Range of below ground water meter manifolds with a plastic body and a spherical valve at the inlet. Models incorporate an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate it provides backflow protection. For use with PE80 blue pipe (manufactured to BS EN 12201). Maximum working pressure 12.5 bar. Cold water use only.

Section:

1510 Water Meter Manifolds

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

EBCO on manifold. EBCO & flow arrow on bracket.

Installation Requirements:

R001 R008

Expiry date:

28/02/2031

Model:

MB2012525BM: EBCO Raised Manifold 25mm Pushfit. MB2010303BM: EBCO Raised Manifold ¾” BSP. MB2011010BM: EBCO Raised Manifold 25mm Blue MDPE Pipe.

Approval Holder:

Atlantic Plastics Ltd.

Company Name

Atlantic Plastics Ltd.

Address

Coytraherne Close, Brackla, Bridgend

Postcode

CF31 2AX

Country

United Kingdom

Phone

01656672628

General Email

rhodgkiss@atplas.co.uk

View All Listings by this Company

Range of flow sensors incorporating either brass, plastic or stainless steel bodies & EPDM ‘O’-rings. Maximum working pressure 10.0 bar for models VVXA, VVXC, VVXB. Maximum working pressure 16.0 bar for models VVXD & VVXE. Maximum operating temperature 90°C.

Section:

1530 Miscellaneous Fittings

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Sika logo, pressure, temperature, other tech info on body; flow arrow on body.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

VVXA Vortex Flow Sensor Type VVX15 Vortex Flow Sensor nominal size 15. Body material PPS, G ¾ male or ½” NPT male VVXC Vortex Flow Sensor Type VVX20 Vortex Flow Sensor nominal size 20. Body material PPS G 1 male or ¾” NPT male or Quick-Fasten male/female VVXB Vortex Flow Sensor Type VVX25 Vortex Flow Sensor nominal size 25. Body material PPS G 1¼ male or 1” NPT male VVXD Vortex Flow Sensor Type VVX32 Vortex Flow Sensor nominal size 32. Body material brass or stainless steel G 1½ male or 1½” NPT male VVXE Vortex Flow Sensor Type VVX40 Vortex Flow Sensor nominal size 40. Body material brass or stainless steel G 2 male or 2” NPT male • digit 1,2,3: Designation of the series o VVX >>> VVX series • digit 4: nominal diameter o A >>> DN 15 for type VVX15 o C >>> DN 20 for type VVX20 o B >>> DN 25 for type VVX25 o D >>> DN 32 for type VVX32 o E >>> DN 40 for type VVX40 • digit 5,7,8,9,10,11,12,13,14,15: Device configuration • digit 6: Private label o S >>> SIKA (standard) o E >>> SIKA (standard) with ETL marking • digit 4 and 16: tube material / process connection o A and 4 >>> PPS – G 3/4 male thread o A and C >>> PPS – ½”NPT male thread o C and P >>> PPS – Quick-Fasten connection o C and 7 >>> PPS – G 1 male thread o C and 8 >>> PPS – 3/4" NPT male thread o B and 6 >>> PPS – G 1 1/4 male thread o B and E >>> PPS – 1” NPT male thread o D and U >>> Brass – G 1 1/2 male thread o D and 0 >>> Brass – 1½" NPT male thread o D and M >>> Stainless steel – G 1 1/2 male thread o D and Y >>> Stainless steel – 1½" NPT male thread o E and X >>> Brass – G 2 male thread o E and 9 >>> Brass – 2" NPT male thread o E and O >>> Stainless steel – G 2 male thread o E and Z >>> Stainless steel – 2" NPT male thread

Approval Holder:

SIKA Systemtechnik GmbH

Company Name

SIKA Systemtechnik GmbH

Address

Struthweg 7-9 Kaufungen

Postcode

34260

Country

Germany

Phone

+49 5605 803 652

General Email

grass@sika.net

View All Listings by this Company

Range of multistage and single stage water pumps with stainless steel bodies and impellers. Maximum working pressure 2.0 bar (MS(s) models), 4.0 bar (AM(E) models) Maximum operating temperature 85°C

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

241102725

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

Please refer to model.

Marking:

TERAL, model, size & technical information on date label on body. Flow arrow on cover.

Installation Requirements:

R001 R415

Expiry date:

30/11/2029

Model:

MS(m)XXX-XX-E 1.m: different phase. --m: single phase, none: three phases 2.XXX: Rated flow (L/min) 3.XX: Rated power(kW). 4.E: E type end connection mode and size -- Rated flow(70-120m3/h): G1¼"XG1" -- Rated flow(210m3/h): G1½"XG1¼" -- Rated flow (370 m3/h): G2"XG1¼ AM(E) XXxXX (B) X/X-X XX(S) 1. E: Intelligent Type 2. XX: Inlet diameter (mm), range: 25,32,40,50 mm. 3. XX: Outlet diameter (mm), range: 25,32,40,50 mm. 4. B: alternative pump group 4. X/X: number of impeller /number of smaller impeller (if any) 5. X: motor frequency 6. XX: Rated power(kW) 7. S: different phase (S: single phase, none: three phases.)

Range of multistage centrifugal pumps with stainless-steel housings, stainless-steel impellers and EPDM ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250902720

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN25 - DN200 flanged.

Marking:

Dooch, model, serial number and technical info on data plate on body.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Proviso:

The discharge from the drain core must be made via a type AA, AB or AD air gap, or in accordance with EN 1717.

Model:

XRLNa-b-c-d Where: XRL = model. With N = Wetted metallic material in SUS316L, Without N = Wetted metallic material in SUS304. a = Rated flow in m³/h (1 – 255). DN25 = 1-3. DN32 = 4-5. DN40 = 10. DN50 = 15-20. DN65 = 32. DN80 = 45. DN100 = 64 or 95. DN150 = 125-155. DN200 = 185-255. b = Number of impellers (stages 1 – 36). DN25 & DN32 models with 1 – 36 stages. DN40 models with 1 – 22 stages. DN50 models with 1 – 17 stages. DN65 models with 1 – 14 stages. DN80 models with 1 – 13 stages. DN100 models with 1 – 8 stages. DN150 models with 1 – 10 stages. DN200 models with 1 – 8 stages. c = Number of cutting impellers (0 – 3). (Note: c can be omitted when c = 0.) d = DN size (DN25 – DN200). (Note: d can be omitted.) E.g., XRL32-7-2-DN65 denotes: Pump is made of SUS304, rated flow 32 m³/h, 7 impellers, 2 cutting impellers and size DN65.

Approval Holder:

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Company Name

SHANGHAI SINO-KOREA DOOCH PUMP MFG. CO., LTD

Address

No 239 Zhangliantang Rd Liantang Ind Park Qingpu District Shanghai City China

View All Listings by this Company

Manufacturer:

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Company Name

ZHONGHAN DOOCH PUMP(HUZHOU)CO., LTD.

Address

NO 669 DAYANG ROAD KANGSHAN STREET HUZHOU ZHEJAING CHINA

View All Listings by this Company

Range of pumps, with stainless steel bodies, impellers and shaft. Maximum working pressure 10.0 bar. Cold water use only.

Section:

1610 Pumps

Section Subtitle:

Wholesome water use.

WRAS Approval Number:

250904702

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

See models.

Marking:

Wilo, made in Korea, Model No., Serial No., website address, & other tech info on data label. Wilo printed on control panel.

Installation Requirements:

R001 R415

Expiry date:

30/09/2030

Model:

PBI-L203EA - Suction 25A(1”) Discharge 25A(1”) PBI-L204EA - Suction 25A(1”) Discharge 25A(1”) PBI-L205EA - Suction 25A(1”) Discharge 25A(1”) PBI-L402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-L802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-L803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD203EA - Suction 25A(1”) Discharge 25A(1”) PBI-LD402EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD403EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD404EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD405EA - Suction 32A(1 1/4”) Discharge 25A(1”) PBI-LD802EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) PBI-LD803EA - Suction 40A(1 1/2”) Discharge 32A(1 1/4”) 1 - Series PBI-L: Electronic Boosting Pump Variable Speed Pump(Inverter Pump). 2 - Number of Pumps None/blank : Single Type (One Pump), D: Duplex Type (Two Pumps). 3 - Rated Flow capacity 2 : 2㎥/hr, 4 : 4㎥/hr, 8 : 8㎥/hr. 4 - Number of Impellers 02 : 2 Impellers, 03 : 3 Impellers, 04 : 4 Impellers, 05 : 5 Impellers. 5 - Power 60Hz L: 110V ~, J: 120V ~ , 127V~, M: 220V~ D: 110V/220V~, I: 220/380V 3~, T: 220V 3~, U: 380V 3~, N: 440V 3~, R: 480V 3~. 50Hz Z: 110V ~, C: 120V ~, 127V~, E: 220V ~, F: 110V/220V ~, G: 220/380V 3~, H: 220V 3~, Q: 380V 3~, Y: 440V 3~. 6 - Automatic mode. None/blank : non automatic models A: models which equips themselves with components that are responsible for automatic mode.

Approval Holder:

WILO Pumps Ltd.

Company Name

WILO Pumps Ltd.

Address

46, Mieumsandan 1-ro, Gangseo-gu, Busan, Republic of Korea, 46730

View All Listings by this Company

Showers handset with plastic body (chromium plated). Open outlet use only.

Non-metallic materials and components comply with BS6920 at 60°C

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

2304111

Size:

½” BSP (M).

Marking:

Intatec logo on body

Installation Requirements:

R001 R040

Expiry date:

30/04/2028

Model:

HS10012CP

Approval Holder:

Intatec Limited

Company Name

Intatec Limited

Address

Airfield Industrial Estate Hixon Staffordshire

Postcode

ST18 0PF

Country

United Kingdom

Phone

01889272180

General Email

ryan.tilsley@intatec.co.uk

View All Listings by this Company

Range of overhead shower outlets. The inlet incorporates a stainless-steel filter washer. Maximum operating temperature 65°C.

Section:

1650 Shower Outlets

Section Subtitle:

Shower head(s) and/or shower handset(s).

WRAS Approval Number:

250912015

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Note:

Open outlet use only.

Size:

½” BSP (F).

Marking:

SUERDA on body.

Installation Requirements:

R001 R040

Expiry date:

30/09/2030

Model:

Round Slim Shower Head: SD42508 - 300mm - Chrome. Square Slim Shower Head: SD42509 - 300mm - Chrome. Square Shower Head: SDH1D121 - 250mm - Chrome, SDH1D121BK - 250mm - Black, SDH1D121BB - 250mm - Brushed Brass. Round Shower Head: TS03301 - 250mm - Chrome, TS03301BK - 250mm - Black, TS03301BB - 250mm - Brushed.

Approval Holder:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Manufacturer:

ZHEJIANG SUERDA SANITARY CO.,LTD.

Company Name

ZHEJIANG SUERDA SANITARY CO.,LTD.

Address

No.39 Changshun Road, Bingang Industrial Zone, Shamen Town, Yuhuan County, Zhejiang

Country

China

View All Listings by this Company

Section:

1650 Shower Outlets

Description:

A Range of Shower head(s) and/or shower handset(s).

Undefinable Air Gap – See IRN’s

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Installation Requirements:

R001 R040

Expiry date:

30/09/2030

Notes & Further Information

Two Fixed Head's with different finish and size as below FH SLRD01 C / BB / GM - (Dia 200mm) FH SLRD02 C - (Dia 250mm) FH SLRD03 C - (Dia 300mm) 225788 - (Wickes selling code for FH SLRD03 C) RP3 FH SLRD01 C - (Dia 200mm, chrome 3) FH TDRD01 C - (Dia 157mm) FH TDRD01 C / G - (Dia 200mm) FH TDRD03 C - (Dia 300mm)

Approval Holder:

Bristan Group Ltd.

Company Name

Bristan Group Ltd.

Address

Birch Coppice Business Park Dorden Tamworth

Postcode

B78 1SG

Country

United Kingdom

Phone

01827 254144

General Email

hmistry@bristan.com

View All Listings by this Company

Range of in-line `Y`-patterned strainers with bronze bodies incorporating stainless steel mesh strainers and PTFE washers. Maximum working pressure 20.0 bar. Maximum operating temperature 85°C.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

1/2”, 3/4”, 1”, 1-1/4”, 1-1/2” & 2” BSP (F)

Marking:

Company logo FIVC, size, pressure rating and flow arrow on body. Product info on data plate.

Installation Requirements:

R001

Expiry date:

30/09/2030

Model:

3657 & FYSXXXO2XXX0121

Approval Holder:

FlowCon International Valve Company (FIVC)

Company Name

FlowCon International Valve Company (FIVC)

Address

Trafikcenter Alle 17, DK-4200 Slagelse, Denmark

Phone

+45 2912 4363

General Email

mt@flowconivc.com

View All Listings by this Company

Range of In-line ‘Y’ patterned strainer with ductile iron bodies (blue epoxy powder coated) and stainless-steel screens. Maximum working pressure 16.0 bar. Maximum operating temperature 85ºC.

Section:

1715 Strainers

Basis of Compliance:

Tested to regulators Specification Test Code Sheets

Size:

DN40-DN300 Flanged.

Marking:

logo, size, PN and WRAS on body. STAINLESS STEEL NAME PLATE Rating – PN16 Size – (TBC) Serial Number – AFC/------/ Tested – EN12266 Date – (date of Manufacture) Model No – TR318

Installation Requirements:

R001

Expiry date:

31/12/2029

Model:

TR318

Approval Holder:

AFFCO Flow control UK

Company Name

AFFCO Flow control UK

Address

unit 7 Stafford park 12 Telford Shropshire

Postcode

TF3 3BJ

Country

United Kingdom

General Email

info@affco-flowcontrol.co.uk

View All Listings by this Company