Spherical valves incorporating a drain port and two check valve cartridges (verified by test, suitable for backflow protection against fluid category 3) in a DZR brass body. Above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Screwdriver operated angled spherical valve with a brass body and ball. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Screwdriver operated angled spherical valve with a brass body and ball. Compression connection is to be used with copper pipe EN1057. Maximum working pressure 12.0 bar. Maximum operating temperature 85°C.
Range of in-line spherical valves (brushed chrome DZR brass body) with lever or butterfly type operating members (see models), DZR brass ball (chromium plated brass) and PTFE seats and washers. Maximum working pressure 10.0 bar. Maximum operating temperature 100°C.
Range of gate valves, (brass bodies) controlled via a handwheel with PTFE seals. Maximum working pressure 20.0 bar (L198 models), 16.0 bar (L197 & P474 models). Maximum operating temperature 99°C
Range of gate valves with brass bodies and wedges. Maximum working pressure 17.5 bar. Maximum operating temperature 93°C
Range of gate valves with blue epoxy coated ductile iron bodies. Maximum working pressure 17.24 Bar Maximum operating temperature 99.0°C
Range of gate valves with ductile iron bodies (blue epoxy coated), EPDM coated wedge and EPDM O - rings. Maximum working pressure – 10.0 bar (DN900 and DN1000 only) and 16.0 bar (DN350 – DN800). Maximum operating temperature - 85°C
Range of angled stop valves, (chromium plated brass bodies) with dome operating members. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C
Range of screw down stop valves with brass bodies. All models incorporate a wheel type operating member. Maximum working pressure: 16.0 bar. Maximum operating temperature: 95°C.
`Water block` range of self-closing valves with either a natural (white), blue or grey plastic body and a gear driven volume-controlled operation device. The product incorporates a stainless-steel strainer. The product is designed to stop the flow of water once a preset value (in litres) has been reached. User intervention is then required to reset it. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Range of manually operated balancing valves (DZR Brass body). Maximum working pressure 20.0 bar. Maximum operating temperature 99ºC.
Range of inline water meter kits incorporating brass bodies, a spherical valve and drain off valve. For use with copper pipe (manufactured to BS EN 1057:1996). Maximum working pressure 10.0 bar. Cold water use only.
'FORMOCON FM090'. White coloured, injection moulded POM material. For use with water up to 85°C.
'FORMOCON FM090LMD'. White coloured, injection moulded POM material. For use with water up to 85°C.
'TC-7808-19'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's data sheet dated June 8, 2019. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EKOPIPE 900 Blue’. Factory applied, blue coloured, two-component epoxy coating. Mix parts A & B in a mass ratio of 2:1 and apply as per manufacturer's TDS 'No:09, Rev.Date: January 2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EVER-SRC-1'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2024-09-10', revision 'A0'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'EP015-UTB'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions reference 'PR-CA-00-024' dated 15-02-19. Cure for 15 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'NF 131118'. Factory applied, grey coloured, two-part, water-based epoxy coating. Mix resin and curing agent in a 9:1 weight ratio and apply as per manufacturer's TDS 'PAMCN-V1', dated '20240423'. Cure for 60 minutes@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 171 of 215
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
