Range of gate valves with blue epoxy coated ductile iron bodies and EPDM wedges. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating blue epoxy coated ductile iron bodies, epdm coated ductile iron wedges, EPDM gasket and seal. The valves are operated via a non-rising spindle with a hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of gate valves with brass bodies and stems, EPDM O-rings, with non-rising spindles with hand wheel operating members. Maximum working pressure 20.0 bar. Maximum operating temperature 100°C.
Range of gate valves incorporating DZR brass bodies, spindle headwork and hand wheel operating member. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of gate valves with brass bodies, bonnets and non-rising stems, with hand wheel or lockshield operating members. Maximum working pressure: 16.0 bar. Maximum operating temperature: 85°C
Range of IVR 605 gate valve with brass bodies, PTFE or NBR packing. The valves operate via a non-rising spindle headwork with hand wheel operating members. Maximum working pressure 16.0 bar. Maximum operating temperature 23°C.
Range of resilient seated gate valves with cast iron bodies (blue epoxy coated), EPDM coated cast iron wedges and a handwheel operating member. Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Screw down stop valve with either gunmetal, stainless steel or brass bodies (see model), EPDM seals and ‘O’-rings and seal washer. 135020 prefix and 0731G0 prefix models have a drain port fitted with an EPDM ‘O’-ring. Maximum working pressure 16.0 Bar. Maximum operating temperature 85°C.
Range of motorised position pilot operated control valves with epoxy coated ductile iron bodies and stainless-steel pipework and fittings. Maximum operating pressure 16.0 bar. Maximum operating temperature 65°C.
Range of manually operated balancing valves with blue epoxy coated ductile iron bodies, incorporating EPDM ‘O’-rings and PTFE washers. Available in the following options: DN65-DN150 sizes: DZR brass sleeve. DN65-300 sizes: blue epoxy coated ductile iron sleeve. DN65-DN150 sizes: bronze disc. DN65-300 sizes: blue epoxy coated ductile iron disc. DN200-DN300 sizes: Stainless steel (SUS304) disc. DN200-DN300 sizes: Stainless steel (SUS304) stem. DN65-DN300 sizes: Stainless steel (SUS420) stem. DN65-DN150 sizes: brass stem. The product incorporates a test port on each flange and are adjusted using a handwheel. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Electrolytic scale reducer, with a chromium plated copper body and zinc alloy anodes, for use with copper pipe (manufactured to BS EN1057) Maximum working pressure 10.0 bar. Cold water use only.
Range of electrolytic scale reducers, with a chromium plated copper body and zinc alloy anodes. Maximum working pressure 5.0 bar. Cold water use only.
Range of ultraviolet disinfection units with stainless-steel bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 40°C.
'Wanan brand WA F 501'. Factory applied, blue coloured epoxy powder coating. Apply as per 'Wanan Industry Group Co., Ltd.' TDS 'WATDS20200801a' dated 'Aug. 1, 2020'. Cure for 20 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E0-850-5210-001'. Factory applied, blue coloured epoxy powder coating. Apply as per 'Ziac Trattamenti Metallici SNC' instructions 'nr.01, rev.00, issue 01' dated 01/082016. Cure for 30 minutes@210°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 520B'. Factory applied, dark grey coloured enamel coating. Apply as per manufacturer's instructions 'ref. PRO PR 15 Gi 01 UK' dated April 04, 2024. Cure for 10 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sikadur-Combiflex® SG System’ comprising of ‘Sikadur® 31 DW’ epoxy adhesive to be used in conjunction with ‘Sika Combiflex® SG Membrane’. ‘Sikadur® 31 DW’ is a site applied, grey coloured, two-part epoxy adhesive consisting of Part A (white coloured) and Part B (black coloured). Part A and Part B are mixed in a weight ratio of 3:1, applied and cured for 14 days@30°C. ‘Sika Combiflex® SG Membrane’ is a modified flexible Polyolefin (FPO) waterproofing tape to be applied over the adhesive and is approved as the water contact layer. Apply as per ‘Sikadur-Combiflex® SG System’ System Product Data Sheet, ‘Edition: 24/10/2012, Identification no: 02 07 03 02 System, Version: GCC’. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Therma-Light Touch Up Paint'. Site applied, black coloured coating. Apply as per manufacturer's TDS 'TDS/CLP-L 44', dated '28/2/2024'. Cure for 7 days@22°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Corroless ACO Brush Grades RAL5005 (GB861) and Light Green (GB206)’ (formerly known as 'Acothane Brush Grades Blue & Green'). Site applied, blue or green coloured, two-part polyurethane coatings consisting of an amber coloured, liquid activator and blue or green coloured coating. Mix brush grade and activator in a 3.24:1 weight ratio. Apply as per technical data sheet dated Feb 2020. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika Monotop 1010’ primer for use with ‘Sika Monotop 4012’ cement mortar. Site applied, grey coloured cementitious, polymer modified coating material used as bonding primer and cementitious, fibre reinforced, low shrinkage repair mortar. First coat: Mix 25kg ‘Sika Monotop 1010’ with 5.25 litres of water and apply as per manufacturer’s ‘Sika Monotop 4012' IFU issue no. ‘001’ dated ‘July 2022’. Second coat: Mix 25kg ‘Sika Monotop 4012’ with 3.8 litres of water and apply immediately to the first coat as per manufacturer’s IFU issue no. ‘001’ dated ‘July 2022’. Cure for 21 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 369 of 583
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
