'Teflon® FEP 100 X, 100-J, 106 X, CJ 95 X, CJ 99 X & 9302 X'. Un-pigmented (white coloured, compression moulded FEP material. For use with water up to 85°C.
''Teflon® PFA 340 X, 345 X, 350 X, 350-T-J, 440 HP X, 445 HP X, 450 HP X & 416 HP X'. Unpigmented (white coloured), compression moulded PFA materials. For use with water up to 85°C.
'Teflon® PTFE 640XT X, 807N X, NXT 70, NXT 75, 6CN X, 62 X, 62N X, 62XT X, 669N X, 669 X, NXT 85, 605XT X, 6C X, 7A X, 641XT X & 650XT X’. White coloured, extruded or compression moulded PTFE material. For use with water up to 85°C.
‘Estane® Grades 58887 Nat 036, 58315 Nat 033, 58300 Nat 036, 58887 Nat 029, 58315 Nat 055, 58887 Nat 038 & 58887 Nat 055’. Natural (transparent, colourless), injection moulded TPU materials. For use with water up to 23°C.
'TOM Oriented PVC (PVC-O) pipe'. Blue coloured PVC pipe manufactured by extrusion and orientation. For use with water up to 60°C.
'STATHEROS EPC80'. Site applied, grey coloured (once mixed), two-component anchor resin, supplied in a cartridge which automatically dispenses in a 1:1 ratio. Apply and cure as per manufacturer's product information 'Ver. 10' dated '02/06/23' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'E7001Z59 (EP02269PF) 2x modified'. Black coloured, compression moulded EPDM 'O' rings. Shore hardness 72 A. Tested in-radii sizes between 1.4mm & 1.8mm. For use with water up to 85°C.
'5613 Gaskets'. Black coloured, compression moulded EPDM gaskets. Shore hardness 60. Tested in-radius size 3.0mm. For use with water up to 23°C.
'TIMO 4-80 ‘O’ rings and washers'. Black coloured, injection moulded EPDM ‘O’ rings and washers. Shore hardness 80. The ‘O’ rings have an in-radius size of between 0.52mm & 2.67mm. The washers have an in-radius size of between 0.52mm & 2.71mm. For use with water up to 85°C.
'TIMO 7-70 washers & 'O' rings'. Black coloured, injection moulded EPDM washers and 'O' rings. Shore hardness 70. Tested in-radii sizes between 0.5 and 2.6mm. For use with water up to 85°C.
'EPDM 70.503-00 'O'-rings and washers'. Black coloured, injection moulded EPDM 'O'-rings and washers. Shore hardness 70. Tested in-radius size between 0.5mm & 2.6mm. For use with water up to 85°C.
'Sunaflex T 8165'. Black coloured, compression moulded EPDM sheet material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 23°C.
'SE-618PF'. Black coloured, compression moulded EPDM material. Shore hardness 60. Tested in-radius size 1.0mm. For use with water up to 85°C.
'Mescola EPDM-PX 659/70.nr'. Black coloured, compression moulded EPDM material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
'0612 HNBR'. Yellow coloured (opaque), injection moulded HNBR 'O' rings. Shore hardness 70. Tested in-radius size 1.31mm. For use with water up to 85°C.
‘N5066F, N5566F, N6066F, N6566F, N7066F, N7566F, N8066F, N8566F & N9066F’. Black coloured, compression moulded NBR rubber `O` rings and gaskets. Shore hardness between 50 & 90. 'O' rings have a tested in-radius size of between 0.25mm & 5.0 mm. Gaskets have a tested in-radius size of between 0.3mm & 7.5mm. For use with water up to 85°C.
‘N70 60 003 197’. Black coloured, injection moulded NBR material. Shore hardness 70. Tested in-radius size 1.0mm. For use with water up to 85°C.
‘SIL40X02, SIL45X02, SIL50X02, SIL55X02, SIL60X02, SIL65X02, SIL75X02 & SIL80X02’. Range of compression moulded, silicone rubber `O` rings and gaskets available in natural, white, grey, blue, red, pale yellow, orange, green, brown and black colours. Shore hardness range 40 - 80. ‘SIL70B02’ – Blue coloured. ‘SIL70W01’ – Natural. ‘SIL70R01’ – Red coloured. ‘SIL7001’ – Black coloured. Range of compression moulded, silicone rubber `O` rings and gaskets available in colours listed above. Shore hardness 70. ‘O’ rings have an in-radius size range of 0.2mm – 5.0mm. Gaskets have an in-radius size range of 0.3mm – 7.5mm. For use with water up to 85°C.
'EMS Force 5543'. 'EMS Force 5543-P' was added to the approval in February 2025. Blue coloured pipe sealants. Apply as per manufacturer's instructions 'TLM.LB.07', version '0', issue date '07/03/2016'. Cure for 24 hours@23°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hinton Thread Sealant HTS50 & HTS250'. Anaerobic adhesive which is available in a yellow colour or in a yellow/orange colour. Apply as per manufacturer's instructions dated '2023-06-07', 'review 6' and cure for 15 minutes@25°C or 24 hours@22°C. For use with water up to 85°C. This product is to be applied and cured in strict accordance with the manufacturer's instructions.
Page 199 of 427
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
