“<A> Press Copper M Profile” series press fittings with a copper body and EPDM ‘O’-rings, for use with copper pipe manufactured to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

250102006

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm - 54mm.

Marking:

A (manufacturers logo) and size on body.

Installation Requirements:

R001

Expiry date:

31/01/2030

Model:

<A> Press Copper M Profile series: 90° Street Bend: APWG5001 150000, APWG5001 180000, APWG5001 220000, APWG5001 280000, APWG5001 350000, APWG5001 420000, APWG5001 540000. 90° Bend: APWG5002 150000, APWG5002 180000, APWG5002 220000, APWG5002 280000, APWG5002 350000, APWG5002 420000, APWG5002 540000. 45° Obtuse Street Elbow: APWG5041 150000, APWG5041 180000, APWG5041 220000, APWG5041 280000, APWG5041 350000, APWG5041 420000, APWG5041 540000. 45° Obtuse Elbow: APWG5040 150000, APWG5040 180000, APWG5040 220000, APWG5040 280000, APWG5040 350000, APWG5040 420000, APWG5040 540000. Crossover Short: APWG5086 150000, APWG5086 180000, APWG5086 220000. 60 deg Copper bend with plain ends: APWG5360 280000, APWG5360 350000, APWG5360 420000, APWG5360 540000. 30 deg Copper bend with plain ends: APWG5330 280000, APWG5330 350000, APWG5330 420000, APWG5330 540000. 15 deg Copper bend with plain ends: APWG5315 280000, APWG5315 350000, APWG5315 420000, APWG5315 540000. 45 deg Copper bend with plain ends: APWG5345 280000, APWG5345 350000, APWG5345 420000, APWG5345 540000. Equal Tee: APWG5130 151515, APWG5130 181818, APWG5130 222222, APWG5130 282828, APWG5130 353535, APWG5130 424242, APWG5130 545454. Reduced Tee: APWG5130 152215, APWG5130 181515, APWG5130 181518, APWG5130 181815, APWG5130 281528, APWG5130 221222, APWG5130 181218, APWG5130 221515, APWG5130 221522, APWG5130 221822, APWG5130 222215, APWG5130 281828, APWG5130 282228, APWG5130 351535, APWG5130 352235, APWG5130 352835, APWG5130 421542, APWG5130 422242, APWG5130 422842, APWG5130 423542, APWG5130 542254, APWG5130 542854, APWG5130 543554, APWG5130 544254. Pipe Cross: APWG5901 181500, APWG5901 221500, APWG5901 281500. Fitting Reducer: APWG5243 181500, APWG5243 221500, APWG5243 221800, APWG5243 281500, APWG5243 281800, APWG5243 282200, APWG5243 352200, APWG5243 352800, APWG5243 422200, APWG5243 422800, APWG5243 423500, APWG5243 542800, APWG5243 543500, APWG5243 544200. Straight Coupler: APWG5270 150000, APWG5270 180000, APWG5270 220000, APWG5270 280000, APWG5270 350000, APWG5270 420000, APWG5270 540000. Reduced Coupler: APWG5240 221500. Cap: APWG5301 150000, APWG5301 180000, APWG5301 220000, APWG5301 280000, APWG5301 350000, APWG5301 420000, APWG5301 540000. Slip Coupler: APWG5270S150000, APWG5270S180000, APWG5270S220000, APWG5270S280000, APWG5270S350000, APWG5270S420000, APWG5270S540000.

Approval Holder:

Conex Universal Limited

Company Name

Conex Universal Limited

Address

Unit 95, Vantage Point Kingswinford

Postcode

DY6 7FT

Country

United Kingdom

Phone

+44 (0)121 5772831

General Email

Christopher.Harte@IBPGroup.com

View All Listings by this Company

Press-Inox range of stainless-steel crimped fittings (‘M’ crimp profile) for use with stainless steel pipe (manufactured to EN10204). For above ground use only. Maximum working pressure: 16Bar. Maximum operating temperature: 100°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

241102057

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

15mm - 168.3mm (excluding 28mm). (Including 28mm from December 2024).

Marking:

PCC Logo, PI 316L, Size, Year of manufacture (YY-MM) and DVGW on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

All Models sizes are in mm are Pressfit unless specified are BSP 12000 Straight Coupling 15mm - 168,3mm 12010 Straight Male Adapter 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 66.7 x 2 1/2" 76.1 x 2 1/2" 88.9 x 3" 108 x 4" 12020 Straight Female Adapter 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 12040 Sleeve Coupling 15mm – 108mm 12070 Tap Connector 15 x 3/4" 18 x 3/4" 22 x 1" 35 x 1 1/2"12080 Male Union 15 x 1/2" 18 x 1/2" 22 x 3/4" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 12100 Equal Tee 15mm - 168,3mm 12110 Reduced Tee 15mm - 168,3mm 12120 Female Tee 15mm – 108mm 12200 Bend 90° 15mm - 168,3mm 12210 Streetbend 90° 15mm - 168,3mm 12230 Bend 45° 15mm - 168,3mm 12240 Streetbend 45° 15mm - 168,3mm 1231 Male Threaded Bend 90° 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 1232 Female Threaded Bend 90° 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 1234 Female Wallplate 15 x 1/2" 15 x 3/4" 18 x 1/2" 18 x 3/4" 22 x 1/2" 22 x 3/4" 22 x 1" 35 x 1" 35 x 1 1/4" 42 x 1 1/2" 54 x 2" 12350 Male Bend 90° 15mm – 54mm 12360 Crossover / By-Pass Bend 15mm – 54mm 12400 Flange PN16 with pressend 22 x 1/2" 22 x 3/4" 22 x DN20 35 x DN32 42 x DN40 54 x DN50 66.7 x DN65 76.1 x DN65 76.1 x DN80 88.9 x DN80 108 x DN100 139.7 x DN125 168.3 x DN150 12410 Endcap 15mm – 108mm 12430 Male reducer 15mm - 168,3mm 12450 Insert Male Adapter 15mm – 54mm 12460 Insert Female Adapter 15mm – 54mm 12820 O-Ring 15mm - 168,3mm Models Added December 2024: 12010 Straight Male Adapter 28 x 3/4" 28 x 1" 12020 Straight Female Adapter 28 x 3/4" 28 x 1" 12070 Tap Connector 28 x 1 1/4" Male Union 28 x 1" 1231 Male Threaded Bend 90° 28 x 3/4" 28 x 1" 1232 Female Threaded Bend 90° 28 x 3/4" 28 x 1" 1234 Female Wallplate 28 x 3/4" 28 x 1" 12400 Flange PN16 with pressend 28 x 1" 28 x DN25

Product Images

Approval Holder:

PCC GmbH

Company Name

PCC GmbH

Address

Dusseldorfer Strasse 15, D-71332 Wailblingen

Country

Germany

View All Listings by this Company

Range of brass (CW617 or CW511L) press fit fittings (M-Type) for use with copper pipe manufactured to EN 1057. Maximum working pressure: 16 Bar. Maximum operating temperature: 99°C.

Section:

1180 Fittings for use with Tube and Pipe

Section Subtitle:

Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use

WRAS Approval Number:

241202010

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See Models below

Marking:

Ningbo Jintian (JT) Logo, Size and WRAS on body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

BP5240F Coupler: 15mm – 54mm x 1/2" BSP – 2” BSP (F). BP5243M Coupler: 12mm – 54mm x 3/8" BSP – 2” BSP (M). BP5090F Elbow: 12mm – 54mm x 3/8" BSP – 2” BSP (F). BP5092F Elbow: 12mm – 54mm x 3/8" BSP – 2” BSP (M). BP5094F Wallplate elbow: 15mm – 28mm x 1/2" BSP – 1” BSP (F). BP5130F Branch Tee: 15mm – 54mm x 15mm – 54mm x 3/8" BSP – 2” BSP (F). BP5240G Straight swivel: 15mm – 28mm x 1/2" BSP – 1 1/4” BSP (F). BP9201M Male union coupler: 12mm – 54mm x 3/8" BSP – 2” BSP (M). BP9202F Male union with Female end: 12mm – 54mm x 3/8" BSP – 2” BSP (F). BP9203PP Coupler: 12mm – 54mm. BPA9270F Female nipple: 12mm – 35mm. BPA9272M Male Nipple: 12mm – 54mm.

Product Images

Approval Holder:

Ningbo Jintian Copper Tube Co Ltd

Company Name

Ningbo Jintian Copper Tube Co Ltd

Address

No.1 ChengXi West Road, CiCheng, NingBo

Country

China

Phone

0086 574 8757 4425

General Email

audrey@jtcorp.com.cn

View All Listings by this Company

Range of copper brazed, stainless steel heat exchangers. Available with between 4 – 70 plates (see models). Maximum working pressure: 16.0 bar. Maximum operating temperature: 99°C.

Section:

1350 Heat Exchangers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

see models

Marking:

SWEO and product info on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

E5T Number of plates minimum: 6 Number of plates maximum: 48 No connection type or ¾” BSP (M) E5AS Number of plates minimum: 4 Number of plates maximum: 40 No connection type or ¾” BSP (M) E5K Number of plates minimum: 8 Number of plates maximum: 40 No connection E6T Number of plates minimum: 4 Number of plates maximum: 40 No connection type, ½” or ¾” BSP (M) E8T Number of plates minimum: 4 Number of plates maximum: 40 No connection type, ½” or ¾” BSP (M) E8AS Number of plates minimum: 4 Number of plates maximum: 46 No connection type or ¾” BSP (M) E8LAS Number of plates minimum 10 Number of plates maximum: 70 No connection, ¾” or 1” BSP (M)

Product Images

Approval Holder:

SWEP International AB

Company Name

SWEP International AB

Address

Järvgatan 3B, Box 105, 26122 Landskrona

Country

Sweden

View All Listings by this Company

Range of near boiling hot water dispensers with stainless steel tanks and flow is controlled via float switch. Maximum working pressure 3 Bar. Maximum operating temperature 98°C.

Section:

1380 Heaters

Section Subtitle:

Electric, thermal storage, mains fed, closed outlet. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within with system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241202710

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

3/8” BSP M inlet/outlet

Marking:

New Lanbiao logo on label on front of body. Model and product info on label on rear of body.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

51023, 51006, 51022-H, 51005-H, 51022-B, 51005-B

Product Images

Approval Holder:

Taizhou New Lanbiao Intelligent Technology Co.,Ltd

Company Name

Taizhou New Lanbiao Intelligent Technology Co.,Ltd

Address

JIAOXI INDUSTRIAL ZONE, QINGGANG, YUHUAN, TAIZHOU

Country

China

View All Listings by this Company

Range of indirect heat interface units (HIU) providing heating and instantaneous hot water. The central heating and hot water is generated via plate heat exchangers. Maximum operating pressure 10 bar (primary and DHW secondary). Maximum operating pressure 2.5 bar CH secondary Maximum operating temperature 90°C

Section:

1465 Heaters

Section Subtitle:

Combination boilers and Water Jacketed Tube heaters. Low volume water content. Heat retained in water heaters will cause expansion of water after closure of draw-off taps and valves. Provision for expansion of water must be made to accommodate excess pressure within the system. Particular care is required where check valves are positioned, or loose jumper valves are thought to be upstream of the heater.

WRAS Approval Number:

241104709

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

22mm compression

Marking:

Bosch on front panel and technical info on adhesive label.

Installation Requirements:

R001 R140 R360

Expiry date:

30/11/2029

Model:

7-735-600-739 - Flow 8500 40, 7-735-600-740 - Flow 8500 40 H, 7-735-600-741 - Flow 8500 50, 7-735-600-742 - Flow 8500 50 H, 7-735-600-743 - Flow 8500 60, 7-735-600-744 - Flow 8500 60 H.

Product Images

Approval Holder:

Bosch Thermotechnology Ltd.

Company Name

Bosch Thermotechnology Ltd.

Address

Danesmoor Works Pilsley Clay Cross Chesterfield Derbyshire

Postcode

S45 9BY

View All Listings by this Company

Range of water meters with epoxy coated cast iron bodies. Maximum working pressure 16.0 bar. Cold water use only.

Section:

1505 Water Meters

Size:

2½” BSP (M) connection. DN40, DN50, DN65, DN80, DN100, DN125, DN150, DN200, DN250, DN300 flanged connections.

Marking:

Resideo & Technical information on face. Size and flow arrow on body.

Installation Requirements:

R001

Expiry date:

31/10/2028

Model:

EW1710AC5000 EW1710AC5600 EW1710AC6500 EW1710AC7300 EW1710AC8100 EW1710AC8500 EW1710AC8900 EW1710AC9100 EW1710AC9200

Approval Holder:

Pittway Sarl

Company Name

Pittway Sarl

Address

A3 - ZA La Pièce 6 1180 Rolle

Country

Switzerland

View All Listings by this Company

Range of plastic pressure sensors. Maximum working pressure: 15.99 Bar. Maximum operating temperature 90.0°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See model

Marking:

Part number, data code (X = last digit of year & YYY = day of year) and Sensata on body.

Installation Requirements:

R001

Expiry date:

30/11/2029

Model:

126CP3 - ¼” BSP M, 126CP4 - 3/8” BSP M, 126CP6 - 12mm OD.

Product Images

Manufacturer:

Sensata Technologies de Mexico S de RL de CV

Company Name

Sensata Technologies de Mexico S de RL de CV

Address

Av. Aguascalientes Sur #401 Ex-Ejido Ojo Caliente Aguascalientes

Postcode

20290

Country

Mexico

Phone

+52 449 910 5500

View All Listings by this Company

Range of pressure transducers with stainless steel bodies. Maximum working pressure 10.0 Bar, 20 Bar or 40 Bar. Maximum operating temperature 99°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

9mm spigot for insertion into a quick release coupling or 1/4" BSP male.

Marking:

ABB, WRAS, Part number, Pressure range and technical info on adhesive label.

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

3KXF004496U0100 - 9mm spigot. 10 bar, 3KXF004496U0200 - 9mm spigot. 10 bar, 3KXF004496U0500 - 9mm spigot. 20 bar, 3KXF004496U0600 - 9mm spigot. 20 bar, 3KXF004496U0700 - 1/4" BSP male. 40 bar, 3KXF004496U0800 - 1/4" BSP male. 40 bar, 3KXF004496U0900 - 9mm spigot. 20 bar.

Product Images

Approval Holder:

ABB Ltd.

Company Name

ABB Ltd.

Address

Oldends Lane, Stonehouse, Glos.

Postcode

GL10 3TA

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (AMS models), 4.0 bar (EDH & EMH models) 8.0 bar (LVS models). Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102712

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

LEO on cover. LEO, model & technical information on date label on body.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

EDH (m)XX-XX-F-E 1.m: different phase. --m: single phase, none: three phase. 2.XX: Rated flow (m³/h, range:2~20 m³/h. 3.XX: Impeller progression x10, progression range:1~6. 4.F: F type motor 5.E：E type end connection mode and size -- Rated flow (2 m³/h) :G1"XG1" -- Rated flow (4 m³/h) :G1¼"XG1¼" -- Rated flow (10-20 m³/h) :G2"XG2" AMS(m)XXX-XX-E 1.m: different phase. --m: single phase，none: three phase 2.XXX: Rated flow（L/min） 3. XX: Rated power（kW）. 4.E：E type end connection mode and size -- Rated flow(70-120m³/h) : G1¼"XG1" -- Rated flow(210m³/h) :G1½"XG1¼" -- Rated flow (370 m³/h): G2"XG1¼" LVSXXX-XX-(1/2/C/D/2C/2D/C-D) -(B) -E 1.XXX: Rated flow（m³/h）, Range:1~200 m³/h. 2.XX: Impeller progession，progession range:1~36. 3. 1/2/C/D/2C/2D/C-D: Extra impeller: --1or2，On behalf of the product with 1 or 2 small size impeller. --C or D，On behalf of the product with a size C or size D impeller. --2C or 2D，On behalf of the product with two size C or size D impellers. --C-D, On behalf of the product with a size C and a size D impeller. 4.B: the materials of wetted parts --B，material is SUS 316. --None，material is SUS 304. 5.E：E type end connection mode and size -- Rated flow(1-3m³/h) : DIN Flange connection DN 25 -- Rated flow(4-5m³/h) : DIN Flange connection DN 32 -- Rated flow(10m³/h) : DIN Flange connection DN 40 -- Rated flow(15-20m³/h) : DIN Flange connection DN 50 -- Rated flow(32m³/h) : DIN Flange connection DN 65 -- Rated flow(45m³/h) : DIN Flange connection DN 80 -- Rated flow(64-90m³/h) : DIN Flange connection DN 100 -- Rated flow(120-150m³/h) : DIN Flange connection DN 125 -- Rated flow(200m³/h) : DIN Flange connection DN 150 EMH (m)XX-XX\XX-SE 1.m: different phase. --m: single phase，none: three phase. 2.XX: Rated flow（m³/h），range: 2、3、4、8、10、12、16、20m³/h. 3.XX: impeller progession (1,2,3,4,5,6,7) 4.XX: Small Impeller（1,2,3,4,5, ） 5.SE: SE Intelligent Type End connection mode and size Rated flow (2、3m³ /h) :G1"XG1" Rated flow (4m³ /h) :G1¼"XG1" Rated flow (8、10、12m³ /h) :G1½"XG1½" Rated flow (16、20m³ /h) :G2"XG2"

Product Images

Manufacturer:

Leo Group Pump(Zhejiang) Co., Ltd

Company Name

Leo Group Pump(Zhejiang) Co., Ltd

Address

No 1,3rd street, East Industry Center,Wenling, Zhejiang, China

View All Listings by this Company