'CORROPOXY-FGE400'. Factory applied, red coloured, two-component epoxy coating. Mix and apply as per manufacturer's Application Procedures 'CPE/ FGE-400/Procd. /02', 'issue no - 03', dated '12.05.2022'. Cure for 30 minutes@45°C. For use with water up to 45°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'AYYTCM-01'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per MSDS '20170508A1'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Luberpox – 2K – DS-Lackfarbe IV80, Wilo Grün nach Muster/IW80 Hardener (green coloured) & Luberpox – 2K – DS-Lackfarbe IV80, RAL 9011 Graphitschwarz/IW80 Hardener (black coloured). Factory applied epoxy coatings. Mix in a 5:1 weight ratio and apply as per Berger-Lacke Technical Data Sheet (rev. 41-06.11.2023). Cure for 7 days at 22°C. For use with water up to 23°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LZYX002'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:3.0:0.4 weight ratio and apply as per Instruction Sheet '201 8 07 0', revision 'A2'. Air cure for 4 hours@23°C and the steam cure for 6 hours@60°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-BFS'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14B', revision '01', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RAX Cement Mortar'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instructions 'WI-PRD-08', rev. '00', dated '01.02.2023'. Cure for 24 hours@28°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Flexseals 163 Green'. Green coloured fibre sheet material manufactured by calendaring. For use with water up to 23°C. For use only as a jointing/material having been tested at a reduced surface area to volume ratio. This material incorporates a natural ingredient. Please note that water companies will evaluate the evidence provided and may ask for more information and they reserve the right to refuse installation.
‘Pilotpack 3480, 5035, 3435, 4040, 7099, 3408, 3410 & 5020’ range of gland packings. 3480 & 3435 are dark grey coloured, graphitised PTFE based. 5035 is yellow & black coloured, graphitised PTFE/aramid based. 4040 is grey coloured, graphite based. 7099 is white coloured, acrylic/PTFE based. 3408 is white coloured, lubricated PTFE based. 3410 is white coloured, lubricated PTFE based. 5020 is light yellow coloured, lubricated aramid based. All grades are for use with water up to 85°C. For use only as gland packing material having been tested at a reduced surface area to volume ratio.
'SUPIC-710PT GRP'. Beige coloured GRP material manufactured by hand lay. For use with water up to 23°C.
'SYH-PH215'. White coloured grease. Apply as per manufacturer's instructions. For use with water up to 85°C.
'EcoPaXX Q-DWX12 BK00002'. Black coloured, injection moulded polyamide material. For use with water up to 85°C.
'Pemaron660G6W NC01'. Natural (appears off-white), injection moulded, glass-reinforced PA66 material. For use with water up to 85°C.
'AGRULINE PE100RC Pipe'. Black coloured, extruded polyethylene pipe. For use with water up to 85°C.
'TP13270 Green'. Green coloured polyethylene material manufactured by rotomoulding. For use with water up to 70°C.
‘LURANYL® KR 2402 TW 35061, LURANYL® KR 2403 G4 TW 26343 & LURANYL® KR 2403 G6 TW 26343’. Black coloured, injection moulded polyphenyleneoxide/polystyrene materials. In May 2025, ‘LURANYL® KR 2403 G2 TW GY4090-24’ & ‘LURANYL® KR 2403 G6 TW GY4040-24’, dark grey coloured, injection moulded polyphenyleneoxide/polystyrene materials were added to the approval. All grades are for use with water up to 85°C.
'Powertherm PP-R pipe'. Green coloured, extruded PP-R pipe (manufactured from SABIC Vestolen P 9421). For use with water up to 85°C.
Page 282 of 509
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
