'Vinoleo 77/14'. Amber coloured, soap based lubricant. Apply as per manufacturer's instructions. For use with water up to 23°C.
'PPELXS314G20NA'. Beige coloured, injection moulded PPE material. For use with water up to 85°C.
'DIC.PPS FZ-2140-F3 BLACK'. 'DIC.PPS FZ-2140-F3 BLACK-U' was added to the approval in September 2023. Black coloured, injection moulded PPS materials manufactured in Vienna, Austria. For use with water up to 85°C.
'UW61424 & UW61427 – Instinct'. White coloured, extruded PTFE tapes. For use with water up to 85°C.
'7EP2114 'O'-rings'. Black coloured, injection moulded EPDM 'O'-rings. Shore hardness 70. Tested in-radius size 0.9mm. For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Range of single hole, single outlet (fixed) combination tap assemblies (chrome plated – brass bodies). Flow is controlled via a solenoid which is actuated via an infrared sensor and the temperature is controlled by a manual lever. The spout outlets incorporate plastic aerators. The inlet hoses incorporate stainless steel strainers and an approved check valve cartridge; however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 60°C
Range of check valve cartridges with plastic bodies to be inserted into specifically dimensioned bodies. Maximum working pressure 8.6 bar. Maximum operating temperature 60°C
Non-metallic materials and components comply with BS6920 at 60°C
Range of plastic aerators. Aerators which include ‘gpm max’ in the model name, incorporate a plastic flow regulator. Maximum operating temperature 60°C
Range of aerator kits incorporating plastic flow regulators (1.9l/min, 3.5l/min & 5.0l/min) with plastic bodies and EPDM ‘O’ rings. Plastic adaptors, NBR washers and chromium plated brass housings may also be supplied as part of the kit. Maximum operating temperature 65°C.
Range of quarter turn ceramic disc headworks with brass bodies and NBR ‘O’ rings, for insertion into specifically dimensioned bores. Maximum working pressure 10.0 Bar Maximum operating temperature 85.0°C
Non-metallic materials and components comply with BS6920 at 85°C
Range of ceramic cartridge headworks with plastic bodies and EPDM ‘O’-rings for insertion into specifically dimensioned bores. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) pillar tap with brass bodies (chrome plated), incorporating ceramic disc headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (fixed) combination tap assemblies (brass bodies, various finishes - see model), incorporating either a ceramic cartridge headwork or ceramic disc headworks with various operating members (see model). The spout outlet of some models incorporates a plastic aerator (specific models only - see model). Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, fixed combination tap assemblies, (brass bodies – various finishes). Incorporating ceramic cartridge headworks with single lever operating members. The spout outlet incorporates plastic aerators. Models (23.790.xx1, 32.109.xx1 and 32.114.xx1) are supplied with lever operated pop-up wastes. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Range of single hole, single outlet (fixed) combination tap assemblies with brass bodies (black or chrome plated), incorporating ceramic cartridge headwork and single lever operating member. Spout outlet incorporates a plastic aerator. Maximum working pressure 5- 10.0 bar (see models). Maximum operating temperature 60°C – 85°C (see models).
Range of single hole, single outlet (swivel) combination tap assembly with brass body (various finishes). Incorporating either a ceramic cartridge headwork or ¼ turn ceramic disc (see models) with either single lever, dome type or cross top operating members (see models). The spout outlet incorporates a plastic aerator (excluding model F6136). Maximum working pressure - 10 Bar. Maximum operating temperature - 65 °C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, single outlet, swivel combination tap assemblies (brass bodies, various finishes - see model), incorporating a ceramic cartridge headwork with a single lever operating member. The vented models are supplied with a stainless steel braided PEX lined flexible hose assembly incorporating a ½" captive nut end connection, which provides main cold water to a venturi device which is part of a command centre (not supplied). The Arc vented models are supplied with a DZR brass tee piece, two DZR brass adaptors, two stainless-steel strainers (each combined with an EPDM washer) and a plastic flow restrictor, for installation prior to the cold inlet hose. The Arc and Cube mains models are supplied with two DZR brass adaptors and two stainless-steel strainers (each combined with an EPDM washer), for installation on each inlet hose. The spout outlet incorporates a plastic aerator. Maximum working pressure 5.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of single hole, double outlet (swivel) combination tap assemblies (chromium plated brass). incorporating quarter turn ceramic disc headworks with single lever operating members or non-rising spindle headworks and dome type or cross top operating members (see model). The spout outlet incorporates a plastic flow straightener. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Page 31 of 63
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
