'F1520'. Blue-grey coloured PTFE material manufactured by ram extrusion. For use with water up to 85°C.
3M™ Dyneon™ TF 1620, TF 1641, TF 1645, TF 1702, TF 1750, TFM 1600, TFM 1635, TFM 1700, TFM 1705, TF 4103K, TF 4105K, and TFM 4105K. White coloured, pressed+sintered PTFE materials. 3M™ Dyneon™ TF 2021Z, TF 2025Z, TF 2029Z, TF 2035Z, TF 2053Z, TF 2071Z, TF 2072Z, TF 2073Z, TFM 2001Z, TFM 2033Z and TFM 2070Z. White coloured, extruded PTFE materials. 3M™ Dyneon™ TF 4215 & TF 4303. Black coloured, pressed+sintered PTFE materials. For use with water up to 85°C.
'National Plastic Sharjah-LF PVC Pipe' & 'National Plastic Al Ain, Abu Dhabi-LF PVC Pipe'. Grey coloured, extruded PVC pipes. For use with water up to 60°C.
'Art. 0985077200'. Black coloured, extruded silicone rubber tape. Shore hardness 55. Tested in-radius size 0.25mm. For use with water up to 23°C.
‘DEWALT PV60-PRO’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions rev. 1, version 16/01/2023. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPDM 70.10-02 'O'-rings & gaskets'. Black coloured, injection moulded, EPDM 'O' rings and gaskets. Shore hardness 70. The 'O' rings have a tested in-radius size of 0.5mm. The gaskets have a tested in-radii size between 0.5mm & 2.6mm. ‘O’ rings with a tested in-radius size of 2.6mm were added to the approval in May 2023. For use with water up to 85°C.
‘07096-80 gaskets’. Black coloured, compression moulded EPDM gaskets. Shore hardness 80. Tested in-radius size between 0.9mm & 1.75mm. For use with water up to 85°C.
'EP2480 BLK 'O' ring'. Black coloured, injection moulded EPDM 'O' ring. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
'GM-EP01'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.15mm. For use with water up to 23°C.
'EPDM E282'. Black coloured, compression moulded EPDM sheet material. Shore hardness 80A. Tested in-radius size 1.0 For use with water up to 85°C.
'E7014F'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C. From April 2023, the material is for use with water up to 85°C.
'EPDM 70.503-00'. Black coloured, injection moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'51616 – E40, 51616 – E50, 51616 – E60, 51616 – E70 & 51616 – E80'. Black coloured, compression moulded EPDM materials. Shore hardness between 40 & 80. Tested in-radius size 1.0mm. For use with water up to 65°C.
'NBR 70.10-17 'O' rings and gaskets'. Black coloured, injection moulded NBR 'O' rings and gaskets. Shore hardness 70. Tested in-radii sizes between 0.5mm & 2.6mm. For use with water up to 23°C.
'NBR 70.10-02 'O' rings and gaskets'. Black coloured, injection moulded NBR rubber 'O' rings and gaskets. Tested in-radius size between 0.5mm & 2.6mm. Shore hardness 70. For use with water up to 23°C.
'CH C 170 DM'. Black coloured, compression moulded NBR rubber. Shore hardness 71. Tested in-radius size 1.0mm. For use with water up to 23°C.
'kSil PL60 Translucent'. Off-white coloured (translucent), silicone rubber material which is extruded onto the calendar. Shore hardness 60. Tested in-radius size 1.05mm. For use with water up to 85°C.
'Loctite SI 5331 (known as 'Loctite 5331')'. White coloured silicone thread sealant. Apply as per manufacturers technical data sheet ‘reference 1.7’ dated May 2014. Cure for 96 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘M930F, M330F, M630F, M730F, M410F & M710F’. Beige coloured, injection moulded polyketone materials. For use with water up to 85°C.
Range of wall mounted electric showers (various finishes). The product incorporates a solenoid valve controlling the flow. Maximum working pressure 10.0 bar. Maximum operating temperature 53°C. Cold supply only.
Page 248 of 567
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
