'Iupital F10-02 nat, Iupital F20-03 nat & Iupital FG2025 nat (white coloured). Iupital F10-02 E9000 black & Iupital F20-03 E9001 black (black coloured)'. Injection moulded acetal materials, (manufactured in Bangkok, Thailand). For use with water up to 85°C.
'HF380-F'. White coloured, injection moulded ABS material. For use with water up to 85°C.
'A8401700'. White coloured, compression moulded Ceramic Alumina Al960 sealing ring. For use with water up to 85°C.
'Rocar S2'. Grey coloured, sintered & pressed silicon carbide 'faucet disc' component. For use with water up to 85°C.
'Conpipe Portland Cement Mortar NEN-EN 197-1 CEM II / A-LL 32,5 R'. Factory applied, grey coloured cementitious mortar lining. Mix cement and sand in a 1:1.1 mass ratio. Add water to cement in a mass ratio of 0.3-0.4. Cure for 28 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Conpipe Portland Cement Mortar NEN-EN 197-1 CEM I 42,5 N'. Factory applied, grey coloured cementitious mortar lining. Mix cement and sand in a 1:1.1 mass ratio. Add water to cement in a mass ratio of 0.3-0.4. Cure for 28 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JH C01'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'V7.2' issued January 2018. Cure for 15 minutes@200°C. For use with water up to 85°C.
'Polyglass VEF'. Factory applied, cream coloured, vinyl ester coating. Apply as per manufacturer's instructions '2/23 A' last reviewed July 2020. Cure for 7 days@21°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Excellube G300'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's instructions 'revision No:1' dated 15/10/2020. Cure for 20 minutes@240°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS1545A Enamel Coating'. Factory applied, blue coloured enamel coating. Apply as per document reference 'WRAS-sample-0001' dated 29.10.2020. Cure for 19 minutes (14 minutes in burner zone) @860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PAKMEL EP#3500 Series'. Factory applied, grey coloured epoxy coating. Apply as per manufacturer's instructions dated 2020.11.27. Cure for 3 minutes@230°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Sagar Sulphate Resisting cement'. Factory applied, grey coloured sulphate resisting cement. Mix cement, sand and water in a mass ratio of 1:1.50:0.50. Cure for 4 hours@28°C. Then 4 hours@45°C. Then 6 hours@40°C (humidity greater than 85%). Then 666 hours@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Krystaline Add1'. Site applied, white coloured (opaque) waterproofing admixture in the form of a powder. Admixture to be added to cement in a dosing ratio of 1kg/m³. Wet cure for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TECSIT K1'. Site applied, white coloured (opaque) waterproofing admixture in the form of a powder. Admixture to be added to cement in a dosing ratio of 1kg/m³. Wet cure for 48 hours@5°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Novus N49 Graftec`. NBR/fibre material which is dark grey on one side and black on the other. For use with water up to 23°C. For use only as a jointing/gasket material having been tested at a reduced surface area to volume ratio.
'FTC GRP Panel'. Grey (opaque) coloured, compression moulded GRP panel. For use with water up to 50°C.
'GRP-FPI-KSA Fiberstrong'. Pale green coloured (opaque) GRP pipe manufactured by filament winding. Between September 2020 and April 2024 the pipe was for use with water up to 50°C. From May 2024, the pipe is for use with water up to 60°C.
'SH Special Seal grease'. Opaque, white coloured silicone grease. Apply as per manufacturer's instructions. No cure required. For use with water up to 65°C.
'Greasil 4000'. White coloured silicone grease. For use with water up to 85°C.
Page 5 of 56
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
