EP70 BLK 'O' rings’, black coloured, injection moulded 'O' rings were added to the approval. Shore hardness 70. Tested in-radius size of 1.3mm For use with water up to 85°C.
'334137 – EPDM Peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'PT0469'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EPDM HT5697-4A'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. Between May 2024 and October 2024, the material was for use with water up to 50°C. Between November 2024 and May 2029, the material is for use with water up to 60°C.
‘ME0996’ components. Black coloured, injection moulded NBR rubber components. ‘O’-rings with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. Between November 2023 and April 2024, the approval included gaskets with an in-radius size of 5.0mm. Shore hardness 40. From May 2024 the gasket range was extended to include gaskets with an in-radius size of between 0.5mm & 5.0mm. Shore hardness between 40 & 90. For use with water up to 23°C.
‘LS40T-0301, LS50T-0301, LS60T-0301, LS70T-0301 & LS80T-0301’. Injection moulded, liquid silicone rubber sheet material, available in white, grey, black, blue, green, natural (unpigmented) & red colours. Shore hardness between 40SH-A & 80SH-A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'kSil GP200, kSil GP250, kSil GP350, kSil GP400, kSil GP450 & kSil GP530'. Pale yellow/white coloured, extruded silicone rubber cellular sponge materials. Shore hardness between 37 & 70. Tested in-radii sizes between 1.53mm & 1.76mm. For use with water up to 85°C.
'Loctite 648'. Dark green coloured anaerobic adhesive. This product is to be applied and cured in strict accordance with the manufacturer’s instructions. For use with water up to 85°C.
'POKETONE’ range of natural (appears light brown), grey and black, injection moulded Polyketone materials. For use with water up to 85°C. 'M(a)3FG(b)A-NP0, M(a)3FG(b)A-GY(c), M(a)3FG(b)A-BK(c)'. (a) indicates the MI(g/min) or viscosity of its neat resin and is replaced with: 9 = 150~250, 3 = 40~80, 6 - 4~8 or 7 = 2~4. (b) indicates the content of glass fibre and is replaced numbers between 1 & 9 (9 indicating the maximum of 50%). NP0 indicates natural material, GY indicates grey material & BK indicates black material. (c) can indicate a random product number of each grade OR the ratio of carbon black and is replaced with numbers between 0 & 9.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
'AMIANTIT DARK GREY AA PIPE and AMIANTIT ORANGE BB PIPE'. Dark grey coloured or orange coloured, extruded PVC pipes. For use with water up to 45°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel or brass bodies – various finishes). Flow is controlled via solenoid valve (housed in a control box) actuated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The spout outlets incorporates plastic aerators. The products incorporate a stainless steel PEX lined flexible hose assembly, connecting the tap to the solenoid valve. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and model AF 1602 incorporates a plastic aerator in the spout outlet. Maximum working pressure 8.0 Bar Maximum operating temperature 45.0°C
Single hole, single outlet (fixed) electronically controlled, combination tap assemblies (chromium plated brass). Flow is controlled via solenoid valves, actuated by infra-red sensors. Temperature is controlled independently using a single lever operating member on the side of the body. The spout outlets incorporate plastic aerators. Maximum working pressure 8 Bar Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (stainless steel bodies), incorporating a solenoid valve controlling the flow which is actuated via an infra-red sensor. The spout outlet incorporates a plastic aerator. The product also incorporates an integral hand dryer. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 43°C
WC flushing cistern incorporating a side entry BS 1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush valve for full flush volumes of up to 6 litres and a reduced flush of up to 4 litres. The cistern is operated by a manual push button and incorporates a servicing valve and flexible hose on the inlet supply. Maximum working pressure 10.0 bar. Cold water use only.
Range of floor mounted, single-hole, single outlet (fixed), combination tap assemblies (chromium plated brass bodies), incorporating a ceramic cartridge headwork with a single lever operating member and a manual diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Maximum working pressure 5 bar. Maximum operating temperature 85°C
Range of Type TK spring loaded, resilient trim, in-line check valve cartridges. For insertion into specifically dimensioned bores. Maximum working pressure 10.0bar. Maximum operating temperature 65ºC.
Range of single hole, single outlet (swivel nozzle) tap (chrome plated brass) incorporating ceramic cartridge headwork with single lever operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 10 bar. Maximum operating temperature 60°C.
Flow regulator incorporating a plastic body and EPDM O-ring. Maximum operating temperature 65.0°C.
Range of quarter turn ceramic disc headworks with brass bodies, intended for insertion into specifically dimensioned tap assemblies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of ceramic cartridge headworks with plastic bodies incorporating silicone seals, for insertion into specifically dimensioned bodies. Maximum working pressure 10.0 bar. Maximum working temperature 85°C.
Range of single hole, single outlet (swivel) combination tap assemblies (brass bodies, various finishes - see model) incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlet is a pull-out spray type which incorporates a nylon braided flexible hose incorporating a dual layer inner hose consisting of PEX inner layer and HDPE outer layer, and a manually operated button to divert between a plastic aerator and the spray function. The spray handset incorporates an approved check valve cartridge with an integral plastic flow regulator, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 6.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet (swivel) combination tap assemblies with (brass bodies -various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator.and a pull out spray feature. The connection between the outlet and the hose incorporates an approved single check valve cartridge, however, the complete product has not been fully tested to demonstrate that it provides backflow protection Maximum working pressure 7 bar. Maximum operating temperature 65ºC.
Single hole, single outlet (fixed) combination tap assembly (brass bodies – various finishes) incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates a plastic aerator. The product is supplied with a lever operated pop up waste. Maximum working pressure 5 bar. Maximum operating temperature 70 °C
Range of pillar taps, (chrome plated, brass bodies), incorporating quarter turn ceramic disc headworks with single lever operating members. The spout outlets incorporate plastic flow straighteners. The products are supplied with metal back nuts. Maximum operating pressure 6 bar. Maximum operating temperature 85°C
Range of single hole, single outlet, fixed combination tap assembly, (chrome plated brass bodies) incorporating ceramic cartridge headworks with single lever operating members. The spout outlets incorporate aerators and plastic flow straighteners. The products are supplied with a click type pop-up waste. Maximum working pressure 16 bar. Maximum operating temperature 60°C
Page 71 of 125
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
