Range of spherical valves with nickel platedbrass bodies, nickel plated brass balls and EDPM ‘O’-rings with a lever type operating member. Maximum working pressure 50.0 bar. Maximum operating temperature 85°C.
Range of spherical valves with a brass body brass ball (chrome plated), PTFE gaskets, EPDM ‘O’-rings and a single lever operating member. Maximum working pressure 10.0 bar. Maximum working temperature 100°C.
Range of spherical ball valves with lever or tee operating member, brass bodies, chromium plated brass ball and PTFE seat. Maximum working pressure 50.0 bar: ¼” (DN 8), 3/8” (DN 10) & ½” (DN 15). Maximum working pressure 40.0 bar: ¾” (DN 20) & 1” (DN 25). Maximum working pressure 30.0 bar: 1¼” (DN 32) & 1½” (DN 40). Maximum working pressure 25.0 bar: 2” (DN 50). Maximum operating temperature 60°C.
Range of gate valves with DZR brass bodies and brass wedge. Valves are operated via a non-rising spindle headwork. Maximum operating pressure 20.0 Bar. Maximum operating temperature 100°C.
Range of gate valves (gunmetal) with gunmetal bronze wedges, brass spindle and PTFE seals. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of hand wheel operated gate valves with bronze bodies, bronze wedges, non rising spindles and graphite gaskets. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of gate valves with bronze bodies and wedge with PTFE packing. The valves operate via a non-rising spindle headworks that incorporates a hand wheel type operating member. Maximum working pressure 25.0 Bar. Maximum operating temperature 85°C.
Range of gate valves incorporating a blue epoxy coated ductile iron body. EPDM coated ductile iron wedges and a non-rising spindle headwork. Maximum working pressure 16.0 bar. Maximum operating temperature 45°C. As of September 2024 Maximum operating temperature 23°C.
Range of screw down stop valves incorporating brass bodies and EPDM gaskets. Maximum working pressure 16.0 bar. Maximum working temperature 80°C.
Range of bedpan washers with the flow controlled by a solenoid valve and discharged via a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). Maximum working pressure 6.0 bar. Maximum operating temperature 60°C
Range of magnetic scale inhibitors incorporating nickel plated copper bodies. Maximum working pressure 10.0 bar. Cold water use only.
Electrolytic scale inhibitor incorporating a nickel plated copper body. Maximum working pressure 10.0 bar. Cold water use only.
'Birla SRPC - Electrocement'. Factory applied, grey coloured, cement mortar. Mix cement, sand & water in a mass ratio of 0.6:1.0:0.22. Cure for 24 hours@27°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'Jotapipe IL6001 50S'. Factory applied, blue coloured, fusion bonded epoxy coating. Apply as per technical data sheet dated '10 September 2019'. Cure for 15 minutes@230°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EDELPOXY FN 132 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's IFU reference 'PC 132' dated 'January 28, 2020'. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aixin Powder Coating RAL 5015 Blue'. Factory applied, blue coloured EP coating comprising of base, hardener, pigment, filler and additive agent. The base, hardener, pigment, filler and additive agent were mixed in a 60:12:10:17:1 mass ratio. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Eurokote® 46-60 Red Brown'. Factory applied, red-brown coloured epoxy coating. Apply as per manufacturer's technical data sheet dated 19/11/2019. Cure for 7 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPY2-II'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's user instruction 'REV-202012-2' dated '11.12.2020'. Cure for 7 minutes@180°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC4'. Factory applied, clear PTFE coating, intended for use with `O` rings, seals & gaskets. Apply as `Superior Group Quality Management System Procedure Reference 8.6’ referenced in document `LDAP-008 issue 1` released 01/05/2020. For use with water up to 85°C
Page 8 of 577
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
