'PANG30'. Black coloured, injection moulded, glass fibre reinforced nylon material. For use with water up to 85°C.
'ELYSEE HDPE PE 100' & 'ELYSEE HDPE PE 80' pipes. Black coloured (with blue lines), extruded PE 100 & PE 80 Pipes. For use with water up to 23°C.
'RBM PE40 potable water pipe'. Black coloured (with blue external stripes), extruded LDPE pipe. For use with water up to 23°C.
`Simona Peak Pipe Systems PE100 Pipe`. Black coloured, extruded PE100 pipes. For use with water up to 23°C.
'Supreme PE Pipe TSIL G'. Black coloured (with blue stripes), extruded PE 100 pipe. For use with water up to 60°C.
'TP12939 Natural'. Natural (appears off-white) polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'TP12978 Black'. Black coloured, polyethylene material manufactured by extrusion compounding and then rotomoulding. For use with water up to 70°C.
'LLFA® Compression Tape'. Red coloured (with white stripe), silicone based tape, manufactured by extrusion. Shore hardness 55. Tested in-radius 0.4mm. Apply as per manufacturer's instructions 'LLFA® Compression Tape User Guide Rev. 2; July 1, 2017'. For use with water up to 75°C.
'Buffalo PUR500'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '14/08/2018'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Mungo Injection System MIT800RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated 'Jun-23'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP025CTF 'O' rings and gaskets'. Black coloured, compression moulded EPDM 'O' rings and gaskets'. Shore hardness 40-90. 'O' rings have an in-radius size of between 0.5mm & 5.0mm. Gaskets have an in-radius size of between 0.5mm & 1.75mm. For use with water up to 85°C.
'Ganga 50, 60, 70, 80 & 90'. Black coloured, compression moulded EPDM materials with a shore hardness of between 50 & 90 ShA. Tested in-radius size 1.1mm. For use with water up to 85°C.
'EPDM50BKWS, EPDM55BKWS, EPDM60BKWS, EPDM65BKWS, EPDM70BKWS, EPDM75BKWS & EPDM80BKWS'. Black coloured, compression moulded EPDM rubber materials. Shore hardness between 50 & 80. Tested in-radius size 1.0mm. For use with water up to 85°C.
'JJSXEPDMIRHD50 (shore hardness 50) & JJSXEPDMIRHD70 (shore hardness 70)'. Black coloured, compression moulded EPDM materials. Tested in-radius size 0.99mm. For use with water up to 23°C.
'Water Life'. Black coloured, compression moulded NBR 'O' rings. Shore hardness 70. Tested in-radius size between 0.75mm & 1.25mm. For use with water up to 23°C.
Range of single hole, single outlet (fixed) electronically controlled tap assemblies (various finishes - see model). Flow is controlled by a solenoid valve activated by via an infra-red sensor. The IRBS5-CP models have a multi-layer PEX lined hose between the solenoid and the spout. The TK-201LT65 models have a stainless steel braided PEX lined flexible hose between the solenoid and the spout. The spout outlet incorporates a plastic aerator. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Range of single hole, single outlet, fixed, electronically controlled tap assemblies (chrome plated brass bodies). Flow is controlled via an infra-red activated solenoid valve and the spout outlets incorporate plastic aerators. The inlets incorporate a stainless-steel filter washer. Maximum working pressure 8.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of single-hole, single outlet, (fixed), electronically controlled tap assemblies (chrome plated brass or stainless steel bodies). Flow is controlled via solenoid valve activated via an infra-red sensor. The spout outlets incorporate plastic aerators. Maximum working pressure 8.0 Bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted, electronically controlled combination tap assemblies, (chrome plated brass or stainless steel bodies). The flow is controlled by a solenoid valve that is activated via an infra-red sensor The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose assembly, connecting the spout to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Range of electronically operated combination tap assemblies, (chrome plated brass bodies). The flow is controlled by a solenoid valve which is actuated via an infrared sensor. The spout outlet incorporates a plastic aerator. The product incorporates a stainless steel braided PEX lined flexible connection hose, connecting the tap to the solenoid valve. Maximum working pressure 8.0 Bar
Non-metallic materials and components comply with BS6920 at 65°C
Page 253 of 590
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
