‘4MID 9A22130 HW-A ABK, 4MID 9A22135 HW-A ABK, 4MID 9A22140 HW-A ABK, 4MID 9A22145 HW-A ABK & 4MID 9A22150 HW-A ABK’. Black coloured, glass-fibre reinforced PA66 materials. For use with water up to 23°C.
'Mapex® AN4920SN FWB50 & GITOP® G3A2 M01FWB'. Black coloured, injection moulded, glass fibre reinforced PA66 materials. For use with water up to 85°C.
'POLYNT 1349 TAEQ20 to be used in conjunction with POLYCOR LP PA FC CLEAR 0200'. POLYNT 1349 TAEQ20 is a polyester resin and LP PA FC CLEAR 0200 is a factory applied, gel coat (when used together the material appears light pink in colour). Apply as per manufacturer's TDS ‘7206 updated 10.10.17’. Cure for 24 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MMP PE100 Pipe'. Black coloured (with blue coloured external stripes), extruded PE100 pipes manufactured from 'Sabic P6006' or 'Borouge HE3490-LS'. For use with water up to 85°C.
'HE3490-ELS-H'. Black coloured, extruded polyethylene material. For use with water up to 60°C.
`Revolve N-525 (6056) Natural (appears white coloured) & BH3239 Black (black coloured)`. Polyethylene materials manufactured by rotational moulding. For use with water up to 85°C.
'XYRON WG732 AWY2266, WG732 AWY2269, WG732 AWY6628, WG722 AWY6627, W5002 AWY1208, W5002 AWY2267, W5002 AWY6629, W5002 AWY3326, WG722 AWY2261, WG732 AWY3325, WG722 AWY3324 & WG733 ABY3315'. Injection moulded, black, grey or beige coloured PPE materials manufactured in Thailand & China. For use with water up to 85°C.
`Superfast Copper`. Site applied, copper coloured epoxy putty. The putty should be kneaded together, its supplied in a pre-measured 1:1 mass ratio and applied as per manufacturer's directions for use dated August 9th, 2021. Cure for 24 hours@22°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EUW-70'. Black coloured, injection moulded EPDM diaphragm. Shore hardness 70. Tested in-radius size 0.95mm. For use with water up to 60°C.
'1922, 1923 & 1933 washers'. Red coloured, injection moulded silicone rubber washers. 1923 washers have an in-radius of 1.59mm. 1933 washers have an in-radius of 0.83mm. 1922 washers have an in-radius of 1.23mm. For use with water up to 85°C.
'SI-30T, SI-40T, SI-50T, SI-60T, SI-70T, SI-80T & SI-90T (transparent, unpigmented)'. 'SI-30R, SI-40R, SI-50R, SI-60R, SI-70R, SI-80R & SI-90R (red coloured)'. 'SI-30B, SI-40B, SI-50B, SI-60B, SI-70B, SI-80B & SI-90B (blue coloured)'. Range of compression moulded, silicone rubber materials. Shore hardness between 30 & 90. Tested in-radius size 0.9mm. For use with water up to 85°C.
'Hetron 922'. Dark yellow coloured, injection moulded vinylester resin. For use with water up to 45°C.
Floor mounted, single hole, single outlet (fixed) combination tap assembly (chromium plated brass), incorporating a ceramic cartridge headwork with single lever operating member and a lockable diverter to shower outlet. The spout outlet incorporates a plastic aerator. The product is supplied with a shower hose and handset. Both the shower outlet (from the main body) and the inlet to the shower handset incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of deck mounted, electronically operated combination tap assemblies (chromium plated brass). The flow is controlled by a solenoid valve which is actuated via an infrared sensor on the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Side entry BS1212-4 (2016) compact type float operated valve for WC flushing cisterns. The inlet incorporates a flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
WC flushing cistern incorporating a bottom entry BS1212-4 (2016) compact type float operated inlet valve providing a Type AG air gap with a dual flush drop valve for full flush volumes of up to 6 litres and a reduced flush of up to 3 litres. The cistern is operated by a pnuematic push button. Maximum working pressure 10.0 bar. Cold water use only.
Range of concealed WC cistern in white plastic incorporating a BS 1212-4:2016 side entry float operated inlet valve providing a Type AG air gap arrangement and a single or dual flush outlet valve. The full flush can be set at 6 litres and the reduced flush can be set at 3 litres. The inlet supply incorporates a servicing valve. Maximum operating pressure 10.0 bar. Cold water use only.
BS EN 997:2018 RAK Compact Rimless Wall Hung 700mm COMRIMWH W.C. pan (Ceramic), Thomas Dudley ‘A’ frame incorporating a Thomas Dudley Vantage Concealed cistern with a side entry compact type float operated inlet valve which discharges via a Type AG airgap and a dual flush pneumatic drop valve capable of full flush volumes of 4.5 litres and a reduced flush of 3 litres. The inlet connection hose incorporates a servicing valve. Maximum working pressure 10.0 bar. Cold water use only.
Spring loaded resilient trim, in-line check valve cartridges incorporating plastic guides and stem, NBR or EPDM seals within a plastic housing. For insertion into pipes or fittings with specifically dimensioned bores. Maximum working pressure 16.0 Bar. Maximum operating temperature 65°C.
Page 28 of 205
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
