'Chemfix CH+ MAX'. Site applied, two-part (supplied with internal mixing nozzle so no manual mixing required), brown coloured chemical anchor resin. Apply as per manufacturer's instructions dated 18/05/2022. Cure for 4 days@5°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ME FGL 75D'. Black coloured, ebonite material manufactured by calendaring and autoclave curing. Shore hardness 75. Tested in-radius size 1.75mm. For use with water up to 23°C.
'E24 EPDM moulded parts.' Black coloured, injection moulded EPDM seals. Shore hardness 75. Type 1 moulded seals have a tested in-radius size of 4.2mm and Type 2 moulded seals have a tested in-radius size of 0.7mm. For use with water up to 85°C.
'01/U70EP 'O' ring' with a tested in-radius size between 0.5mm & 3.5mm. In June 2024, the follow components were added to the approval: ‘01/U70EP Cylindrical Gasket’ with a tested in-radius size between 0.9mm & 1.25mm. ‘01/U70EP Membrane’ with a tested in-radius size between 2.1mm & 5.5mm. Black coloured, injection moulded EPDM components. Shore hardness 70 For use with water up to 85°C.
'01/U80EP'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 80. Tested in-radii sizes between 1.00mm & 2.5mm. For use with water up to 85°C.
'EP7/3/7 BLK O-rings & gaskets'. Black coloured, injection moulded EPDM 'O' rings and gaskets. Shore hardness 75. The gaskets have an in-radius size of 1.0mm. The 'O' rings have an in-radius size of 1.3mm. For use with water up to 85°C.
'EP70 BLK Seals'. Black coloured, injection moulded EPDM seals. Shore hardness 70. Tested in-radius size 1.0mm. In April 2024, 'EP70 BLK 'O' rings’, black coloured, injection moulded 'O' rings were added to the approval. Shore hardness 70. Tested in-radius size of 1.3mm For use with water up to 85°C.
'HH7118F 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets. Shore hardness 70. Tested in-radius size 1.5mm. For use with water up to 85°C.
'334137 – EPDM Peroxide 70'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'PT0469'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.3mm. For use with water up to 85°C.
'EP002971PWRC'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EP7001165PWRC'. Black coloured, compression moulded EPDM rubber material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'EPDM HT5697-4A'. Black coloured, injection moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. Between May 2024 and October 2024, the material was for use with water up to 50°C. Between November 2024 and May 2029, the material is for use with water up to 60°C.
'ML 57302'. Black coloured, compression moulded EPDM material. Shore hardness 55A. Tested in-radius size 1.0mm. For use with water up to 23°C.
‘LS40T-0301, LS50T-0301, LS60T-0301, LS70T-0301 & LS80T-0301’. Injection moulded, liquid silicone rubber sheet material, available in white, grey, black, blue, green, natural (unpigmented) & red colours. Shore hardness between 40SH-A & 80SH-A. Tested in-radius size 1.0mm. For use with water up to 85°C.
'kSil GP200, kSil GP250, kSil GP350, kSil GP400, kSil GP450 & kSil GP530'. Pale yellow/white coloured, extruded silicone rubber cellular sponge materials. Shore hardness between 37 & 70. Tested in-radii sizes between 1.53mm & 1.76mm. For use with water up to 85°C.
‘Paryls® PPSU F1550NC (natural grade – appears brown), F1550GY (grey coloured), F1550BK (black coloured) & F1550WH (white coloured)’. Injection moulded PPSU materials. For use with water up to 85°C.
'POKETONE’ range of natural (appears light brown), grey and black, injection moulded Polyketone materials. For use with water up to 85°C. 'M(a)3FG(b)A-NP0, M(a)3FG(b)A-GY(c), M(a)3FG(b)A-BK(c)'. (a) indicates the MI(g/min) or viscosity of its neat resin and is replaced with: 9 = 150~250, 3 = 40~80, 6 - 4~8 or 7 = 2~4. (b) indicates the content of glass fibre and is replaced numbers between 1 & 9 (9 indicating the maximum of 50%). NP0 indicates natural material, GY indicates grey material & BK indicates black material. (c) can indicate a random product number of each grade OR the ratio of carbon black and is replaced with numbers between 0 & 9.
Range of screw down stop valves with plastic bodies incorporating EPDM ‘O’-rings and seal. For use with PE-X pipe (manufactured to BS7291-3), BPB pipe (manufactured to BS7291-2) and copper pipe (manufactured to EN1057). Maximum working pressure and operating temperatures: 12.5 bar @ 20°C & 6.0 bar @ 65°C.
Bidet seat assembly which discharges via a sensor actuated solenoid valve and utilises a type `AB` airgap (verified by test - suitable for backflow protection against fluid category 5). The inlet incorporates a strainer and flow regulator. Maximum working pressure 10.0 bar. Cold water supply only.
Page 292 of 509
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
