Range of UV disinfection units with stainless steel bodies and quartz tubes. Maximum working pressure 10.0 bar. Cold water use only.
Range of ion exchange water softeners (salt regenerated) for domestic use. Maximum working pressure 6.0 bar. Cold water use only.
Smart water monitor with plastic housing, integrated motorised shut off valve, ultrasonic transducer and pressure sensor. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Non-metallic materials and components comply with BS6920 at 85°C
'DURACON® GB-25R WF3500'. Off-white coloured (translucent), injection moulded POM material. For use with water up to 85°C.
'LAC 500 MP 5038 BIANCO'. White coloured ABS material manufactured by co-extrusion. For use with water up to 23°C.
'Tufbon PTS600, PTS888 & CG100'. Black coloured, sintered, carbon graphite sealing rings. For use with water up to 85°C.
Factory applied, grey coloured blast furnace slag cements. ‘BFSC PAM MDN 1’. Mix water, sand, admixture & cement in a mass ratio of 0.33:2.35:0.0080:1 and apply as per manufacturer’s instructions ‘CE 7M’, dated ‘25/08/15’. Cure for 7 hours@70°C. For use with water up to 60°C. BFSC PAM GDN 1’. Mix water, sand, admixture & cement in a mass ratio of 0.33:2.84:0.0065:1 and apply as per manufacturer’s instructions ‘CE 8M/-3A’, dated ‘25/08/15’. Cure for 7 hours@70°C. For use with water up to 60°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'GCF-SRC'. Factory applied, grey coloured cement mortar. Mix sand, cement and water in a ratio of 4:2:1 and apply as per manufacturer's instructions 'QC-WI-8.1.8, revision 2/0, issue date 30/10/2021'. Cure for 28 days@24°C. For use with water up to 65°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Weberdry epo PW'. Site applied, light grey coloured (once mixed), two-component epoxy coating. Mix Part A (light grey coloured) with Part B (translucent, yellow coloured) in a weight ratio of 100:20. Apply as per manufacturer's TDS 'Edition: 04.23-A'. Cure for 24 hours@25°C. Mix and apply a second coat in the same way and then cure for 14 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`EcoZmart Waterproofing`. Site applied, grey coloured tanking slurry. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 1 as per manufacturer's IFU 'TCOWP001', dated '26/05/2023'. Cure for 24 hours@7°C. Mix tanking slurry with water in a 3:1 volume ratio and apply coat 2, 24 hours after the first coat, as per manufacturer's IFU IFU 'TCOWP001', dated '26/05/2023'. Cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SRC GRP Pipe'. Beige coloured (translucent), SRC GRP pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'SRC GRV Pipe'. Beige coloured (translucent), SRC GRV pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'SRC GRE Pipe'. Yellow coloured (opaque), SRC GRE pipe manufactured by dual helical filament winding. For use with water up to 70°C.
'Extrabrite'. Light brown coloured GRE pipe manufactured by filament winding (at Extra Co Fibre Glass & Prefab Houses LLC – Sharjah, UAE and Extra Co Industries LLC – Ras Al Khaimah, UAE). For use with water up to 60°C.
'Extrabrite'. Light brown coloured GRE fittings manufactured by filament winding (at Extra Co Fibre Glass & Prefab Houses LLC – Sharjah, UAE) or hand lay-up (at Extra Co Industries LLC – Ras Al Khaimah, UAE). For use with water up to 60°C.
'Al Muftah Sectional Tank Panel'. Light grey coloured, hot press moulded GRP panel. For use with water up to 23°C. From April 2024 the panel is for use with water up to 50°C.
'Pure Carbon STM-05'. Dark grey coloured, compression moulded carbon graphite ring/washer. For use with water up to 85°C.
'DM2506 Hose'. White coloured (translucent), extruded silicone rubber hose. Shore hardness 70. Tested in-radius size 2.28mm. For use with water up to 85°C.
‘RADISTRONG® AROMA RV400RKC2 106 NT, RV500RKC2 106 NT & RV600RKC2 106 NT’. ‘RADISTRONG® AROMA RV400RKC2 306 BK, RV500RKC2 306 BK & RV600RKC2 306 BK’. ‘RADISTRONG® AROMA RV300RKC2 106 NT’ & ‘RADISTRONG® AROMA RV300RKC2 306 BK’ were added to the approval in February 2024. Natural (indicated by NT - appear cream in colour) and black coloured (indicated by BK), injection moulded, glass fibre filled (between 30% & 60%), PA66 materials. For use with water up to 85°C.
'AG30E'. Black coloured, injection moulded PA66+GF30 material. For use with water up to 85°C.
Page 275 of 568
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
