Range of spherical valves with DZR brass bodies, chromium plated brass balls and PTFE seats with lever, lockshield or T-type operating members. Maximum working pressures: 22mm – 28mm = 32.0 bar and 42mm – 54mm = 25.0 bar. Maximum operating temperature 85°C.
Range of gate valves incorporating brass bodies, NBR, PTFE and fibre seals. For use with copper pipe (EN 1057) Maximum working pressure 16.0 bar. Maximum working temperature 85°C.
Range of stop valves with brass bodies and an EPDM washer. 15mm and 22mm for use with half-hard copper pipe of R250 acc. to EN1057. 20mm and 25mm for use with half hard copper pipe of R250 acc. to BS2871-2. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Screw down stop valve incorporating brass body and EPDM ‘O’-rings and hexagonal key operating member. Maximum working pressure 10.0 bar. Cold water use only.
Range of double regulating valves incorporating bronze bodies, brass disc face (½” - ¾” models) or PTFE (1” - 2” models), PTFE plate and NBR ‘O’-rings. Maximum working pressure 25.0 bar. Maximum operating temperature 100°C.
Range of polyphosphate scale inhibitors comprising of an inline (nickel plated) brass body and head, and a separate cartridge with an aluminium body and plastic cap. Maximum working pressure 5.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
'Cage Overmould 214867'. Black coloured, injection moulded ABS component. For use with water up to 70°C.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flogul® 645 Vert 6013'. Factory applied, green coloured paint. Apply as per manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PAM-MORTAR.D2'. Grey coloured (once mixed), factory applied Blast Furnace Slag Cement Mortar and admixture. Mix cement, sand, water & admixture in a mass ratio of 1:1.25:0.38:0.0008. Apply as per manufacturer’s technical data sheet dated 18/03/2021 (3rd revision) and cure for 48 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SF4300'. Nitrile rubber/aramid fibre, calendered material which is white coloured on one side and green coloured on the other side. For use with water up to 23°C.
'Norsodyne H 13212 TAE Laminate' for use with 'Polycor White Gel Coat'. ‘NORSODYNE H 13212 BTAE Laminate' was added to the approval in July 2024. The glass fibre panel is manufactured by hand lay method and then factory applied, unsaturated resin gel coat is applied by brush (BR) or spray (PA). The brush gel coat is to be applied as per manufacturer's TDS ‘4100’ dated 10.10.17 and cured for 24 hours@25°C. The spray gel coat is to be applied as per manufacturer's TDS ‘4200’ dated 10.10.17 and cured for 24 hours@25°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Aropol M 105 TA WRAS’ (formerly known as ‘Aropol M 105 TA’) & ‘Enguard GE NTRL HH WRAS’ (formerly known as ‘Enguard GE NTRL HH'): Translucent straw coloured (glossy one side textured the other), polyester laminating resin manufactured by hand lay-up & gelcoat (brush applied), sheet material. ‘Aropol M 105 TAXR’ & ‘Enguard GE WHI S WRAS’ (formerly known as ‘Enguard GE WHI S’): White coloured (glossy) on one side, translucent straw coloured (textured on the other), polyester laminating resin manufactured by hand lay-up & gelcoat (spray applied), sheet material. Apply as per Ineos Composites method statement ‘Preparation of laminated products for freshwater applications (WRAS)’, ‘code R071, edition 2’ dated 19.1.22. Cure for 9 hours at 23°C with 2% of MEKP-50 catalyst, post-cure for 24 hours@50°C and wash part thoroughly in water before use. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Ultramid® B3EG7 black 00564' (Black coloured) & 'Ultramid® B3EG7 uncolored' (appears beige). Injection moulded nylon materials. 'Ultramid® B3EG7 uncolored' is for use with water up to 65°C. 'Ultramid® B3EG7 black 00564' is for use with water up to 85°C.
'ForTii® WX11-FC BK00001, ForTii® PA Xgea21 BK28048 & PA Xgea21 BK28048'. 'ForTii® WX12-FC BK00001' was added to the approval in August 2023. Black coloured, injection moulded Polyamide materials. For use with water up to 85°C.
'Retiflex PE-Xb'. Translucent, white coloured, extruded, single-layered PE-Xb tubing. ‘RETIFLEX PEXb black’ was added to the approval in October 2024. Black coloured, extruded, single-layered PE-Xb tubing. Both tubes are for use with water up to 85°C.
Page 31 of 326
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
