Silver and copper disinfection ion generator with a plastic body, incorporating a plastic flow switch. Maximum working pressure 9.0 bar. For cold water use only
Range of polyethylene pressure vessels with spun (blue) fibre glass casing. Maximum working pressure 10.0 bar. Maximum operating temperature 50°C.
‘Hostaform® C9021 ECO-B NATURAL, C9021, M15HP, C2521, C13021, C13031, C27021 ECO-B NATURAL, C27021, C52021 & M90JG’. Injection moulded, natural (which appear to be white) acetal materials available in the following colours: Black 14 DW (formerly known as Black 14), White 22, Grey 33, Grey 36, Grey 39, Red 46, Red 47, Yellow 56, Brown 65, Green 76, Blue 87, RAL 2010, RAL 4008 & RAL 5005. Customer specific colours may also be provided with a nomenclature following the structure ‘xx/yyyy DW’ where ‘yyyy’ denotes the specific colour shade, ‘DW’ denotes ‘Drinking Water’ & ‘xx’ denotes 10 – black, 20 - white (incl. Cream, 30 – grey, 40 – red (incl. Pink), 50 – yellow, 60 – brown (incl. Beige), 70 – Green & 80 – blue. For use with water up to 65°C.
'PMSP5105-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
`Jotaguard VA 5001`. Factory applied, dark blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturers test method document no. '39.40.014', issue date '02.01.2018', revision no. '02'. For use with water up to 85°C.
'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Acrylatik'. Site applied, Acrylate primers available in white, red, blue and black colours. Apply as per manufacturer's instructions 'Appendix No. 1, TU 2316-002-92 872914-2016' dated '11.02.2016'. Cure for 20 minutes@20°C and then 20 minutes@90°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Purolite® A600E/9149'. Yellow coloured ion exchange resin. For use with water up to 23°C.
AKROMID® A3 GF 25 8 HU natural (8120) AKROMID® A3 GF 30 8 HU natural (8102) AKROMID® A3 GF 33 8 HU natural (8128) AKROMID® A3 GF 35 8 HU natural (8121) AKROMID® A3 GF 40 8 HU natural (8122) AKROMID® A3 GF 43 8 HU natural (8130) AKROMID® A3 GF 45 8 HU natural (8123) AKROMID® A3 GF 50 8 HU natural (8124) AKROMID® A3 GF 55 8 HU natural (8125) AKROMID® A3 GF 60 8 HU natural (8126) AKROMID® A3 GF 25 8 HU black (8118) AKROMID® A3 GF 30 8 HU black (8112) AKROMID® A3 GF 33 8 HU black (8129) AKROMID® A3 GF 35 8 HU black (8113) AKROMID® A3 GF 40 8 HU black (8114) AKROMID® A3 GF 43 8 HU black (8131) AKROMID® A3 GF 45 8 HU black (8115) AKROMID® A3 GF 50 8 HU black (8116) AKROMID® A3 GF 55 8 HU black (8119) AKROMID® A3 GF 60 8 HU black (8117) Natural (appears white) and black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'VICTREX' injection moulded PEEK thermoplastic materials. For use with water up to 85°C. VICTREX PEEK 450GL30, 450G, 450FE20 (natural – appears beige coloured), 450FC30, 450CA30 & 90GL30BLK-EU (black coloured). VICTREX FG™100, FG™120, FG™200, FG™220, FG™300 & FG™ 325 (natural – appears beige coloured). VICTREX FG™101, FG™121, FG™140, FG™201, FG™221, FG™240, FG™301 & FG™320 (black coloured). VICTREX FG™340 (dark grey coloured).
'DIC. PPS FZ-2140 BLACK'. 'DIC.PPS FZ-2140 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials. For use with water up to 85°C.
'TEC S147 R.-45 ROSSO'. Orange coloured, injection moulded, silicone rubber 'O' rings & gaskets. Shore hardness 45. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'114-9100'. Off-white coloured, PTFE paste intended for use as a thread sealant. For use with water up to 23°C.
'Loctite EA 9480'. Site applied, two-component, white coloured (once mixed) epoxy adhesive. Mix and apply as per manufacturer's technical data sheet dated October 2014. Cure for 7 days@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (either stainless steel or brass bodies in a variety of finishes). Flow is controlled via two solenoid valves (housed in a control box) activated via an infra-red sensor, the inlets to the control box incorporate stainless steel strainers. The temperature is controlled independently via a ceramic cartridge with a dome type operating member. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of wall mounted, single hole, single outlet (fixed) electronically controlled tap assemblies comprising of a concealed brass body and a separate spout and trim set (chromium plated brass). Flow is controlled by a solenoid valve activated via an infra-red sensor. The inlets (within the) concealed body incorporate a plastic filter and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Deck mounted, single hole, single outlet (fixed) electronically controlled tap assembly (various finishes). The flow is controlled by a solenoid valve activated via an infra-red sensor. The spout outlet incorporates a plastic aerator. Product supplied with metal backnuts. Maximum working pressure 6.0 bar. Maximum operating temperature 40°C.
Page 6 of 67
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
